engine oil TOYOTA LAND CRUISER 1996 J80 Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1996 J80Pages: 1399, PDF Size: 41.35 MB
Page 1258 of 1399
Z15498
PS GearClosed
SST PS Vane
Pump
Oil
Reservoir
−
STEERING POWER STEERING FLUID
SR−5
1996 LAND CRUISER (RM451U)
2. CHECK STEERING FLUID PRESSURE
(a) Disconnect the pressure feed tube from the PS vane
pump (See page SR−23).
(b) Connect SST over 2 new gaskets, as shown below. SST 09640 −10010 (09641 −01010, 09641 −01030,
09641 −01060)
NOTICE:
Check that the valve of the SST is in the open position.
(c) Bleed the power steering system (See page SR−3).
(d) Start the engine and run it at idle.
(e) Turn the steering wheel from lock to lock several times to
boost fluid temperature.
Fluid temperature: 80° C (176°F)
(f) With the engine idling, close the valve of the SST and ob-
serve the reading on the SST.
Minimum fluid pressure:
9,316kPa (95 kgf/cm
2, 1,351 psi)
NOTICE:
Do not keep the valve closed for more than 10 se-
conds.
Do not let the fluid temperature become too high.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1259 of 1399
Z15499
PS GearSSTPS Vane
Pump
Oil
Reservoir
Open
Z15500
PS Gear
SSTPS Vane
Pump
Oil
Reservoir
Open
Lock Position
SR−6
−
STEERING POWER STEERING FLUID
1996 LAND CRUISER (RM451U)
(g) With the engine idling, open the valve fully.
(h) Measure the fluid pressure at engine speeds of 1,000 rpm
and 3,000 rpm.
Difference fluid pressure:
490 kPa (5 kgf/cm
2, 71 psi) or less
NOTICE:
Do not turn the steering wheel.
(i) With the engine idling and valve fully opened, turn the steering wheel to full lock.
Minimum fluid pressure:
9,316 kPa (95 kgf/cm
2, 1,351 psi)
NOTICE:
Do not maintain lock position for more than 10 se-
conds.
Do not let the fluid temperature become too high.
(j) Disconnect the SST.
(k) Connect the pressure feed tube (See page SR−32).
(l) Bleed the power steering system (See page SR−3).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1305 of 1399
SS1EO−04
SS−4
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
127
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE MECHANICAL
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,176 kPa (12.0 kgf/cm2, 171 psi) or more
883 kPa (9.0 kgf/cm2, 128 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve clearanceat cold Intake Exhaust0.15 − 0.25 mm (0.006 − 0.010 in.)
0.25 − 0.35 mm (0.010 − 0.014 in.)
Ignition timingw/ Terminals TE1 and E1 connected3° BTDC @ idle
Idle speed−650 ± 50 rpm
Cylinder headWarpage
Cylinder block side Maximum
Manifold side Maximum
Valve seat
Refacing angle Intake
Exhaust
Contacting angle
Contacting width Intake
Exhaust
Cylinder head bolt outside diameter STD
Minimum
0.15 mm (0.0059 in.)
0.10 mm (0.0039 in.)
30°, 45° , 75°
45 °, 75°
45 °
1.2 − 1.6 mm (0.047 − 0.063 in.)
1.0 − 1.4 mm (0.039 − 0.055 in.)
10.85 − 11.00 mm (0.4272 − 0.4331 in.)
10.6 mm (0.417 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD O/S 0.05
Protrusion height7.010 − 7.030 mm (0.2760 − 0.2768 in.)
11.492 − 11.513 mm (0.4524 − 0.4533 in.)
11.542 − 11.563 mm (0.4544 − 0.4522 in.)
8.2 − 8.6 mm (0.323 − 0.339 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake Exhaust
Valve face angle
Stem diameter Intake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum98.4 mm (3.874 in.)
97.9 mm (3.854 in.)
97.9 mm (3.854 in.)
97.4 mm (3.835 in.)
44.5 °
6.970 − 6.985 mm (0.2744 − 0.2750 in.)
6.965 − 6.980 mm (0.2742 − 0.2748 in.)
0.025 − 0.060 mm (0.0010 − 0.0024 in.)
0.030 − 0.065 mm (0.0012 − 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.2 mm (0.047 in.)
1.0 mm (0.039 in.)
Valve springDeviation Maximum
Free length
Installed tension at 36.5 mm (1.437 in.)2.0 mm (0.079 in.)
43.94 − 45.06 mm (1.7299 − 1.7740 in.)
214 − 238 N (21.8 − 24.2 kgf, 48.1 − 53.4 lbf)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum33.966 − 33.976 mm (1.3372 − 1.3376 in.)
