change time TOYOTA COROLLA HATCHBACK 2022 (in English) Owner's Guide

2784-5. Using the driving support systems
*: For vehicles with navigation system
Speed limit with supplemental
mark*1
*1: Displayed simultaneously with speed
limit
*2: Contents not recognized.
*3: If the turn signal indicator is not
operated when changing lanes, the
mark does not display.
In the following situations, the RSA
system will notify the driver.
 When the vehicle speed exceeds
the speed notification threshold
of the speed limit sign displayed,
the sign display will be empha-
sized and a buzz er will sound.
 When the RSA system recog-
nizes a no-entry sign and detects
that the vehicle has entered a
no-entry area based on the map
information of the navigation sys-
tem, the no-entry sign flashes
and a buzzer will sound. (For
vehicles with navigation system)
 If it is detected that your vehicle
is overtaking when a no overtak-
ing sign is displayed on the
multi-information display, the dis-
played sign will flash and a
buzzer will sound.
Depending on the situation, traffic
environment (traffic direction,
speed unit) may be detected incor-
rectly and a notification function
may not operate properly.
■Setting procedure
1 Press or of the meter con-
trol switches and select
2 Press or of the meter con-
trol switches and select , then
press
■Automatic turn-off of RSA sign dis-
play
One or more signs automatically turn off in the following situations.
●No sign has been recognized for a certain distance.
●The road changes due to a left or right turn, etc.
No-entry*
End of prohibition
Stop
Wet
Rain
Ice
Supplemental mark
exists*2
Exit ramp on right*3
Exit ramp on left*3
Time
Notification function

279
4
4-5. Using the driving support systems
Driving
■Conditions in which the function
may not operate or detect correctly
In the following situations, RSA does not
operate normally and may not recognize
signs, display the in correct sign, etc. However, this does not indicate a mal-
function.
●The front camera is misaligned due to
a strong impact being applied to the
sensor, etc.
●Dirt, snow, stickers, etc. are on the
windshield near the front camera.
●In inclement weather such as heavy
rain, fog, snow or sand storms.
●Light from an oncoming vehicle, the
sun, etc. enters the front camera.
●The sign is dirty, faded, tilted or bent.
●The contrast of electronic sign is low.
●All or part of the sign is hidden by the leaves of a tree, a pole, etc.
●The sign is only visible to the front camera for a short amount of time.
●The driving scene (turning, lane change, etc.) is judged incorrectly.
●If a sign not appropriate for the cur-rently traveled lane, but the sign exists
directly after a freeway branches, or in
an adjacent lane just before merging.
●Stickers are attached to the rear of the
preceding vehicle.
●A sign resembling a system compati-
ble sign is recognized.
●Side road speed signs may be
detected and displayed (if positioned in sight of the front camera) while the
vehicle is traveling on the main road.
●Roundabout exit road speed signs
may be detected and displayed (if
positioned in sight of the front camera)
while traveling on a roundabout.
●The front of the vehicle is raised or
lowered due to the carried load.
●The surrounding brightness is not suf-
ficient or changes suddenly.
●When a sign intended for trucks, etc.
is recognized.
●The vehicle is driven in a country with
a different direction of traffic.
●The navigation system map data is
outdated.
●The navigation system is not operat-
ing.
●The speed information displayed on
the meter and on the navigation sys- tem may be different due to the navi-
gation system using map data.
■Speed limit sign display
If the engine switch was last turned off while a speed limit sign was displayed
on the multi-information display, the
same sign displays again when the engine switch is turned to ON.
■If “RSA Malfunction Visit Your
Dealer” is shown
The system may be malfunctioning. Have the vehicle inspected by any
authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer.
■Customization
Some functions can be customized.
( P.577)

