Relay TOYOTA LAND CRUISER 1996 J80 User Guide

Z19533
1
2
3
4
5 12
3
4
5
AC2SE−03
AC−64
−
AIR CONDITIONING HEATER MAIN RELAY
1391
Author: Date:
1996 LAND CRUISER (RM451U)
HEATER MAIN RELAY
INSPECTION
INSPECT HEATER MAIN RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 3
2 − 4Continuity
Apply B+ between
terminals 3 and 5.4 − 5Continuity
If continuity is not as specified, replace the relay.
BE1850 BElS44
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z09804
1
23
4
5
6
1
3
6 2
4
AC2SF−01
−
AIR CONDITIONING REAR HEATER RELAY
AC−65
1392
Author: Date:
1996 LAND CRUISER (RM451U)
REAR HEATER RELAY
INSPECTION
INSPECT REAR HEATER RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant2 − 6
1 − 3Continuity
Apply B+ between
terminals 2 and 6.1 − 4Continuity
If continuity is not as specified, replace the relay.
H-8-2BE1844
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z09507
1
2
3
4 412
4
3AC2SG−01
AC−66
−
AIR CONDITIONING MAGNETIC CLUTCH RELAY
1393
Author: Date:
1996 LAND CRUISER (RM451U)
MAGNETIC CLUTCH RELAY
INSPECTION
INSPECT MAGNETIC CLUTCH RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 3 Continuity
Apply B+ between
terminals 1 and 3.2 − 4Continuity
If continuity is not as specified, replace the relay.BE1647BE1841
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N06549
AC2SH−01
V02084OFFON
103 °C (217° F)
108
°C (226° F)
−
AIR CONDITIONING ENGINE COOLANT TEMPERATURE (ECT) CUT
RELAYAC−67
1394
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE COOLANT
TEMPERATURE (ECT) CUT RELAY
INSPECTION
INSPECT SWITCH CONTINUITY
Check the continuity betweeen terminals of the switch, as
shown in the chart below.
If continuity is not as specified, replace the switch.
_tf
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LT−01
BE−2
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
SymptomSuspect AreaSee page
Ignition switch is not set to each position.5. Ignition SwitchBE−11
”Key unlock warning system” does not operate.
1. GAUGE Fuse (I/P F/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light up. (Taillight is normal.)
1. Headlight Bulb
2. MAIN FL
3. HEAD (LH) Fuse (No.2 R/B)
4. HEAD (RH) Fuse (No.2 R/B)
5. Light Control Switch
6. Headlight Dimmer Switch
7. Wire Harness−
−
−
−
BE−14
BE−14
−
Headlight does not light up. (Taillight does not light up.)
1. Headlight Bulb
2. Light Control Switch
3. Headlight Dimmer Switch
4. Wire Harness−
BE−14
BE−14 −
Only one light comes ON.
1. Headlight Bulb
2. HEAD (LH) Fuse (No.2 R/B)
3. HEAD (RH) Fuse (No.2 R/B)
4. Wire Harness−
−
−
−
”Lo− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Hi− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Flash” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
Taillight does not light up. (Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (I/P F/B)
3. Light Control Switch
4. Taillight Control Relay (No.2 R/B)
5. Wire Harness−
−
BE−14
BE−14 −
Taillight does not light up. (Headlight does not light up.)
1. Taillight Bulb
2. MAIN FL
3. TAIL Fuse (I/P F/B)
4. Light Control Switch
5. Wire Harness−
−
−
BE−14 −
Headlight and Taillight does not light.1. Light Control Switch
2. Wire HarnessBE−14
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−3
1996 LAND CRUISER (RM451U)
Only one side taillight does not light.
1. Taillight Bulb
2. Wire Harness−
−
Taillight does not light.
(Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (No.2 R/B)
3. Taillight Control Relay (No.2 R/B)
4. Light Control Switch
5. Wire Harness−
BE−14
BE−14
BE−14 −
TURN SIGNAL AND HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
”Hazard” and ”Turn” do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher (No.1 R/B)
3. Wire HarnessBE−19
BE−19
−
None of blinks for hazard. (Turn is normal.)