34.000 − 34.021 mm (1.3386 − 1.3394 in.)
0.024 − 0.055 mm (0.0009 − 0.0022 in.)
0.07 mm (0.0028 in.)
ManifoldWarpage Maximum0.30 mm (0.0118 in.)
Air intake chamberWarpageMaximum0.30 mm (0.0118 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1306 of 1399
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−5
128
Author: Date:
1996 LAND CRUISER (RM451U)
Camshaft
Thrust clearance
STD
Maximum
Journal oil clearance STD
Maximum
Journal diameter
Circle runout Maximum
Cam lobe height STD
Minimum
Camshaft gear backlash STD
Maximum
Camshaft gear spring end free distance0.030 − 0.080 mm (0.0012 − 0.0031 in.)
0.10 mm (0.0039 in.)
0.025 − 0.062 mm (0.0010 − 0.0024 in.)
0.10 mm (0.0039 in.)
26.959 − 26.975 mm (1.0614 − 1.0620 in.)
0.06 mm (0.0024 in.)
50.61 − 50.71 mm (1.9925 − 1.9965 in.)
50.51 mm (1.9886 in.)
0.020 − 0.200 mm (0.0008 − 0.0079 in.)
0.30 mm (0.0188 in.)
18.2 − 18.8 mm (0.712 − 0.740 in.)
Spark plug tubeProtrusion45.5 mm (1.791 in.)
Oil pump drive
shaft gearThrust clearance STD
Maximum0.040 − 0.160 mm (0.0016 − 0.0063 in.)
0.30 mm (0.0188 in.)
Chain and timing
gearChain length at 16 links Maximum
Camshaft timing gear wear (w/ Chain) Minimum
Crankshaft timing gear wear (w/ Chain) Minimum146.6 mm (5.772 in.)
126.0 mm (4.961 in.)
65.4 mm (2.575 in.)
Chain tensioner
slipper and vibra-
tion damperWearMaximum1.0 mm (0.039 in.)
Cylinder blockCylinder head surface warpageMaximum
Cylinder bore diameter STD Mark 1
2
3
Maximum STD
O/S 0.50
O/S 1.00
Main bearing bolt outside diameter STD
Minimum0.05 mm (0.0020 in.)
100.000 − 100.010 mm (3.9370 − 3.9374 in.)
100.010 − 100.020 mm (3.9374 − 3.9378 in.)
100.020 − 100.030 mm (3.9378 − 3.9382 in.)
100.23 mm (3.9461 in.)
100.73 mm (3.9658 in.)
101.23 mm (3.9854 in.)
10.85 − 11.00 mm (0.4271 − 0.4331 in.)
10.6 mm (0.417 in.)
Piston and piston
ringPiston diameter STD Mark 1
2
3
O/S 0.50
O/S 1.00
Piston oil clearance STD
Piston ring groove clearance No. 1
No. 2
Piston ring end gap STD No. 1
No. 2
Oil
Maximum No. 1 No. 2Oil99.950 − 99.960 mm (3.9350 − 3.9354 in.)
99.960 − 99.970 mm (3.9354 − 3.9358 in.)
99.970 − 99.980 mm (3.9358 − 3.9362 in.)
100.450 − 100.480 mm (3.9547 − 3.9559 in.)
100.950 − 100.980 mm (3.9744 − 3.9756 in.)
0.040 − 0.060 mm (0.0016 − 0.0024 in.)
0.040 − 0.080 mm (0.0016 − 0.0031 in.)
0.300 − 0.070 mm (0.0012 − 0.0028 in.)
0.300 − 0.520 mm (0.0118 − 0.0205 in.)
0.450 − 0.670 mm (0.0177 − 0.0264 in.)
0.150 − 0.520 mm (0.0059 − 0.0205 in.)
1.12 mm (0.0441 in.)
1.17 mm (0.0461 in.)
1.12 mm (0.0441 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1307 of 1399
SS−6
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
129
Author: Date:
1996 LAND CRUISER (RM451U)
Connecting rod
Thrust clearance
STD
Maximum
Connecting rod bearing center wall thickness (Reference) Mark 23
4
5
6
Connecting rod oil clearance STD STD
U/S 0.25
Maximum
Rod bend Maximum per 100 mm (3.94 in.)
Rod twist Maximum per 100 mm (3.94 in.)
Bushing inside diameter
Piston pin diameter
Piston pin oil clearance STD
Maximum
Connecting rod bolt outside diameter STD
Minimum0.160 − 0.262 mm (0.0063 − 0.0103 in.)
0.362 mm (0.0143 in.)
1.744 − 1.747 mm (0.0687 − 0.0688 in.)
