height TOYOTA iM 2016 Owners Manual (in English)

271-1. For safe use
1
For safety and security
Scion iM_U (12J49U)
Push the seat belt shoulder
anchor down while pressing the
release button.
Push the seat belt shoulder
anchor up.
Move the height adjuster up and
down as needed until you hear a
click.
The pretensioners help the seat
belts to quickly restrain the occu-
pants by retracting the seat belts
when the vehicle is subjected to
certain types of severe frontal or
side collision or a vehicle rollover.
The pretensioners do not activate
in the event of a minor frontal
impact, a minor side impact or a
rear impact.
Adjusting the seat belt shoulder anchor height (front seats)
1
2
Seat belt pretensioners (front seats)

95
3
Operation of each component
Scion iM_U (12J49U)
3-3. Adjusting the seats
Front seats
Adjustment procedure
Seat position adjustment lever
Seatback angle adjustment
lever Vertical height adjustment
lever (driver’s side only)
WARNING
n
When adjusting the seat position
lTake care when adjusting the seat position to ensure that other passen-
gers are not injured by the moving seat.
l Do not put your hands under the seat or near the moving parts to avoid
injury.
Fingers or hands may become jammed in the seat mechanism.
l Make sure to leave enough space around the feet so they do not get stuck.
n Seat adjustment
lBe careful that the seat does not hit passengers or luggage.
l To reduce the risk of sliding under the lap belt during a collision, do not
recline the seat more than necessary.
If the seat is too reclined, the lap belt may slide past the hips and apply
restraint forces directly to the abdomen, or your neck may contact the
shoulder belt, increasing the risk of death or serious injury in the event of
an accident.
Adjustments should not be made while driving as the seat may unexpect-
edly move and cause the driver to lose control of the vehicle.
l After adjusting the seat, make sure that the seat is locked in position.
1
2
3

1003-3. Adjusting the seats
Scion iM_U (12J49U)
Rear outside seats
n Adjusting the height of the head restraints
n Adjusting the rear center seat head restraint
Always raise the head restraint one level from the stowed position when
using. Align the head restraint with the installa-
tion holes and push it down to the lock
position.
Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.
WARNING
nHead restraint precautions
Observe the following precautions regarding the head restraints. Failure to
do so may result in death or serious injury.
lUse the head restraints designed for each respective seat.
l Adjust the head restraints to the correct position at all times.
l After adjusting the head restraints, push down on them and make sure
they are locked in position.
l Do not drive with the head restraints removed.

1033-4. Adjusting the steering wheel and mirrors
3
Operation of each component
Scion iM_U (12J49U)
The height of the rear view mirror can be adjusted to suit your driving
posture.
Adjust the height of the rear view
mirror by moving it up and down.
Reflected light from the headlights of vehicles behind can be reduced
by operating the lever.
Normal position
Anti-glare position
Inside rear view mirror
The rear view mirror’s position can be adjusted to enable suffi-
cient confirmation of the rear view.
Adjusting the height of rear view mirror
Anti-glare function
1
2
WARNING
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident,
resulting in death or serious injury.

2747-2. Steps to take in an emergency
Scion iM_U (12J49U)
Remove the deck mat. (P. 182)
Take out the jack. For tightening
For loosening
WARNING
nUsing the tire jack
Observe the following precautions.
Improper use of the tire jack may cause the vehicle to suddenly fall off
the jack, leading to d eath or serious injury.
lDo not use the tire jack for any purpose other than replacing tires.
lOnly use the tire jack that comes with this vehicle for replacing a flat
tire.
Do not use it on other vehicles, and do not use other tire jacks for
replacing tires on this vehicle.
lPut the jack properly in its jack point.
lDo not put any part of your body und er the vehicle while it is supported
by the jack.
lDo not start the engine or drive the vehicle while the vehicle is sup-
ported by the jack.
lDo not raise the vehicle while someone is inside.
lWhen raising the vehicle, do not put an object on or under the jack.
lDo not raise the vehicle to a height greater than that required to
replace the tire.
lUse a jack stand if it is necessary to get under the vehicle.
lWhen lowering the vehicle, make su re that there is no-one near the
vehicle. If there are people nearby, warn them vocally before lowering.
Taking out the jack
1
2
1
2

294
Scion iM_U (12J49U)
8-1.Specifications
*: Unladen vehicles
n
Vehicle identification number
The vehicle identification number (VIN) is the legal identifier for
your vehicle. This is the primar y identification number for your
Scion. It is used in registerin g the ownership of your vehicle.
This number is stamped under
the right-hand front seat.
Maintenance data (fuel, oil level, etc.)
Dimensions and weights
Overall length 170.5 in. (4330 mm)
Overall width 69.3 in. (1760 mm)
Overall height*58.1 in. (1475 mm)
Wheelbase102.4 in. (2600 mm)
TreadFront59.6 in. (1515 mm)
Rear59.3 in. (1505 mm)
Vehicle capacity weight
(occupants + luggage) 915 lb. (415 kg)
Vehicle identification

3098-1. Specifications
8
Vehicle specifications
Scion iM_U (12J49U)n
Typical tire size information
The illustration in
dicates typical
tire size.
Tire use (P = Passenger car,
T = Temporary use)
Section width (millimeters)
Aspect ratio
(tire height to section width)
Tire construction code
(R = Radial, D = Diagonal)
Wheel diameter (inches)
Load index
(2 digits or 3 digits)
Speed symbol
(alphabet with one letter)
nTire dimensions
Section width
Tire height
Wheel diameter
Tire size
1
2
3
4
5
6
7
1
2
3