lock TOYOTA IQ 2013 Repair Manual

210 4-3. Do-it-yourself maintenance
■Adding engine oil
If the oil level is below or near
the low level mark, add engine
oil of the same type as already in
the engine.
Make sure to check the oil type and prepare the items needed before
adding oil. Remove the engine oil filler cap by turning it counterclock-
wise.
Add engine oil slowly.
Checking the dipstick.
Reinstall the engine oil filler cap by turning it clockwise.
The approximate quantity of oil needed to raise the level between low and
full on the dipstick is indicated as follows:
1.6 qt. (1.5 L, 1.3 Imp. qt.)
Engine oil selectionP. 319
ItemsClean funnel

222 4-3. Do-it-yourself maintenance
Push and hold the tire pressure
warning reset switch until the
tire pressure warning light blinks
slowly 3 times.
Wait for a few minutes with the engine switch on, and then
turn the engine switch to the ACC or LOCK position.
Registering ID codes
The tire pressure warning valve and transmitter is equipped with a
unique ID code. When replacing a tire pressure warning valve and
transmitter, it is necessary to regi ster the ID code of tire pressure
warning valve and transmitter. Have the ID code registered by your
Scion dealer.
■When to replace your vehicle’s tires
Tires should be replaced if:
●You have tire damage such as cuts, splits, cracks deep enough to
expose the fabric or bulges indicating internal damage
●A tire goes flat repeatedly or c annot be properly repaired due to the
size or location of a cut or other damage
If you are not sure, consul t with your Scion dealer.

234
4-3. Do-it-yourself maintenance
Air conditioning filter
The air conditioning filter must be cleaned or changed regularly to
maintain air conditioning efficiency.
■ Removal method
Turn the engine switch to the LOCK position.
Remove the filter cover.
Remove the air conditioning
filter from between the knee
airbag support and dash panel
insulator.
When removing the air condi-
tioning filter, make sure that
dust or dirt does not enter the
air conditioning system.
UP
E
Knee
airbag
support
Dash
panel
insulator

240
4-3. Do-it-yourself maintenance
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have
blown. If this happens, check and replace the fuses as necessary.
Turn the engine switch to the LOCK position.
The fuses are located in the following places. To check the
fuses, follow the in structions below.
■ Engine compartment
Ty p e A
Remove the cover.

245
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
Engine compartment (type B)
FuseAmpereCircuit
1 D/C CUT 30 A ECU-B NO.1, DOME
2 IMMOBI 7.5 AMultiport fuel injection system/
sequential multiport fuel injection
system
3 TURN & HAZ 10 A Turn signal lights, emergency
flashers
4 ETCS 10 A Electronic throttle control system
5 ECU-B NO.2 5 A Meter, power windows, air condi-
tioning system
6H-LP MAIN
*120 A H-LP RH LO, H-LP LH LO
7 SPARE 30 A Spare fuse
8 SPARE 20 A Spare fuse
9 SPARE 5 A Spare fuse
10 AM2 NO.1 30 A Starting system 11 H-LP MAIN HI
*225 A H-LP RH HI, H-LP LH HI
12 DOME 15 A Interior light, audio system
13 ECU-B NO.1 7.5 A Main body ECU, power door lock
system

246 4-3. Do-it-yourself maintenance
*1: Vehicles with daytime running light system
*2: Vehicles without daytime running light system14 MIR HTR 7.5 A Outside rear view mirror defoggers
15 DEFOGGER 30 A Rear window defogger
16 EPS 50 A Electric power steering
17 RDI 30 A RDI FAN
18 ABS NO.1 50 A Anti-lock brake system
19 HTR-B 40 A HTR, BLR
20 ABS NO.2 30 A Anti-lock brake system
21 HORN 10 A Horn
22 EFI-MAIN 20 A
Multiport fuel injection system/
sequential multiport fuel injection
system, EFI NO.1, Fuel pump
23 ALT-S 7.5 A Charging system
24 IGN 15 A Injection, igniter
25 IG2 10 A SRS airbag system, meter
26 EFI NO.1 10 AMultiport fuel injection system/
sequential multiport fuel injection
system
FuseAmpereCircuit

248 4-3. Do-it-yourself maintenance
■Under the driver’s side instrument panel
FuseAmpereCircuit
1 ECU-IG NO.1 7.5 A Vehicle stability control system,
shift lock control system, electric
power steering, automatic head-
light system, main body ECU, tire
pressure warning system
2 GAUGE 10 A Electric cooling fan, charging sys-
tem, emergency flashers, front
passenger’s seat belt reminder
light, back-up lights, multiport fuel
injection system/sequential multi-
port fuel injection system, wind-
shield wiper ECU
3 HTR-IG 10 A Air conditioning system, rear win-
dow defogger
4 WASHER RR 10 A Windshield washer
5 WIPER RR 10 A Rear window wiper
6 WIPER FR 25 A Windshield wipers
7 WASHER FR 10 A Windshield washer
8 OBD 7.5 A On-board diagnosis system
9 DOOR NO.2 20 A Power windows

249
4-3. Do-it-yourself maintenance
4
Maintenance and care
*: Vehicles with daytime running light system
10 D/L NO.1
15 APower door lock system, main
body ECU
11 DOOR NO.1 30 A Power windows
12 CIG 15 A Power outlet
13 ACC 5 AOutside rear view mirrors, audio
system, shift lock control system,
main body ECU
14
PANEL NO.1*5 A Meter
15 TAIL
*10 A Parking lights, tail lights, license
plate lights, multiport fuel injection
system/sequential multiport fuel
injection system, instrument clus-
ter, windshield wiper ECU
16 (FOG FR) 15 A No circuit
17 AM1 7.5 A ACC, starting system
18 STOP 10 A Vehicle stability control system,
power management ECU, shift
lock control system, stop lights,
multiport fuel injection system/
sequential multiport fuel injection
system
19 (SEAT-HTR) 15 A No circuit
■ After a fuse is replaced
●If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. ( P. 251)
● If the replaced fuse blows again, have the vehicle inspected by your
Scion dealer.
■ If there is an overload in the circuits
The fuses are designed to blow, protecting the wiring harness from damage.
FuseAmpereCircuit

253
4-3. Do-it-yourself maintenance
4
Maintenance and care
Turn the cover clockwise.
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.

254 4-3. Do-it-yourself maintenance
Right sideTurn the cover counterclockwise.
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.