1.747 − 1.750 mm (0.0688 − 0.0689 in.)
1.750 − 1.753 mm (0.0689 − 0.0690 in.)
1.753 − 1.756 mm (0.0690 − 0.0691 in.)
1.756 − 1.759 mm (0.0691 − 0.0693 in.)
0.032 − 0.050 mm (0.0013 − 0.0020 in.)
0.033 − 0.073 mm (0.0013 − 0.0029 in.)
0.10 mm (0.0039 in.)
0.05 mm (0.0020 in.)
0.015 mm (0.0059 in.)
26.008 − 26.020 mm (1.0239 − 1.0244 in.)
26.000 − 22.012 mm (1.0236 − 1.0241 in.)
0.004 − 0.012 mm (0.0002 − 0.0005 in)
0.05 mm (0.0020 in.)
8.40 − 8.60 mm (0.3307 − 0.3386 in.)
8.00 mm (0.3150 in.)
CrankshaftThrust clearance STD
Maximum
Thrust washer thickness STD
O/S 0.125
O/S 0.250
Main journal oil clearance STD STD
U/S 0.25
Maximum
Main journal diameter STD
U/S 0.25
Main bearing center wall thickness (Reference) Mark 2 3
4
5
6
Crank pin diameter STD
U/S 0.25
Circle runout Maximum
Main journal taper and out −of− round Maximum
Crank pin taper and out −of− round Maximum0.020 − 0.220 mm (0.0008 − 0.0087 in.)
0.30 mm (0.0118 in.)
2.440 − 2.490 mm (0.0961 − 0.0980 in.)
2.503 − 2.553 mm (0.0985 − 0.1005 in.)
2.565 − 2.615 mm (0.1010 − 0.1030 in.)
0.042 − 0.060 mm (0.0017 − 0.0024 in.)
0.041 − 0.081 mm (0.0016 − 0.0032 in.)
0.10 mm (0.0039 in.)
68.982 − 69.000 mm (2.7158 − 2.7165 in.)
68.745 − 68.755 mm (2.7065 − 2.7069 in.)
2.489 − 2.492 mm (0.0980 − 0.0981 in.)
2.492 − 2.495 mm (0.0981 − 0.0982 in.)
2.495 − 2.498 mm (0.0982 − 0.0983 in.)
2.498 − 2.501 mm (0.0983 − 0.0985 in.)
2.501 − 2.504 mm (0.0985 − 0.0986 in.)
56.982 − 57.000 mm (2.2434 − 2.2441 in.)
56.745 − 56.755 mm (2.2341 − 2.2344 in.)
0.06 mm (0.0024 in.)
0.02 mm (0.0008 in.)
0.02 mm (0.0008 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1308 of 1399
SS1EP−01
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−7
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Distributor x Cylinder head1818013
No. 1 engine hanger x Cylinder head4142030
No. 2 engine hanger x Cylinder head4142030
Air intake chamber x Intake manifold2121015
Intake manifold x Cylinder head2121015
Heater inlet pipe x Intake manifold2121015
EGR pipe x Cylinder head2121015
EGR pipe x EGR valve Union nut7880058
Water outlet x Cylinder head2121015
Generator bracket x Cylinder head4344032
Cylinder head x Cylinder block 1st
2nd 3rd39
Turn 90°
Turn 90°400
Turn 90°
Turn 90°29
Turn 90°
Turn 90°
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head1616012
Camshaft timing gear x Camshaft7475054
Chain tensioner x Cylinder head2121015
Water bypass outlet x Cylinder head2121015
Heater pipe x Timing chain cover2121015
Heater pipe x Cylinder head2020014
Exhaust manifold x Cylinder head3940029
Heat insulator x Exhaust manifold1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission2424017
No. 1 support bracket clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
No. 2 water bypass pipe x Cylinder head2020014
No. 2 water bypass pipe x No. 1 engine hanger2020014
Fuel inlet hose x Fuel filter2930022
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
Oil dipstick guide x Intake manifold2020014
Oil dipstick guide x No. 1 oil pan2020014
PS reservoir tank x Air intake chamber2020014
Oil jet x Cylinder block2020014
Vibration damper x Cylinder block2020014
Chain tensioner slipper x Cylinder block6970051
Timing chain cover x Cylinder block2121015
Drive belt idler pulley x Timing chain cover4344032
Crankshaft pulley x Crankshaft4124,200304
Transmission housing x No. 1 oil pan7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1309 of 1399
SS−8
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
1996 LAND CRUISER (RM451U)
A/C compressor bracket x No. 1 oil pan
3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil check valve x Cylinder block2525018
Main bearing cap x Cylinder block
1st
2nd74
Turn 90°750
Turn 90°54
Turn 90°
Connecting rod cap x Connecting rod 1st
2nd48
Turn 90°490
Turn 90°35
Turn 90°
Rear oil seal retainer x Cylinder block2121015
Oil cooler cover x Cylinder block2121015
