check engine light TOYOTA LAND CRUISER 1996 J80 User Guide

BR2237
BR1NM−01
BR2238
−
BRAKE BRAKE BOOSTER ASSEMBLY
BR−17
999
Author: Date:
1996 LAND CRUISER (RM451U)
BRAKE BOOSTER ASSEMBLY
OPERATION
1. OPERATING CHECK
(a) Depress the brake pedal several times with the engine off
and check that there is no change in the pedal reserve
distance.
(b) Depress the brake pedal and start the engine. If the pedal
goes down slightly, operation is normal.
2. AIR TIGHTNESS CHECK
(a) Start the engine and stop it after 1 or 2 minutes. Depress
the brake pedal several times slowly. If the pedal goes
down furthest the 1st time, but gradually rises after the
2nd or 3rd time, the booster is air tight.
(b) Depress the brake pedal while the engine is running, and
stop the engine with the pedal depressed. If there is no
change in the pedal reserve travel after holding the pedal
for 30 seconds, the booster is air tight.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03788
CORRECT WRONG
Clearance
Z00038
Nippondenso Borroughs
−
CHARGING CHARGING SYSTEM
CH−3
1996 LAND CRUISER (RM451U)
(b) Check the fusible link and fuses for continuity.
Fusible link
MAIN 2.0 A
AM1 1.25 B
AM2 0.3 P
H−fuseAM1 50 A
FuseIGN 7.5 A
GAUGE 15 A
3. INSPECT DRIVE BELTS
(a) Visually check the drive belt for cracks, oiliness or wear.
Check that the belt does not touch the bottom of the pulley
groove.
If necessary, replace the drive belts as a set.
(b) Using a belt tension gauge, measure the belt tension. Belt tension gauge:
Nippondenso BTG−20 (95506 −00020)
Borroughts No. BT−33−73F
Drive belt tension:
New belt400 − 580 N (41.0 − 59.1 kgf, 90.4 − 130.2 lbf)
Used belt200 − 390 N (20.4 − 40.0 kgf, 45.0 − 88.2 lbf)
If the belt tension is not as specified, adjust it.
HINT:
”New belt” refers to a belt which has been used less than
5 minutes on a running engine.
”Used belt” refers to a belt which has been used on a run-
ning engine for 5 minutes or more.
After installing a new belt, run the engine for about 5 min-
utes and recheck the belt tension.
4. VISUALLY CHECK GENERATOR WIRING AND LIS- TEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) Check that there is no abnormal noise from the generator
while the engine is running.
5. INSPECT DISCHARGE WARNING LIGHT CIRCUIT
(a) Turn the ignition switch ”ON”. Check that the discharge warning light comes on.
(b) Start the engine. Check that the light goes off.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH−4
−
CHARGING CHARGING SYSTEM
1996 LAND CRUISER (RM451U)
If the light does not operate as specified, troubleshoot the dis-
charge warning light circuit.
6. INSPECT CHARGING CIRCUIT WITHOUT LOAD
HINT:
If a battery/generator tester is available, connect the tester to
the charging circuit as per the manufacturer’s instructions.
(a) If a tester is not available, connect a voltmeter and amme-
ter to the charging circuit as follows:
Disconnect the wire from terminal B of the generator
and connect it to the negative ( −) lead of the amme-
ter.
Connect the positive (+) lead of the ammeter to ter-
minal B of the generator.
Connect the positive (+) lead of the voltmeter to ter-
minal B of the generator.
Ground the negative ( −) lead of the voltmeter.
(b) Check the charging circuit as follows:
With the engine running from idle to 2,000 rpm, check the
reading on the ammeter and voltmeter.
Standard amperage 10 A or less
Standard voltage:
at 25° C ’(77°F)14.0 − 15.0 V
at 115°C ’(239° F)13.5 − 14.3 V
If the voltmeter reading is more than standard voltage, replace
the voltage regulator.
If the voltmeter reading is less than the standard voltage, check
the voltage regulator and generator as follows:
With terminal F grounded, start the engine and
check the voltmeter reading of terminal B.
If the voltmeter reading is more than standard volt-
age, replace the voltage regulator.
If the voltmeter reading is less than standard volt-
age, check the generator.
7. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater blower switch at
”HI”.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OT−01
ENGINE CONTROL SYSTEM Check Sheet
Customer’s Name
Driver’s Name
Data Vehicle
Brought in
License No.
Model and Model
Year
Frame No.
Engine Model
Odometer Reading
km
miles
Problem Symptoms
Engine does
not Start
Difficult to
Start
Poor Idling
Poor
Driveability
Engine Stall
Others
Engine does not crankNo initial combustionNo complete combustion
Engine cranks slowly
Other
Incorrect first idleIdling rpm is abnormalHigh ( rpm)Low ( rpm)
Rough idling
Other
HesitationBack fireMuffler explosion (after− fire)Surging
Knocking
Other
Soon after startingAfter accelerator pedal depressed
After accelerator pedal released
During A/C operation
Shifting from N to D
Other
Datas Problem
Occurred
Problem Frequency
Condition When
Problem Occurs
Weather
Engine Operation
Engine T emp.
Place Outdoor
Temperature Constant
Sometimes ( times per day/month)Once only
Other
Fine
CloudyRainySnowyVarious/Other
Hot
Warm CoolCold (approx. °F/ °C)
Highway
SuburbsInner CityUphillDownhill
Rough road
Other
Cold
Warming upAfter Warming upAny temp.Other
Starting
Just after starting ( min.)IdlingRacing
Driving
Constant speedAccelerationDeceleration
A/C switch ON/OFF
Other
Condition of MILRemains on Sometimes light up Does not light up
NormalMalfunction code(s) (code )
Freezed frame data ( )
NormalMalfunction code(s) (code )
Freezed frame data ( )
Normal mode
(Precheck)
Check Mode
DTC Inspection Inspector’s
Name
DI−2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI0534
DI5OU−02
P22892DLC3TOYOTA
−Hand− Held Tester
−
DIAGNOSTICS ENGINE
DI−3
1996 LAND CRUISER (RM451U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand −
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on −
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Codes (DTC) prescribed by SAE J2012 are
recorded in the ECM memory (See page DI−13).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTC remain recorded in the ECM memory.
To check the DTC, connect the OBD II scan tool or
TOYOTA hand−held tester to Data Link Connector
3 (DLC3) on the vehicle. The OBD II scan tool or
TOYOTA hand−held tester also enables you to
erase the DTCs and check freezed frame data and
various forms of engine data (For operating instruc-
tions, see the OBD II scan tool’s instruction book.).
DTC include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI−13).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N09214
DI−4
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
The diagnosis system operates in normal mode
during normal vehicle use. It also has a check mode
for technicians to simulate malfunction symptoms
and troubleshoot. Most DTC use 2 trip detection
logic* to prevent erroneous detection, and ensure
thorough malfunction detection. By switching the
ECM to check mode when troubleshooting, the
technician can cause the MIL to light up for a mal-
function that is only detected once or momentarily
(TOYOTA hand−held tester only) (See step 2).
*2 trip detection logic:
When a logic malfunction is first detected, the mal-
function is temporarily stored in the ECM memory.
If the same malfunction is detected again during the
second drive test, this second detection causes the
MIL to light up.
The 2 trip repeats the same mode a 2nd time (How-
ever, the IG switch must be turned OFF between the
1st trip and 2nd trip.).
Freeze frame data:
Freeze frame data records the engine condition
when a misfire (DTC P0300 − P0306) or fuel trim
malfunction (DTC P0171, P0172) or other malfunc-
tion (first malfunction only), is detected.
Because freeze frame data records the engine
conditions (fuel system, calculator load, engine
coolant temperature, fuel trim, engine speed, ve-
hicle speed, etc.) when the malfunction is detected,
when troubleshooting it is useful for determining
whether the vehicle was running or stopped, the en-
gine warmed up or not, the air− fuel ratio lean or rich,
etc. at the time of the malfunction.
Priorities for troubleshooting:
If troubleshooting priorities for multiple DTCs are given in the
applicable diagnostic chart, these should be followed.
If no instructions are given troubleshoot DTCs according to the
following priorities. (1) DTC other than fuel trim malfunction (DTC P0171,
P0172), EGR (DTC P0401, P0402), and misfire
(DTC P0300 − P0306).
