check engine light TOYOTA LAND CRUISER 1996 J80 Owner's Manual

FI7130
Vehicle Speed50 − 65 km/h
(31 − 40 mph)
Idling
IG SW OFF 1 − 3 min.1 min. Time
(1)(2)(3) (4)
(5)
−
DIAGNOSTICS ENGINE
DI−43
1996 LAND CRUISER (RM451U)
DTC P0130 Heated Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40.
DTC No.DTC Detecting ConditionTrouble Area
P0130
Voltage output of heated oxygen sensor (bank 1 sensor 1)
remains at 0.4 V or more, or 0.55 V or less, during idling after
the engine is warmed up (2 trip detection logic)Heated oxygen sensor (bank 1 sensor 1)
 Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The heated oxygen sensor’s output voltage and the shortterm fuel trim value can be read using t\
he OBD
II scan tool or TOYOTA handheld tester.
WIRING DIAGRAM
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−35 for WIRING
DIAGRAM.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand−held tester to the DLC3.
(2) Switch the TOYOTA hand−held tester from normal mode to check mode (See page DI−3).
(3) Start the engine and warm it up withe all accessory switches OFF.
(4) Drive the vehicle at 50 − 65 km/h (31 − 40 mph) for 1 − 3 min. to warm up the heated oxygen sensor.
(5) Let the engine idle for 1 min.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the\
malfunction will not be possible.
If you do not have a TOYOTA hand −held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI5PA−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−51
1996 LAND CRUISER (RM451U)
DTC P0171 System too Lean (Fuel Trim)
DTC P0172 System too Rich (Fuel Trim)
CIRCUIT DESCRIPTION
”Fuel trim” refers to the feedback compensation value compared against the basic injection time. Fuel trim
includes short−term fuel trim and long −term fuel trim.
”Short−term fuel trim” is the short−term fuel compensation used to maintain the air −fuel ratio at its ideal
theoretical value. The signal from the heated oxygen sensor indicates whether the a\
ir −fuel ratio is RICH or
LEAN compared to the ideal theoretical value, triggering a reduction in fuel \
volume if the air −fuel ratio is rich,
and an increase in fuel volume if it is lean.
”Long −term fuel trim” is overall fuel compensation carried out long −term to compensate for continual devi-
ation of the short−term fuel trim form the central value due to individual engine differences, wear over time
and changes in the usage environment.
If both the short−term fuel trim and long−term fuel trim are LEAN or RICH beyond a certain value, it is de-
tected as a malfunction and the MIL lights up.
DTC No.DTC Detecting ConditionTrouble Area
P0171
When the air fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the RICH side.
(2 trip detection logic)
 Air intake (hose loose)
 Fuel line pressure
 Injector blockage, leak
 Heated oxygen sensor (bank 1 sensor 1) malfunction
 Mass air flow meter
 Engine coolant temp. sensor
P0172
When the air fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the LEAN side.
(2 trip detection logic)
Fuel line pressure
 Injector blockage, leak
 Heated oxygen sensor (bank 1 sensor 1) malfunction
 Mass air flow meter
 Engine coolant temp. sensor
HINT:
When the DTC P0171 is recorded, the actual air− fuel ratio is on the LEAN side. When DTC P0172 is
recorded, the actual air−fuel ratio is on the RICH side.
If the total of the short −term fuel trim value and long −term fuel trim value is within + 30 − − 35 %, the
system is functioning normally.
If the vehicle runs out of fuel, the air −fuel ratio is LEAN and DTC P0171 is recorded. The MIL then come
on.
INSPECTION PROCEDURE
1 Check air induction system (See page SF−1 ).
NG Repair or replace
OK
DI5PE−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P20769
(43 − 56 mph)
Vehicle Speed
70 − 90 km/h
Idling
IG SW OFF (1)(2) (3)
(4) (6)
(5)
Warm up 3 − 5 min. 2 min.
3 − 5 min.2 min.(7)
Time
DI−70
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
SYSTEM CHECK DRIVING PATTERN
(1) Connect the OBD II scan tool or TOYOTA hand −held tester to the DLC3.
(2) Start and warm up the engine with all accessories switched OFF.
(3) Run the vehicle at 70 − 90 km/h (43 − 56 mph) for 3 min. or more.
(4) Idle the engine for about 2 min.
(5) Stop at safe place and turn the ignition switch OFF.
(6) Start the engine and do steps (3) and (4) again.
(7) Check the ”READINESS TESTS” mode on the OBD II scan tool or\
TOYOTA hand−held tester.
If ”COMPL” is displayed and the MIL does not light up, the system \
is normal.
If ”INCMPL” is displayed and the MIL does not light up, run the ve\
hicle again and check it.
HINT:
”INCMPL” is displayed when either condition (a) or (b) exists.\
(a) The system check is incomplete.
(b) There is a malfunction in the system.