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Hazard warning light does not light up. (Turn is normal.)1. HAZ − HORN Fuse (No.2 R/B)
2. Wire HarnessBE−19 −
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE−19−
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE−19−
Only one bulb does not light up for hazard turn.1. Bulb
2. Wire Harness−
−
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (I/P F/B)
3. Turn Signal Switch
4. Wire HarnessBE−11
BE−19
BE−19 −
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (I/P F/B)
2. Turn Signal Switch
3. Wire HarnessBE−19
BE−19−
INTERIOR LIGHT SYSTEM
SymptomSuspect AreaSee page
Room light does not light up.
1. DOME Fuse (No.2 R/B)
2. Door Courtesy Switch
3. Front Personal Light
4. Room Light Assembly
5. Bulb
6. Wire Harness−
BE−21
BE−21
BE−21 −
−
Room light remains always on.1. Door Courtesy Switch
2. Wire HarnessBE−21
−
BACK −UP LIGHT SYSTEM
SymptomSuspect AreaSee page
Back−Up light does not light up.
1. GAUGE Fuse (I/P F/B)
2. Ignition Switch
3. Park/Neutral Position Switch (A/T)
4. Bulb
5. Wire Harness−
BE−11 −
−
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−4
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Back−
Up light remains on.
1. Park/Neutral Position Switch (A/T)
2. Wire Harness−
−
Only one light does not light up.1. Bulb
2. Wire Harness−
−
STOP LIGHT SYSTEM
SymptomSuspect AreaSee page
Stop light does not light up.
1. STOP Fuse (I/P F/B)
2. Stop Light Switch
3. Bulb
4. Wire Harness−
BE−25 −
−
Stop light remains always on.1. Stop Light Switch
2. Wire HarnessBE−25−
Only one light does not light up.1. Wire Harness
2. Bulb−
−
WIPER AND WASHER SYSTEM
SymptomSuspect AreaSee page
Wipers do not operate or return to off position.
1. WIPER Fuse (I/P F/B)
2. Wiper Switch
3. Wiper Motor
4. Wiper Relay
5. Wire HarnessBE−27
BE−27
BE−27
BE−27
−
Wipers do not operate in MIST.
1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire HarnessBE−27
BE−27
BE−27
−
Wipers do not operate in INT.
1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire HarnessBE−27
BE−27
BE−27−
Washer does not operate.
1. Washer Hose or Nozzle Clogged
2. Washer Switch
3. Washer Motor
4. Wire Harness−
BE−27
BE−27 −
METER, GAUGES AND ILLUMINATION:
COMBINATION METER
SymptomSuspect AreaSee page
Tachometer, speedometer, engine coolant temperature gauge and
fuel gauge do not operate.1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Speedometer does not operate.
1. No.1 Vehicle Speed Sensor
2. Speedometer Driven Gear and Drive Gear
3. Meter Circuit
4. Wire HarnessBE−34−
BE−32 −
Tachometer does not operate.
1. Meter Circuit
2. Igniter
3. Wire HarnessBE−32−
−
Tachometer does not operate.
1. Meter Circuit
2. Igniter
3. Wire HarnessBE−32−
−
Voltmeter does not operate.1. Voltmeter Receiver Gauge
2. Wire HarnessAT −6
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−5
1996 LAND CRUISER (RM451U)
Fuel gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32
−
Engine coolant temperature gauge does not operation or
abnormal operate.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32−
Oil pressure gauge does not operate or abnormal operation.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−34−
All illumination lights do not light up.
1. TAIL Fuse (I/P F/B)
2. Light Control Rheostat
3. Wire Harness−
BE−34 −
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up.1. Bulb
2. Wire Harness−
−
WARNING LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
Warning lights do not lights up.
(Except discharge, SRS and door open)1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Brake warning light does not light up.
1. Bulb
2. Brake Fluid Level Switch
3. Parking Brake Switch
4. Meter Circuit
5. Wire Harness−
BE−34
BE−34
BE−32 −
Open door warning light does not light up.
1. Bulb
2. Door Courtesy Switch
3. DOME Fuse (No.2 R/B)
4. Meter Circuit
5. Wire Harness−
BE−21
BE−21 −
−
−
SRS warning light does not light up
1. Bulb
2. Airbag Sensor Assembly
3. ECU− B Fuse (I/P F/B)
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Discharge warning light does not light up.
1. Bulb
2. IGN Fuse (No.1 J/B)
3. Generator
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Seat belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Seat Belt Warning Relay (I/P F/B)
4. Meter Circuit
5. Wire Harness−
BE−34 −
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−7
1996 LAND CRUISER (RM451U)
DEFOGGER SYSTEM
SymptomSuspect AreaSee page
Defogger system does not operate.