283
4
4-5. Using the driving support systems
Driving
• The windshield defogger is turned on.
• The steering wheel is operated. • Vehicles with a Multidrive: The shift
lever is shifted to M, N or R from D.
• Vehicles with a Multidrive: The shift lever is shifted from P.
• The driver’s seat belt is unfastened.
• The driver’s door is opened. • Vehicles with a Multidrive: The accel-
erator pedal is depressed.
• The Stop & Start cancel switch is pressed.
• The vehicle starts to roll on an incline.
• When the preceding vehicle starts off when your vehicle is stopped by oper-
ation of the dynamic radar cruise con-
trol with full-speed range. (if equipped) • The driving mode is changed from
NORMAL or ECO mode to another
mode.
●In the following situations, the engine
may restart automatically if the engine is stopped by the Stop & Start system.
(To enable stopping of the engine by
the Stop & Start system, drive the vehicle.)
• The brake pedal is pumped or
strongly depressed. • The air conditioni ng system is being
used.
• The battery is not sufficiently charged. • When a switch of the air conditioning
system is operated (windshield defog-
ger switch, etc.).
■Stop & Start system operation when the brake hold system is
operating
●If the engine is restarted automatically
by the Stop & Start system when the
brake hold system is operating, the brake hold system will continue to
apply the brakes.
●If the operation conditions of the brake hold system are no longer met
( P.192) while the engine is stopped
by the Stop & Start system, the brake hold system will stop operating.
At this time, the parking brake will be
applied automatically and the engine will
be restarted automatically.
■Stop & Start system operation dur-
ing a controlled stop by the dynamic radar cruise control with
full-speed range (if equipped)
If the engine is restarted automatically by the Stop & Start system during a con-
trolled stop by the dynamic radar cruise
control with full-sp eed range, the con- trolled stop will continue. (Resuming fol-
low-up cruising after a controlled stop:
 P.255)
■Hood
●If the hood is opened while the engine
is stopped by the Stop & Start system, the engine will stall and will not be
able to be restarted by the automatic
engine start function. In this case, restart the engine using the normal
engine starting procedure. ( P.177,
178)
●Even if the hood is closed after the
engine is started with the hood open, the Stop & Start system will not oper-
ate. Close the hood, turn the engine
switch off, wait 30 seconds or more, and then start the engine.
■When to use the Stop & Start sys-
tem
●When stopping the vehicle for a
longer period of time, turn the engine
switch off and stop the engine com- pletely.
●When the system does not operate, is canceled, or is malfunctioning, warn-
ing messages and a warning buzzer
are used to inform the driver. ( P.285)
●If the engine switch is pressed when the engine is stopped by the Stop &
Start system, the engine will stall and
will not be able to be restarted by the
automatic engine start function. In this case, restart the engine using the nor-
mal engine starting procedure.
( P.177, 178)
●When the engine is restarted by the
Stop & Start system, the power outlet may be temporarily unusable, but this
is not a malfunction.

2844-5. Using the driving support systems
●Installation and removal of electrical
components and wireless devices may affect the Stop & Start system.
Contact any authorized Toyota retailer
or Toyota authorized repairer, or any reliable repairer for details.
●When the engine is restarted by the Stop & Start system, the steering
wheel may temporarily feel heavy.
■If the windshield is fogged up while
the engine is stopped by the Stop & Start system
Turn the windshield defogger on. (The
engine will start due to the automatic engine start function.): P.424, 429
If the windshield fogs up frequently,
press the Stop & Start cancel switch to disable the system.
■Air conditioning system operation
while the engine is stopped by the
Stop & Start system
●If the air conditioning system is being
used in automatic mode, the fan speed may be reduced or the fan may
be stopped while the engine is
stopped by the Stop & Start system in order to reduce changes in the cabin
temperature.
●To ensure air cond itioning system per-
formance when the vehicle is stopped,
disable the Stop & Start system by pressing the Stop & Start cancel
switch.
■If an odor comes from the air condi-
tioning system while the engine is stopped by the Stop & Start system
Vehicles with a manual air conditioning
system: If the idling stop time is set to “Extended”, change the setting to
“Standard”.
If an odor occurs even when “Standard”
is selected, press the Stop & Start can- cel switch to deactivate the Stop & Start
system.
Vehicles with an automatic air condition- ing system: Press the Stop & Start can-
cel switch to deactivate the Stop & Start
system.
■Changing the idling stop time with
the air conditioning system on
The length of time the Stop & Start sys-
tem will operate when the air condition-
ing system is on can be changed in
of the multi-information display ( P. 9 9 ) .
(The length of time the Stop & Start sys-
tem will operate when the air condition- ing system is off cannot be changed.)
■When a buzzer sounds
Vehicles with a Multidrive: If the driver's
door is opened when the engine is stopped by the Stop & Start system and
the shift lever is in D, a buzzer will sound
and the Stop & Start system indicator will flash. To stop the buzzer, close the
driver's door.
■The Stop & Start system protection
function
●When the volume of the audio system
is excessively high, sound output from the audio system may suddenly be cut
off in order to reduce battery con-
sumption. To prevent the audio sys- tem from being cut off, keep the
volume of audio system at a moderate
level. If the audio system has been cut off,
turn the engine switch off, wait for 3
seconds or more and then turn it to ACC or ON to re-enable the audio
system.
●The audio system may not be acti-
vated if the battery terminals are dis-
connected and then reconnected. If this occurs, turn the engine switch off
and then repeat the following opera-
tion twice to activate the audio system
normally. • Turn the engine switch to ON and
then to off.
■Replacing the battery
 P. 5 5 9
■Displaying the Stop & Start system information
 P. 1 0 5

