Terminal TOYOTA LAND CRUISER 1996 J80 Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1996 J80Pages: 1399, PDF Size: 41.35 MB
Page 604 of 1399
Q07465
SP2−
1
2E6
ECM
No. 2 Vehicle Speed Sensor SP2
+
4
EC2
5
V
V−G EC2 E682
V
V−G
Q08227
SP2+SP2−
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−167
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check vehicle speed value or resistance between terminals SP2+ and SP2− of
ECM.
When using OBD II scan tool or T OYOTA hand−held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect an OBD II scan tool or TOYOTA hand− held tes-
ter to the DLC3.
(c) Start the engine and turn the OBD II scan tool or T OYOTA
hand −held tester main switch ON.
CHECK:
Drive the vehicle and read vehicle speed value.
OK:
Vehicle speed matches tester speed value.
When not using OBD II scan tool or TOYOTA hand−held tes-
ter:
PREPARATION:
Disconnect the connector from the ECM.
CHECK:
Check the resistance between terminals SP2+ and SP2− of the
ECM.
OK:
Resistance: 560 − 680 Ω
OK Check and replace ECM.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 605 of 1399
Q08218D00179
DI−168
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check No. 2 vehicle speed sensor.
PREPARATION:
Remove the No. 2 vehicle speed sensor from the transmission.
CHECK:
(a) Measure the resistance between terminals 1 and 2 of the
vehicle speed sensor.
(b) Check the voltage between terminals 1 and 2 of the ve- hicle speed sensor when a magnet is put close to the front
end of the vehicle speed sensor then taken away quickly.
OK:
(a) Resistance: 560 − 680 Ω
(b) Voltage is generated intermittently.
HINT:
The generated voltage is extremely low.
NG Replace No. 2 vehicle speed sensor.
OK
Check and repair harness and connector be-
tween ECM and No. 2 vehicle speed sensor
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 607 of 1399
BE3840
Q08479D00090
ON
(−)
(+)
NSWR
2
L
Position
P, NR
D
2
L NSW
−
Body ground R −
Body ground 2 −
Body ground L −
Body ground
Below 1.5 V
7.5 − 14 V
7.5 −
14 V*
7.5 − 14 V
Below 1.5 V
Below 1.5 V
Below 1.5 V Below1.5 V
Below 1.5 V
Below 1.5 V Below1.5 V
Below 1.5 V
9 − 14 V
Below 1.5 V
Below 1.5 V
Below 1.5 V
9 −
14 V
9 − 14 V
9 − 14 V Below 1.5 V
DI−170
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Read PNP, REVERSE, 2ND and LOW signals.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Shift lever into the P, R, N, 2 and L positions, and read the PNP,
REVERSE, 2 and L signals on the TOYOTA hand −held tester.
OK:
Shift positionSignal
22ND OFF → ON
LLOW OFF → ON
RREVERSE OFF → ON
P, NPNP SW OFF → ON
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals NSW, 2 and L of ECM
and body ground when the shift lever is shifted to the following
positions.
OK:
*: The voltage will drop slightly due to lighting up of the back up
light.
OK Check and replace ECM.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 608 of 1399
Q07657D00109
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−171
1996 LAND CRUISER (RM451U)
2 Check park/neutral position switch.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the park/neutral position switch connector.
CHECK:
Check the continuity between each terminal shown below when
the shift lever is moved to each position.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
P4 − 75 − 6
R4 − 8−
N4 − 105 − 6
D4 − 9−
22 − 4−
L3 − 4−
NG Replace park/neutral position switch.
OK
Repair or replace harness and connector between battery and park/neutral posit\
ion switch, and
park/neutral position switch and ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 609 of 1399
Q07467
Cruise Control ECUOD OD1B+
G−O
9 18ECM
E7
BE3840
Q07658 D00091
ON
(−) (+) OD1
DI−172
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
O/D Cancel Signal Circuit
CIRCUIT DESCRIPTION
While driving with cruise control activated, in order to minimize gear shifting and provide\
smooth cruising on
an uphill, overdrive may be prohibited temporarily in some conditions.
The cruise control ECU sends O/D cut signals to the ECM as necessary and\
the ECM cancels overdrive
shifting until these signals are discontinued.
(For details, see the Cruise Control section, page DI−292)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminal OD1 of ECM and body ground.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal OD1 of the ECM and
body ground.
OK:
Voltage: 9 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
DI5L0−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 610 of 1399
BE3840
Q07660 D00015
ON
OD
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−173
1996 LAND CRUISER (RM451U)
2 Check voltage between terminal OD of cruise control ECU harness side connec-
tor and body ground.
PREPARATION:
(a) Disconnect the cruise control ECU connector.
(b) Turn ignition switch ON.
CHECK:
Measure the voltage between terminal OD of the cruise control
ECU harness side connector and body ground.
OK:
Voltage: 9 − 14 V
OK Check and replace cruise control ECU.
NG
3 Check harness and connector between cruise control ECU and ECM (See pag\
e IN−28 ).
NG Repair or replace wire harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 613 of 1399
BE3840
Q08230D00093
ON
OD2
DI−176
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check OVRDRIVE CUT SW2 signal.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Read the OVRDRIVE CUT SW2 signal on the TOYOTA hand −
held tester.
OK:
O/D Main SwitchOVRDRIVE CUT SW2 Signal
O/D ON (pushed in)OFF
O/D OFF (pushed out)ON
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Check the voltage between terminal OD2 of the ECM and body
ground.
OK:
O/D Main SwitchVoltage
O/D ON9 − 14 V
O/D OFFBelow 3 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−147 ).
NG
3 Check harness and connector between O/D OFF indicator light and ECM (Se\
e page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 614 of 1399
Q08233
Q08233
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−177
1996 LAND CRUISER (RM451U)
4 Check O/D main switch.
CHECK:
(a) Disconnect the O/D main switch connector.
(b) Measure the resistance between terminals 2 and 4 of the
O/D main switch connector.
OK:
O/D Main SwitchResistance
ON∞ Ω〈 open)
OFF0 Ω (continuity)
NG Replace O/D main switch.
OK
Check and replace the combination meter
(See page BE−32 ).
O/D OFF indicator light remains ON:
1 Check O/D main switch.
CHECK:
(a) Disconnect the O/D main switch connector.
(b) Measure the resistance between terminals 2 and 4 of the
O/D main switch connector.
OK:
O/D Main SwitchResistance
ON∞ Ω〈 open)
OFF0 Ω (continuity)
NG Replace O/D main switch.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 617 of 1399
BE3840
Q08229D00094
PWR
ON
DI−180
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check PATTERN SEL SW signal.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Read the PWR signal on the TOYOTA hand −held tester.
OK:
PWR Mode SwitchPATTERN SEL SW Signal
PWRON
NORMOFF
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal PWR of the ECM con-
nector and body ground when the PWR mode switch is set to
the PWR (POWER) position and NORM (NORMAL) position.
OK:
PWR Mode SwitchVoltage
PWR7.5 − 14 V
NORMBelow 1.5 V
HINT:
The ECM uses the normal pattern signal if the power signal is
not input.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 618 of 1399
Q08235
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−181
1996 LAND CRUISER (RM451U)
3 Check PWR mode switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check the resistance between terminals of the pattern select
switch connector when the PWR mode switch is set to PWR and
NORM positions.
OK:
PWR Mode SwitchResistance
PWR0 Ω (continuity)
NORM∞ Ω (open)
NG Replace pattern select switch.
OK
4 Check harness and connector between battery and pattern select switch, a\
nd pattern select switch and ECM (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010