If there is a malfunction in the system, the MIL will light up after ste\
ps (2) to (6) above are done.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08225
Q08634
TOYOTA Hand−held Tester
DLC3
DI−132
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
The diagnosis system operates in normal mode
during normal vehicle use, and also has a check
mode for technicians to simulate malfunction symp-
toms and perform troubleshooting. Most DTCs use
2 trip detection logic(*) to prevent erroneous detec-
tion. By switching the ECM to check mode when
troubleshooting, the technician can cause the MIL
to light up for a malfunction that is only detected
once or momentarily (TOYOTA hand−held tester)
(See step 3).
*2 trip detection logic:
When a logic malfunction is first detected, the mal-
function is temporarily stored in the ECM memory.
If the same malfunction is detected again during the 2nd test
drive, this 2nd detection causes the MIL to light up.
2. Normal Mode: INSPECT DIAGNOSIS
(a) Check the MIL. (1) The MIL lights up when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine is started, the MIL should go off.
If the lamp remains on, the diagnosis system has
detected a malfunction or abnormality in the sys-
tem.
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only:
When the diagnostic system is switched from the normal
mode to the check mode, it erases all DTCs and freeze
frame data recorded in the normal mode. So before switch-
ing modes, always check the DTCs and freeze frame data,
and note them down. (1) Prepare the OBD II scan tool (complying with SAEJ1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand−
held tester to the DLC3 in the fuse box at the lower
left of the instrument panel.
(3) Turn the ignition switch ON and turn the OBD II scan
tool or TOYOTA hand−held tester switch ON.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08634
TOYOTA Hand−held Tester
DLC3
FI3605
ON
OFF 0.13 sec.
Flashing
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−133
1996 LAND CRUISER (RM451U)
(4) Use the OBD II scan tool or TOYOTA hand−held
tester to check the DTCs and freeze frame data.
Note them down (For operating instructions, see
the OBD II scan tool’s instruction book).
(5) See page DI−143 to confirm the details of the
DTCs.
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTCs, use
the normal mode. For codes on the DTC chart subject to ”2
trip detection logic”, turn the ignition switch off after the
symptoms have been simulated for the 1st time. Them re-
peat the simulation process again. When the program has
been simulated twice, the MIL lights up and the DTCs are
recorded in the ECM.
3. Check Mode: INSPECT DIAGNOSIS
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has high sens-
ing ability to detect malfunctions. Furthermore, the same diag-
nostic items which are detected in the normal mode can also be
detected in check mode.
(a) Check the DTC. (1) Check the initial conditions.
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in P position.
Air conditioning switched off.
(2) Turn the ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand− held tester to the
DLC3 in the fuse box at the lower left of the instru-
ment panel.
(5) Turn the ignition switch ON and switch the T OYOTA
hand −held tester ON.
(6) Switch the TOYOTA hand −held tester from the nor-
mal mode to the check mode (Check that the MIL
flashes).
(7) Start the engine (The MIL goes).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTCs etc.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−136
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
If the lock−up is defective:
Lock−up solenoid is stuck.
Lock−up control valve is stuck.
Lock−up signal value is stuck.
(2) In the same way, check the shock and slip at the 1 → 2, 2 →3 and 3 → O/D up−shift.
Evaluation:
If the shock is excessive:
Line pressure is too high.
Accumulator is defective.
Check ball is defective. (3) Run at the D position lock −up or O/D gear and check for abnormal noise and vibration.
HINT:
The check for the cause of abnormal noises and vibration must be made with \
extreme care as it could also
be due to loss of balance in the propeller shaft, differential, torque converter clutch, etc.
(4) While running in the D position, 2nd, 3rd and O/D gears, check to see that the\
possible kick −down
vehicle speed limits for 2 →1, 3 → 2 and O/D →3 kick−downs conform to those indicated on
the automatic shift schedule.
(5) Check for abnormal shock and slip at kick −down.
(6) Check for the lock −up mechanism.
Drive in D position, O/D gear, at a steady speed (lock −up ON) of about 95 km/h (59 mph).
Lightly depress the accelerator pedal and check that the engine RPM does not change
abruptly.
If there is a big jump in engine RPM, there is no lock −up.
(b) 2 position test. Shift into the 2 position and, while driving with the accelerator pedal held \
constantly at the full throttle
valve opening position, push in one of the pattern selectors and check the fo\
llowing points:
HINT:
When the 2nd start switch is on, there is no 1 → 2 up−shift and 2 →1 down−shift.
(1) Check to see that the 1 → 2 up− shift takes place and that the shift point conforms to the automatic
shift schedule.
HINT:
There is no O/D up−shift and lock−up in the 2 position. (2) While running in the 2 position and 2nd ge ar, release the accelerator pedal and check the engine
braking effect.
Evaluation:
If there is no engine braking effect:
2nd coast brake is defective. (3) Check for abnormal noise at acceleration and deceleration, and for shock at up −shift and down −
shift.
(c) L position test. (1) While running in the L position, check to see that there is no up −shift to 2nd gear.
(2) While running in the L position, release the accelerator pedal and check the engine braking ef- fect.
Evaluation:
If there is no engine braking effect:
1stand reverse brake is defective. (3) Check for abnormal noise during acceleration and deceleration.
