Spark TOYOTA LAND CRUISER 1996 J80 User Guide

EM0494
−
ENGINE MECHANICAL VALVE CLEARANCE
EM−7
510
Author: Date:
1996 LAND CRUISER (RM451U)
9. Rear valves of No. 6 cylinder
ADJUST VALVE CLEARANCE
(a) Remove the distributor (See page IG−10).
(b) Remove the camshafts (See page EM−28).
(c) Remove the adjusting shim with a small screwdriver.
(d) Determine the replacement adjusting shim size by follow- ing the Formula or Charts:
Using a micrometer, measure the thickness of the
removed shim.
Calculate the thickness of a new shim so that the
valve clearance comes within specified value.
T ....... Thickness of removed shim
A ....... Measured valve clearance
N ....... Thickness of new shim
Intake: N = T + (A − 0.20 mm (0.008 in.))
Exhaust: N = T + (A − 0.30 mm (0.012 in.))
Select a new shim with a thickness as close as pos-
sible to the calculated value.
HINT:
Shims are available in 17 sized in increments of 0.05 mm
(0.0020 in.), from 2.50 mm (0.0984 in.) to 3.30 mm (0.1299 in.).
(e) Place a new adjusting shim on the valve lifters.
(f) Install the camshafts (See page EM−54 ).
(g) Recheck the valve clearance.
(h) Install the distributor (See page IG−11 ).
10. REINSTALL CYLINDER HEAD COVER
(a) Install the gasket to the cylinder head cover.
(b) Install the cylinder head cover with the 13 bolts.
11. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS (See page IG−1 )
12. RECONNECT HEA TER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the ground strap and engine wire with the 2 bolts.
13. REINSTALL THROTTLE BODY (See page SF−48 )
14. REFILL RADIATOR WITH ENGINE COOLANT
15. CHECK AND ADJUST IGNITION TIMING (See page EM−10 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P08374A16075
1 Dot Mark
EM−32
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
30. REMOVE CYLINDER HEAD COVER
Remove the 13 bolts, cylinder head cover and gasket.
31. REMOVE SPARK PLUGS
32. SET NO. 1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley and align its groove with the ”0”
mark on the timing chain cover.
(b) Check that the timing marks (1 and 2 dots) of the camshaft
drive and driven gears are in straight line on the cylinder
head surface as shown in the illustration.
If not, turn the crankshaft 1 revolution (360° ) and align the
marks as above.
33. REMOVE CHAIN TENSIONER
Remove the 2 nuts, chain tensioner and gasket.
34. REMOVE CAMSHAFT TIMING GEAR
(a) Remove the semi−circular plug.
(b) Place the matchmarks on the camshaft timing gear and timing chain.
(c) Hold the intake camshaft with a wrench, remove the bolt and distributor gear.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−50
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
2. REPLACE SPARK PLUG TUBE GASKETS
(a) Using a screwdriver, pry out the tube gasket.
(b) Using SST and a hammer, tap in a new tube gasket as
shown in the illustration.
SST 09950 −60010 (09951 −00480), 09950 −70010
(09951 −07150)
(c) Apply a light coat of MP grease to the gasket lip.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E6−01
−
ENGINE MECHANICAL CYLINDER HEAD
EM−51
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Thoroughly clean all parts to be assembled.
Before installing the parts, apply new engine oil to all slid-
ing and rotating surfaces.
Replace all gaskets and oil seals with new ones.
1. INSTALL SPARK PLUG TUBES
HINT:
When using a new cylinder head, spark plug tubes must be
installed.
(a) Mark the standard position away from the edge, onto the spark plug tube.
Standard protrusion: 45.5 mm (1.791 in.)
(b) Apply adhesive to the spark plug tube hole of the cylinder
head.
Sealant:
Part No. 08833−00070, Adhesive 1324, THREE BOND
1324 or equivalent
(c) Using a press, press in a new spark plug tube until there is 45.5 mm (1.791 in.) protruding from the camshaft bear-
ing cap installation surface of the cylinder head.