1. DEFOG Fuse (I/P F/B)
2. GAUGE Fuse (I/P F/B)
3. Defogger Switch
4. Defogger Relay (No.1 R/B)
5. Defogger Wire
6. Wire Harness−
−
BE−43
BE−43 −
−
POWER WINDOW CONTROL SYSTEM
SymptomSuspect AreaSee page
Power window does not operate (ALL).
(Power door lock does not operate.)
1. POWER Fuse (I/P F/B)
2. GAUGE Fuse (I/P F/B)
3. Power Main Relay (No.1 R/B)
4. Wire Harness−
−
−
−
Power window does not operate (ALL).
(Power door lock is normal.)
1. Ignition Switch
2. Power Main Relay (No.1 R/B)
3. Power Window Master Switch
4. Wire HarnessBE−11
−
BE−46 −
”One touch power window system” does not operate.1. Power Window Master SwitchBE−46
Only one window glass does not operate.
1. Power Window Master Switch
2. Power Window Switch
3. Power Window Motor
4. Wire HarnessBE−46
BE−46
BE−46−
POWER DOOR LOCK CONTROL SYSTEM
SymptomSuspect AreaSee page
Power door lock control system does not operate (ALL).
1. POWER Fuse (I/P F/B)
2. Power Main Relay (No.1 R/B)
3. Wire Harness−
−
−
Power door lock control system does not operate by door lock
control switch.1. Door Lock Control Switch
2. Power Main Relay (No.1 R/B)
3. Wire HarnessBE−51
−
−
Power door lock control system does not operate by door key.
1. Door Key Lock and Unlock Switch
2. Power Main Relay (No.1 R/B)
3. Wire HarnessBE−11−
−
Only one door does not operate.
1. Door Lock Motor
2. Door Lock Link Disconnected
3. Wire HarnessBE−51 −
−
Fault in key confine prevention operation.
1. Power Main Relay (No.1 R/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
SLIDING ROOF SYSTEM
SymptomSuspect AreaSee page
Sliding roof system does not operate.
(Door lock does not operate.)
1. GAUGE Fuse (I/P F/B)
2. Ignition Switch
3. POWER Fuse (No.1 J/B)
4. Power Main Relay (No.1 R/B)
5. Sliding Roof Control Switch
6. Sliding Roof Control Relay
7. Sliding Roof Motor
8. Wire Harness−
BE−11 −
−
BE−58
BE−58
BE−58
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−8
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Sliding roof system operates abnormally.
1. Limit Switch
2. Sliding Roof Control Switch
3. Sliding Roof Control RelayBE−58
BE−58
BE−58
Sliding roof system stops operation half way.
1. Sliding Roof Control Relay
2. Sliding Roof Limit Switch
3. Sliding Roof Control Switch
4. Sliding Roof Motor
(Stones to foreign material trapped in motor assembly)BE−58
BE−58
BE−58
BE−58
”Key−off sliding roof” operation does not operate.
1. POWER Fuse (I/P F/B)
2. Door Lock Control Relay
3. GAUGE Fuse (I/P F/B)
4. Ignition Switch
5. Door Courtesy Switch
6. Wire Harness−
BE−51 −
BE−11
BE−21
−
POWER MIRROR SYSTEM
SymptomSuspect AreaSee page
Power mirror system does not operate.
1. CIG Fuse (I/P J/B)
2. Mirror Control Switch
3. Mirror Motor
4. Wire Harness−
BE−69
BE−69 −
Power mirror operate abnormally.
1. Mirror Control Switch
2. Mirror Motor
3. Wire HarnessBE−69
BE−69−
POWER SEAT CONTROL SYSTEM
SymptomSuspect AreaSee page
Power seat does not operate.
1. POWER Fuse (I/P F/B)
2. Power Seat Switch
3. Wire Harness−
BE−62 −
”Sliding operation” does not operate.
1. Slide Motor
2. Power Seat Switch
3. Wire HarnessBE−62
BE−62−
”Reclining operation” does not operate.
1. Reclining Motor
2. Power Seat Switch
3. Wire HarnessBE−62
BE−62−
”Rear vertical operation” does not operate.
1. Rear Vertical Motor
2. Power Seat Switch
3. Wire HarnessBE−62
BE−62−
”Lumber support operation” does not operate.
1. Lumber Support Motor
2. Lumber Support Switch
3. Wire HarnessBE−62
BE−62−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010