(d) R position test. Shift into the R position and fully depress the accelerator pedal and ch\
eck for slipping.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07310Control Shaft Lever(b)
(c)
Q07311
Neutral Basic Line
Bolt
Groove
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−139
1996 LAND CRUISER (RM451U)
(3) Return the control shaft lever 2 notches to N posi-
tion.
(4) Set the shift lever to N position.
(5) While holding the shift lever lightly toward the R
position side, adjust the control rod nut.
(6) Tighten the control rod nut.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(7) Start the engine and make sure that the vehicle moves forward when shifting the lever from the N to
D position and reverses when shifting it to the R
position.
(g) Inspec and adjust park/neutral positoin switch. Check that the engine can be started with the shift lever
only in the N or P position, but not in other positions.
If not as stated above, carry out the following adjustment proce-
dure.
(1) Loosen the park/neutral position switch bolt and set
the shift lever to the N position.
(2) Align the groove and neutral basic line.
(3) Hold in position and tighten the bolt.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf) For continuity inspect of the park/neutral position
switch, see page DI−169 .
(h) Check the idle speed. Idle speed:
650 ± 50 rpm (In N position and air conditioner OFF)
7. MECHANICAL SYSTEM TESTS
(a) Measure the stall speed. The object of this test is to check the overall performance of the transmis\
sion and engine by measuring
the stall speeds in the D and R positions.
NOTICE:
Do the that at normal operating ATF temperature 50 − 80°C (122 − 176° F).
Do not continuously run this test longer than 5 seconds.
To ensure safety, conduct this test in a wide, clear, level area which provides good traction.
The stall test should always be carried out in pairs. One technician should\
observe the condi-
tions of wheels or wheel stoppers outside the vehicle while the other is doin\
g the test.
(1) Chock the 4 wheels.
(2) Connect an OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(3) Fully apply the parking brake.
(4) Keep your left foot pressed firmly on the brake pedal.
(5) Start the engine.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KH−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−147
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check but\
the trouble still occurs, check the
circuits for each symptom in the order given in the charts on the following pages and\
proceed to the page
given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On−Vehicle repair Matrix Chart
Chapter 3: Off−Vehicle repair Matrix Chart
When troubleshooting, check Chapter 1 first. If instructions are given i\
n Chapter 1 to proceed to chapter 2
or 3, proceed as instructed.
(1) If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow
chart for each circuit, proceed to the circuit with the next highest number in the table to cont\
inue
the check.
(2) If the trouble still occurs even though there are no abnormalities in any\
of the other circuits, then check and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion6. On−vehicle repair matrix chart
7. Off −vehicle repair matrix chart−
−
Vehicle does not move in a particular position or positions1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No up− shift (1st → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up −shift (2nd → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up− shift (3rd → O/D)
1. O/D main switck& O/D OFF indicator light circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Throttle position sensor circuit
6. Park/neutral position switch circuit
7. O/D cancel signal circuit
8. Engine coolant temp. sensor circuit
9. On−vehicle repair matrix chart
10.Off −vehicle repair matrix chart
11. ECMDI−174
DI−157 DI−87
DI−166 DI−35
DI−169
DI−172 DI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N09348
Interface BoxHarness VehicleTOYOTA
Tester
Hand
−held
TOYOTA Break −out− box
F00007
DLC1
Ts Tc
E
1
BR3904
0.25 sec. 0.25 sec.
ON
OFF
DI−192
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(d) Using TOYOTA break −out− box and TOYOTA hand− held
tester, measure the ECU terminal values.
(1) Hook up the T OYOTA hand−held tester and TOYO-
TA break−out−box to the vehicle.
(2) Read the ECU input/output values by following the prompts on the tester screen.
HINT:
TOYOTA hand −held tester has a ”Snapshot ” function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand−held tester/TOYOTA break
out−box operators manual for further details.
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR CHECK
(a) Check the speed sensor signal. (1) Conform that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(7) Stop the vehicle.
(8) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(9) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC on page DI−190 .
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time, the low-
est numbered code will be displayed 1st.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR3893
Malfunction Code (Example Code 72, 76)
72 6
7
ON
OFF
0.5 sec.
0.5 sec.
0.5 sec.
0.5 sec. 1.5 sec.
2.5 sec. 4 sec.
Repeat
F00007
E1
Ts
DLC1
R05599
0.13 sec.
0.13 sec.
3 sec.
ON
OFF
R05037
860 
30 mm
33.86  1.18 in.
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−193
1996 LAND CRUISER (RM451U)
(10) After doing the check, disconnect terminals Ts and
E
1, Tc and E1 of the DLC1, and turn the ignition
switch OFF.
(b) Deceleration sensor detection point check. (1) Confirm that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Jack up the rear side of the vehicle slowly.
HINT:
When measuring the height, measure at the center of the lower
body of the vehicle. (7) Check that the warning light blinks.
If the warning light turns on, inspect the deceleration sensor
installation. If the sensor installation is OK, replace the decel-
eration sensor. (8) Jack down the vehicle slowly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010