NOTICE:
Avoid pressing a new spark plug tube in too far by measur-
ing the amount of protrusion while pressing.
2. INSTALL TVV
(a) Apply adhesive to 2 or 3 threads of the TVV. Adhesive:
Part No.08833 −00080, THREE BOND 1344, LOCTITE
242 or equivalent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Front Mark
P09890
Push
P08374A16075
1 Dot Mark
−
ENGINE MECHANICAL CYLINDER HEAD
EM−59
1996 LAND CRUISER (RM451U)
6. INSTALL CHAIN TENSIONER
(a) Place a new gasket so that the front mark is toward the
front side.
(b) Push the tensioner by hand until it touches the head installation surface, then install the 2 nuts.
(c) Tighten the 2 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
7. CHECK VALVE TIMING
(a) Turn the crankshaft pulley, and align its groove with the timing mark ”0” of the timing chain cover.
NOTICE:
Always turn the crankshaft clockwise.
(b) Check that the timing marks (1 and 2 dots) of the camshaft
drive and driven gears are in straight line on the cylinder
head surface as shown in the illustration.
If not, turn the crankshaft 1 revolution (360° ) and align the
marks as above.
8. CHECK AND ADJUST VALVE CLEARANCE (See page
EM−4)
Turn the camshaft and position the cam lobe upward and check
and adjust the valve clearance.
Valve clearance (Cold):
Intake0.15 − 0.25 mm (0.006 − 0.010 in.)
Exhaust0.25 − 0.35 mm (0.010 − 0.041 in.)
9. INSTALL SPARK PLUGS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0IB−02
SPARK TEST
TRY ANOTHER IGNITERNO
OK
OK
OK
OK
OK
BAD
BAD
BAD
BAD
BAD
BADConnect securely.
Replace the cord(s).
Replace the distributor housing assembly.
Check wiring between ECM, ignition coil and
igniter, and then try another ECM.
CHECK CONNECTION OF IGNITION COIL, IGNITER AND
DISTRIBUTOR CONNECTOR
CHECK RESISTANCE OF HIGH−
TENSION CORD
(See step 8)
Maximum resistance: 25 k Ω per cord
CHECK RESISTANCE OF IGNITION COIL (See step 24)
Resistance: Cold Hot
Primary 0.36 − 0.55 Ω 0.45 − 0.65 Ω
Secondary 9.0 − 15.4 kΩ 11.4 − 18.1 kΩ
CHECK AIR GAP OF DISTRIBUTOR (See step 31)
Air gap: 0.2 − 0.4 mm (0.008 −0.016 in.)
OK
CHECK RESISTANCE OF SIGNAL GENERATOR
(PICKUP COIL) (See step 32)
Resistance: Cold Hot
G1 and G− 185 − 275 Ω 240 − 325 Ω
G2 and G− 185 − 275 Ω 240 − 325 Ω
NE and G − 185 − 275 Ω 240 − 325 Ω
CHECK IGT SIGNAL FROM ECM
(See page DI−93 ) Check
wiring between ignition switch to ignition
coil and igniter.
Replace the ignition coil.
Replace the distributor housing assembly.
BAD
OK
CHECK
POWER SUPPLY TO IGNITION COIL AND IGNITER
1. Turn ignition switch to ON.
2. Check that there is battery voltage at ignition coil positive (+)
terminal.
−
IGNITION IGNITION SYSTEM
IG−1
735
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION SYSTEM
ON−VEHICLE INSPECTION
1. CHECK THAT SPARK OCCURS
(a) Disconnect the high −tension cords (from the ignition coil)
from the distributor cap.
(b) Hold the end approx. 12.5 mm (0.50 in.) from the body ground.
(c) Check if spark occurs while engine is being cranked.
HINT:
To prevent gasoline from being injected from injectors during
this test, crank the engine for no more than 1 − 2 seconds at a
time.