(2) Fuel trim malfunction (DTC P0171, P0172), and EGR (DTC P0401, P0402).
(3) Misfire (DTC P0300 − P0306).
(b) Check the DLC3. The vehicle’s ECM uses V.P.W. (V ariable Pulse Width) for
communication to comply with SAE J1850. The terminal
arrangement of DLC3 complies with SAE J1962 and
matches the V.P.W. format.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22215
−
DIAGNOSTICS ENGINE
DI−5
1996 LAND CRUISER (RM451U)
Terminal No.
Connection / Voltage or ResistanceCondition
2Bus 
Line / Pulse generationDuring transmission
4Chassis Ground / ↔ Body Ground 1 Ω or lessAlways
5Signal Ground / ↔ Body Ground 1 Ω or lessAlways
16Battery Positive / ↔ Body Ground 9 − 14 VAlways
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
2. INSPECT DIAGNOSIS (NORMAL MODE)
(a) Check the MIL. (1) The MIL comes on when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine started, the MIL should go off. If the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only: When the diagnosis sys-
tem is switched from normal mode to check mode, it
erases all DTCs and freezed frame data recorded in normal
mode. So before switching modes, always check the DTCs
and freezed frame data, and note them down (1) Prepare the OBD II scan tool (complying with SAE
J 1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand− held tester to DLC3 in the fuse box at the lower left
of the instrument panel.
(3) Turn the ignition switch ON and switch the OBD II
scan tool or TOYOTA hand −held tester switch ON.
(4) Use the OBD II scan tool or TOYOTA hand−held tester to check the DTC and freezed frame data,
note them down. (For operating instructions, see
the OBD II scan tool’s instruction book.)
(5) See page DI−13 to confirm the details of the
DTCs.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI3605
ON
OFF Flashing
0.13 Second
DI−6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTCs are recorded in
the ECM.
3. INSPECT DIAGNOSIS (CHECK MODE)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC. (1) Initial conditions
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in ”park” or ”neutral” position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA hand−held tester ON.
(6) Switch the TOYOTA hand −held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Switch the engine (The MIL goes out after the en- gine start.).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc. (9) After simulating the malfunction conditions, use theTOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00149
DLC1
E1
TE1 SST
P09137
P23430
−
DIAGNOSTICS ENGINE
DI−9
1996 LAND CRUISER (RM451U)
OK
5 Check idle speed.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Switch off all accessories.
(c) Switch off air conditioning.
(d) Shift transmission into ”N” position.
(e) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3 on the vehicle.
CHECK:
Use CURRENT DATA to check the idle speed.
OK:
Idle speed: 650 ± 50 rpm
NG Proceed to matrix chart of problem symptomson page DI−19.
OK
6 Check ignition timing.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Shift transmission into ”N” position.
(c) Keep the engine speed at idle.
(d) Using SST, connect terminals TE1 and E1 of DLC1. SST 09843−18020
(e) Connect a timing light probe to a high −tension cord.
CHECK:
Check ignition timing.
OK:
Ignition timing: 3 ° BTDC at idle
NG Proceed to page IG−1 and continue to trouble-
shoot.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OV−03
−
DIAGNOSTICS ENGINE
DI−13
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to \
the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, che\
ck the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See page ’’ for the respe-
cire ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0100
( DI−20 )Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
 Mass air flow meter
 ECM
 *1
P0101
( DI−25 )Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter *1
P0110
( DI−26 )Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
 Intake air temp. sensor
 ECM
 *1
P0115
( DI−30 )Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
 Engine coolant temp. sensor
 ECM
 *1
P0116
( DI−34 )Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
 Cooling system *1
P0120
( DI−35 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
 Throttle position sensor
 ECM
 *1
P0121
( DI−39 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor *1
P0125
( DI−40 )Insufficient Coolant Temp. for
Closed Loop Fuel Control Open or short in heated oxygen sensor circuit
 Heated oxygen sensor *1
P0130
( DI−43 )Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
 Fuel trim malfunction *1
P0133
( DI−46 ) Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor *1
P0135
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
 *1
P0136
( DI−49 )Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor *1
P0141
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135 *1
*1: MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010