287
4
4-5. Using the driving support systems
Driving
Press the Stop & Start cancel
switch to disable the Stop & Start
system.
The Stop & Start cancel indicator will
come on.
Pressing the switch again will enable
the Stop & Start syst em and the Stop &
Start cancel indicator will turn off.
■Automatic reactivation of the Stop
& Start system
Even if the Stop & Start system is disa- bled by the Stop & Start cancel switch, it
will be automatically re-enabled once
the engine switch is turned off and then the engine is started.
■If the Stop & Start cancel switch is
pressed while the vehicle is stopped
●When the engine is stopped by the Stop & Start system, pressing the Stop
& Start cancel switch will restart the
engine.
●With the Stop & Start system disabled,
pressing the Stop & Start cancel switch will re-enable the system but
not stop the engine.
From the next time the vehicle is stopped (after Stop & Start system
has been enabled), the engine will be
stopped.
After the engine is stopped by the
Stop & Start system when the vehi-
cle is on an incline, brake force is
temporarily maintained to prevent
rolling backwards unt il the engine is
restarted and drive force is gener-
ated.
When drive force is generated, the
maintained brake force is automati-
cally canceled.
 This function operates on flat
surfaces as well as steep
inclines.
 Sound may be generated from
the brakes, but this is not a mal-
function.
 Brake pedal response may
change and vibration may occur,
but these are not malfunctions.
NOTICE
●Even though the driver’s door is
open, the open door warning light
does not illuminate or the interior light does not illuminate when the
interior light switch is in the door
position.
■If the engine stalls (vehicles with
a manual transmission)
If the Stop & Star t system is enabled and the clutch pedal is depressed
quickly, the engine may restart.
Disabling the Stop & Start
systemHill-start assist control
(vehicles with a Multidrive)

311
4
4-5. Using the driving support systems
Driving
When the vehicle comes within
approximately 30 cm (1.0 ft.) of
the object, the buzzer sounds
continuously.
 When 2 or more objects are
detected simultaneously, the
buzzer sounds for the nearest
object. If one or more objects
come within approximately 30
cm (1.0 ft.) of the vehicle, the
buzzer will repeat a long tone,
followed by fast beeps.
 Automatic buzzer mute function:
After a buzzer begins sounding,
if the distance between the vehi-
cle and the detected object does
not become shorter, the buzzer
will be muted automatically.
(However, if the distance
between the vehicle and object is
30 cm (1.0 ft.) or less, this func-
tion will not operate.)
■Adjusting the buzzer volume
The buzzer volume can be adjusted
on the multi-information display.
The volume of buzzers for the
Toyota parking assist-sensor and
RCTA function (if equipped) will be
adjusted simultaneously.
Use the meter control switches to
change settings. ( P.100)
1 Press or to select .
2 Press or to select
and then press and hold .
3 Select the volume and then
press .
Each time the switch is pressed, the
volume level will change between 1, 2,
and 3.
■Muting a buzzer
A mute button will be displayed on
the multi-information display when
an object is detected. To mute the
buzzer, press .
The buzzers for the Toyota parking
assist-sensor and RCTA function (if
equipped) will be muted simultane-
ously.
Mute will be canceled automatically
in the following situations:
 When the shift lever is changed.
 When the vehicle speed exceeds
a certain speed.
 When the operating function is
temporarily canceled.
 When the operating function is
disabled manually.
 When the engine switch is turned
off.