If the spark does not occur, do the test as follows:
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22687
P08512
IG−2
−
IGNITION IGNITION SYSTEM
736
Author: Date:
1996 LAND CRUISER (RM451U)
2. REMOVE NO.2 PCV HOSE
3. REMOVE AIR CLEANER HOSE
4. DISCONNECT THROTTLE CABLE
5. REMOVE NO.2 AND NO.3 CYLINDER HEAD COVERS
Remove the 4 bolts and head covers.
6. DISCONNECT HIGH −TENSION CORDS FROM SPARK
PLUGS
(a) Remove the 2 mounting bolts of the No.1 and No.2 cord clamps.
(b) Disconnect the high −tension cords at the rubber boot.
Do not pull on the cords.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside.
7. DISCONNECT HIGH−TENSION CORDS FROM DIS- TRIBUTOR CAP AND IGNITION COIL
(a) Using a screwdriver, lift up the lock claw and disconnect
the holder from the distributor cap (ignition coil).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG−4
−
IGNITION IGNITION SYSTEM
738
Author: Date:
1996 LAND CRUISER (RM451U)
NOTICE:
Check that the holder is correctly installed to the grommet
and distributor cap as shown in the illustration.
(c) Check that the lock claw of the holder is engaged by lightly
pulling the holder.
10. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS
(a) Secure the high −tension cords with the cord clamps as
shown in the illustration.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0152
P03783
−
IGNITION IGNITION SYSTEM
IG−5
739
Author: Date:
1996 LAND CRUISER (RM451U)
(b) Install the No.1 and No.2 cord clamps with the 2 bolts.
11. INSTALL NO.2 AND NO.3 CYLINDER HEAD COVERS
Install the head covers with the 4 bolts.
12. CONNECT THROTTLE CABLE
13. INSTALL AIR CLEANER HOSE
Install the air cleaner hose with the 2 clamp bolts.
14. INSTALL NO.2 PCV HOSE
15. DISCONNECT HIGH −TENSION CORDS FROM SPARK
PLUGS
16. REMOVE SPARK PLUGS
Using a 16 mm plug wrench, remove the spark plug.
17. CLEAN SPARK PLUGS
Using a spark plug cleaner or wire brush, clean the spark plug.
18. VISUALLY INSPECT SPARK PLUGS
Check the spark plug for electrode wear, threads damage and
insulator damage.
If abnormal, replace the plugs. Recommended spark plugs:
ND: K16R −U
NGK: BKR5EYA
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03792
IG−6
−
IGNITION IGNITION SYSTEM
740
Author: Date:
1996 LAND CRUISER (RM451U)
19. ADJUST ELECTRODE GAP
Carefully bend the outer electrode to obtain the correct elec-
trode gap.
Correct electrode gap: 0.8 mm (0.031 in.)
20. INSTALL SPARK PLUGS
Using a 16 mm plug wrench, install the spark plug. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
21. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the coils themselves. ”Cold” is from −10° C
(14 °F) to 50° C (122°F) and ”Hot” is from 50 °C (122° F) to
100 °C (212 °F).
22. DISCONNECT IGNITION COIL CONNECTOR
23. DISCONNECT HIGH−TENSION CORD
24. INSPECT PRIMARY COIL RESISTANCE
Using an ohmmeter, measure the resistance between the posi-
tive (+) and negative (−) terminals. Primary coil resistance:
Cold: 0.36 − 0.55 Ω
Hot: 0.45 − 0.65 Ω
If the resistance is not as specified, replace the ignition coil.
25. INSPECT SECONDARY COIL RESISTANCE
Using an ohmmeter, measure the resistance between the posi-
tive (+) and high −tension terminals.
Secondary coil resistance:
Cold: 9.0 − 15.4 kΩ
Hot: 11.4 − 18.1 kΩ
If the resistance is not as specified, replace the ignition coil.
26. RECONNECT HIGH−TENSION CORD
27. RECONNECT IGNITION COIL CONNECTOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010