LH engine mounting bracket x Cylinder block6970051
LH insulator x LH engine mounting bracket7273043
RH engine mounting bracket x Cylinder brock6970051
RH insulator x RH engine mounting bracket7273043
PS pump x Cylinder block3637027
Knock sensor x Cylinder block4445033
Oil filter union x Cylinder block4445033
Drive plate x Crankshaft1001,00074
Transmission x Cylinder block7273053
Transmission x No. 1 oil pan7273053
Torque converter clutch x Drive plate5555041
A/T oil cooler pipe x Union (Transmission)3435025
Starter x Transmission3940029
Frame crossmember x Frame6162045
Frame crossmember x Engine rear mounting insulator7475054
Engine front mounting insulator x Frame7475054
Transfer shift lever x Transmission1818513
Transmission shift lever assembly x Body5.45548 in.·lbf
Transmission control rod x Control shaft lever131309
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Rear differential8890065
Rear propeller shaft x Transfer8890065
Stabillizer bar bracket mounting bolt1818513
Stabillizer bar x Axle carrier2526019
PS pressure hose x PS pump5657542
Rear TWC x Center pipe4040029
Center pipe x Tailpipe4040029
Heated oxygen sensor (Bank 1 sensor 1) x Front exhaust pipe2020014
Heated oxygen sensor (Bank 1 sensor 2) x Center pipe2020014
No. 2 support bracket x Frame18.518513
No. 3 support bracket x Frame18.518513
No. 4 support bracket x Frame18.518513
Exhaust pipe damper x Tailpipe19.519514
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1325 of 1399
SS1E7−01
SS−24
−
SERVICE SPECIFICATIONS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Valve body x Transmission case101007
Oil stainer x Valve body101007
Oil pan7.47565 in.·lbf
Drain plug x Oil pan2020515
Parking lock pawl bracket x Transmission case7.47565 in.·lbf
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Transfer8890065
Rear propeller shaft x Rear dif ferential8890065
Drive plate x Crankshaft981,00072
Torque converter clutch x Drive plate5555040
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x TWC3940029
Oil cooler pipe3435025
Transmission x Engine7173053
Exhaust pipe clamp1919514
Park/neutral position switch Nut
Bolt6.9 1370
13061 in.·lbf 9
No. 2 vehicle speed sensor5.45548 in.·lbf
Speedometer driven gear sleeve x Locking plate1616012
Starter mounting bolt3940029
Transfer shift lever1818513
Stabilizer bar bracket mounting bolt1818513
Engine under cover mounting bolt2829021
Exhaust pipe No. 1 support bracket x Torque converter clutch housing2424017
Crossmember x Frame6162045
Engine rear mounting x Crossmember7475054
Transmission shift lever assembly x Body5.45548 in.·lbf
Oil cooler mounting bolt1111 58
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1341 of 1399
SS1EJ−02
SS−40
−
SERVICE SPECIFICATIONS BODY ELECTRICAL
163
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL
SERVICE DATA
TURN SIGNAL FLASHER
Flashes/Minute60 − 120
SPEEDOMETER (USING A SPEEDOMETER)
Standard indication (mph)Allowable range (mph)
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
12011 8 − 132
TACHOMETER (ON− VEHICLE) DC 13.5 V 25°C (77° F)
Standard indication (RPM)Allowable range (RPM)
700630 − 770
1,000900 − 1,100
2,0001,875 − 2,125
3,0002,850 − 3,150
4,0003,850 − 4,150
5,0004,850 − 5,150
FUEL RECEIVER GAUGE
A − B85.5 − 105.5 Ω
A − C126 − 150 Ω
B − C90 − 110 Ω
FUEL SENDER GAUGE
Float position F: Approx. 15 mm ((0.59 in.)Approx. 3 Ω
Float position E: Approx. 200 (7.87 in.)Approx. 110 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE
A − B71 − 79 Ω
A − C117 − 141 Ω
B − C185 − 215 Ω
OIL PRESSURE RECEIVER GAUGE
Resistance40 − 48 Ω
CRUISE CONTROL SWITCH
Switch position OFFNo continuity
Switch position RESUME/ACCELApprox. 68 Ω
Switch position SET/COASTApprox. 198 Ω
Switch position CANCELApprox. 418 Ω
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2 kΩ
2 − 3Approx. 0.5 − 1.7 kΩ
Actuator control arm free play0 mm (0 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010