3124-5. Using the driving support systems
*: If equipped
Meter control switches
Turning the RCTA function on/off.
When the RCTA function is disabled,
the RCTA OFF indicator illuminates.
Outside rear view mirror indica-
tors
When a vehicle approaching from the
right or left at the rear of the vehicle is
detected, both outside rear view mirror
indicators will flash.
RCTA buzzer
If a vehicle approaching from the right
or left at the rear of the vehicle is
detected, a buzzer will sound. The
buzzer also sounds for approximately 1
second immediately after the RCTA
function is turned on.
Use the meter control switches to
enable/disable the RCTA function.
( P. 1 0 0 )
1 Press or to select .
2 Press or to select
“RCTA” and then press .
When the RCTA function is disabled, the RCTA OFF indicator ( P.87) illumi-
nates. (Each time the engine switch is
turned off then changed to ON, the
RCTA function will be enabled automat- ically.)
RCTA (Rear Crossing
Traffic Alert) function*
The RCTA function uses the
BSM rear side radar sensors
installed behind the rear
bumper. This function is
intended to assist the driver in
checking areas that are not
easily visible when backing up.
WA R N I N G
■Cautions regarding the use of the system
There is a limit to the degree of recog-
nition accuracy and control perfor- mance that this system can
provide,do not overly rely on this sys-
tem. The driver is always responsible for paying attention to the vehicle’s
surroundings and driving safely.
( P.288)
■To ensure the system can oper-
ate properply
 P.300
System components
Turning the RCTA function
on/off

3144-5. Using the driving support systems
■RCTA function detection areas
The areas that vehicles can be detected in are outlined below.
The buzzer can alert the driver of
faster vehicles approaching from
farther away.
Example:
■The RCTA function is operational
when
The RCTA function operates when all of
the following conditions are met:
●The engine switch is in ON.
●The RCTA function is on.
●The shift lever is in R.
●The vehicle speed is approximately 15
km/h (9 mph) or less.
●The approaching vehicle speed is
between approximately 8 km/h (5
mph) and 56 km/h (34 mph).
■Adjusting the buzzer volume
The buzzer volume can be adjusted on the multi-information display. The vol-
ume of buzzers for the Toyota parking
assist-sensor and RCTA function will be adjusted simultaneously.
Use the meter control switches to change settings. ( P.100)
1 Press or to select .
2 Press or to select “RCTA”
and then press and hold .
3 Select the volume and then press
.
Each time the switch is pressed, the vol-
ume level will change between 1, 2 and
3.
■Muting a buzzer
A mute button will be displayed on the
multi-information display when an object
is detected. To mute the buzzer, press
.
The buzzers for the Toyota parking
assist-sensor and RCTA function will be muted simultaneously.
Mute will be canceled automatically in
the following situations:
●When the shift lever is changed.
●When the vehicle speed exceeds a
certain speed.
●When the operating function is tempo-
rarily canceled.
●When the operating function is disa-
bled manually.
●When the engine switch is turned off.
Approaching vehi-
cle speed
Approximate
alert distance
56 km/h (34 mph)
(fast)40 m (131 ft.)
8 km/h (5 mph)
(slow)5.5 m (18 ft.)

