Terminal TOYOTA LAND CRUISER 1996 J80 Workshop Manual

A00172
ON
THG E2 (+)(−)
BE6653
P24667
DI−76
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals of THG and E2 of ECM
connector.
HINT:
EGR gas temp. sensor connector is disconnected.
OK:
Voltage: 4.5 − 5.5 V
OK Open in harness between terminals E2 or THG. Repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
4 Check connection of vacuum hose, EGR hose (See page EC−11).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00173
ON
EGR ONOFF
(1) VSV is ON:
(2) VSV is OFF: Air
GE
Air GE
BE6653
P22905
P22963
P22964
−
DIAGNOSTICS ENGINE
DI−77
1996 LAND CRUISER (RM451U)
5 Check the VSV for EGR.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Check VSV function.
(1) Connect between terminal EGR of ECM and bodyground (ON).
(2) Disconnect between terminal EGR of ECM and
body ground (OFF).
OK:
(1) VSV is ON:
Air does not flow from pipe G to pipe E.
(2) VSV is OFF:
Air from pipe G is flows out through pipe E.
OK Go to step 7.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24665
DI−82
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check the VSV for EGR (See page DI−69 ).
OK Check EGR valve (See page EC−11).
NG
5 Check operation of the VSV for EGR (See page SF−60).
NG Replace VSV for EGR.
OK
Check for short in harness and connector
between VSV and ECM (See page IN−28).
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check resistance of EGR gas temp. sensor (See page DI−105).
PREPARATION:
Disconnect EGR gas temp. sensor connector.
CHECK:
Measure resistance between terminals of EGR gas temp. sen-
sor connector.
OK:
Resistance: 2.5 k Ω or more
(Not immediately after driving)
HINT:
If there is short circuit, ohmmeter indicates 200 Ω or less.
NG Replace EGR gas temp. sensor.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00176
ONSPD
(+)
(−)
BE6653
P24668
AT7809
9 − 14 V
0
Turn the wheel
DI−88
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of speedometer.
CHECK:
Drive the vehicle and check if the operation of the speedmeter in the co\
mbination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer displa\
y is normal.
NG Check speedometer circuit (See page BE−2 ).
OK
2 Check voltage between terminal SPD of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Disconnect cruise control ECU connector.
(c) Shift the shift lever to neutral.
(d) Jack up a rear wheels on one side.
(e) Turn ignition switch ON.
CHECK:
Measure voltage between terminal SPD of ECM connector and
body ground when the wheel is turned slowly.
OK:
Voltage is generated intermittently.
NG Check and repair harness and connector between combination meter and ECM.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22474
EBBR
22 22
1 3
4
2 2
2
R−Y R/B No.2
From BatteryR
Y−R
EA2
EB1
Y−RY −R
Y−R R
R−G
R−B
G−Y
Y−L
4
1
3 6
IAC Valve MRLY
E7
E4
E4
E4
E4 7 3
6
5
4
ISC1
ISC2
ISC3
ISC4 B+
E01
E01
E01
E01
EFI
2
5
EFI Main
Relay
7
1 ECM
A00202
ISC1
ISC2
ISC3
ISC4 A/C Switch OFF
→ ON
(IAC Valve Open)
20 V/Division
10 msec./Division
ISC1
ISC2
ISC3
ISC4 20 V/
Division
10 msec./Division
(IAC Valve Close)
A/C Switch ON →
OFF
FI6536
FI6537
DI−90
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Reference: INSPECTION USING OSCILLOSCOPE
With the engine idling measure wavefoms between terminals
ISC1, ISC2, ISC3, ISC4 and E01 of ECM when A/C switch ON
or OFF.
HINT:
The correct waveforms are as shown.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00178
ONISC1 ISC3ISC2 ISC4
E4 connector
(−) (+)
BE6653
P24669
−
DIAGNOSTICS ENGINE
DI−91
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check air induction system (See page SF−1 ).
NG Repair or replace.
OK
2 Check voltage terminals ISC1, ISC2, ISC3, ISC4, of ECM connector and bod\
y ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Disconnect the E4 connector of ECM.
(c) Turn ignition switch ON.
CHECK:
Measure voltage between terminals ISC1, ISC2, ISC3, ISC4 of
ECM connector and body ground.
OK:
Voltage: 9 − 14 V
OK Go to step 4.
NG
3 Check IAC valve (See page SF−49 ).
NG Replace IAC valve.
OK
Check for open and short in harness and co −nnector between EFI main relay (Marking:EFI) and
IAC valve and ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00203
CloseOpen Battery
Battery
B1
S1
S2 B2S4
S3
B1
S1 S2 B2S4S3
P24670
P24671
DI−92
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check operation of the IAC valve .
PREPARATION:
Remove IAC valve (See page SF−51).
CHECK:
(a) Connect the positive (+) leak from the battery to terminals
5 (B1) and 2 (B2), and the negative ( −) lead to terminals
4 (S1), −1 (S2), −6 (S3), −3 (S4) in that order.
(b) Connect the positive (+) lead from the battery to terminals
5 (B1) and 2 (B2), and the negative ( −) lead to terminals
3 (S4), − 6 (S3), −1 (S2), − 4 (S1) in that order.
OK:
(1) The valve moves to close direction.
(2) The valve moves to open direction.
HINT:
The ACTIVE TEST mode of the T OYOTA hand−held tester can
be used to change the step of the IAC valve as desired.
NG Repair or replace IAC valve.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6653
FI7058A00486
Throttle Position
SensorON
4
3
21
1
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2 E112V
5V
FI7064
A00487
Throttle Position Sensor
4
3
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2 E112V
5V
IDL E2
ON
DI−94
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Connect sensor wire harness terminals between terminals 1 and 2.
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: ON
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Connect between terminals IDL and E2 of ECM.
HINT:
Throttle position sensor connector is disconnected.
Before checking, do a visual check and contact pressure check
for connector (See page IN−28).
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: ON
OK Open in harness between ECM and throttle position sensor, repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00492
43
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2E1 12V
5V
ON
Throttle Position Sensor
DI−96
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check for open and short in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals 1 and 2 of throttle position
sensor connector.
OK:
Voltage: 9 − 14 V
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
2 Check for open and short in harness and connector between throttle posit\
ion sensor and ECM (See page IN−28).
NG Open or short in harness between ECM and
throttle position sensor.
OK
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00183
ON(+)
(−)IGF
BE6653
P24673
DI−98
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check for spark (See page IG−1).
NG Go to step 4.
OK
2 Check for open and short in harness and connector in IGF signal circuit \
between ECM and igniter (See page IN−28).
NG Repair or replace harness or connector.
OK
3 Disconnect igniter connector and check voltage between terminal IGF of E\
CM connector and body ground.
PREPARATION:
(a) Disconnect igniter connector.
(b) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(c) Turn ignition switch ON.
CHECK:
Measure voltage between terminal IGF of ECM connector and
body ground.
OK:
Voltage: 4.5 − 5.5 V
OK Replace igniter.
NG
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010