3184-5. Using the driving support systems
detection area behind the vehicle
when backing up. ( P.327)
The Parking Support Brake can be
enabled/disabled on the multi-infor-
mation display. All of the Parking
WA R N I N G
■Cautions regarding the use of
the system
Do not overly rely on the system, as
doing so may lead to an accident.
●The driver is solely responsible for safe driving. Always drive carefully,
taking care to observe your
surroundings. The Parking Support Brake system is designed to pro-
vide support to lessen the severity
of collisions. However, it may not operate in some situations.
●The Parking Support Brake system is not designed to stop the vehicle
completely. Additionally, even if the
system has stopped the vehicle, it is necessary to depress the brake
pedal immediately as brake control
will be canceled after approximately 2 seconds.
●It is extremely dangerous to check the system operatio ns by intention-
ally driving the vehicle into the
direction of a wall, etc. Never attempt such actions.
■When to disable the Parking Sup-port Brake
In the following situations, disable the
Parking Support Br ake as the system may operate even though there is no
possibility of a collision.
●When inspecting the vehicle using
a chassis roller, chassis dynamo or
free roller
●When loading the vehicle onto a
boat, truck or other transport vessel
●If the suspension has been modi-
fied or tires of a size other than specified are installed
●If the front of the vehicle is raised or lowered due to the carried load
●When equipment that may obstruct a sensor is installed, such as a tow-
ing eyelet, bumper protector (an
additional trim strip, etc.), bicycle carrier, or snow plow
●When using automatic car washing devices
●If the vehicle cannot be driven in a stable manner, such as when the
vehicle has been in an accident or
is malfunctioning
●When the vehicle is driven in a
sporty manner or off-road
●When the tires are not properly
inflated
●When the tires are very worn
●When a tire chains, compact spare
tire or an emergency tire puncture
repair kit is used
NOTICE
■If “Parking Support Brake Una- vailable” is displayed on the
multi-information display and the
PKSB OFF indicator is flashing
If this message is displayed immedi-
ately after the engine switch is
changed to ON, operate the vehicle carefully, paying attention to your
surroundings. It may be necessary to
drive the vehicle for a certain amount of time before the system returns to
normal. (If the system does not return
to normal after driving for a while, clean the sensors and their surround-
ing area on the bumpers.)
Enabling/Disabling the Park-
ing Support Brake

3224-5. Using the driving support systems
Time
Engine output restriction control begins operating
System determines that possibility of collision with detected object is
high
Engine output reduced
System determines that possibility of collision with detected object is
extremely high
Brake control begins operating
Brake control strength increased
Example: Multi-informat ion display: “Brake!”
Example: Multi-information di splay: “Switch to Brake”
■If the Parking Support Brake has operated
If the vehicle is stopped due to operation
of the Parking Support Brake, the Park- ing Support Brake will be disabled and
the PKSB OFF indicator will illuminate. If
the Parking Support Brake operates unnecessarily, brake control can be
canceled by depressing the brake pedal
or waiting for approximately 2 seconds for it to automatically be canceled. Then,
the vehicle can be operated by depress-
ing the accelerator pedal.
■Re-enabling the Parking Support Brake
To re-enable the Parking Support Brake
when it is disabled due to operation of the Parking Support Brake, either ena-
ble the system again ( P.318), or turn
the engine switch off and then back to ON. Additionally, if the object becomes
no longer in the traveling direction of the
vehicle or if the traveling direction of the vehicle changes (such as changing from
moving forward to backing up, or from
backing up to moving forward), the sys-
tem will be re-enabled automatically.
■If “Parking Support Brake Unavaila-
ble” is displayed on the multi-infor- mation display and the PKSB OFF
indicator is flashing
●If this message is displayed, a sensor
on the front or rear bumper may be
dirty. Clean the sensors and their sur- rounding area on the bumpers.
■If “Parking Support Brake Unavaila-
ble” and “Parking Assist Unavaila-
ble Clean Parking Assist Sensor” are displayed on the multi-informa-
tion display and the PKSB OFF
indicator is flashing
●A sensor may be covered with ice,
snow, dirt, etc. Remove the ice, snow, dirt, etc., from the sensor to return the
system to normal. If this message
continues to be displayed even after cleaning the sensor, or is displayed
even though the sensor is clean, have
the vehicle inspected by any author- ized Toyota retailer or Toyota author-
ized repairer, or any reliable repairer.
●A sensor may be frozen. Once the ice
melts, the system will return to nor-
mal.
●Water may be continuously flowing
over the sensor surface, such as in a heavy rain. When the system deter-
mines that it is normal, the system will