ignition TOYOTA LAND CRUISER 1996 J80 Workshop Manual

FI4848
FI4849
SF−30
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
(f) Install the grommet and O−ring to the injector.
(g) Connect SST (union and hose) to the injector, and hold
the injector and union with SST (clamp).
SST 09268−41046
(h) Put the injector into the graduated cylinder.
HINT:
Install a suitable vinyl hose onto the injector to prevent gasoline
from splashing out.
(i) Remove the fuse cover on the instrument panel.
(j) Connect the TOYOTA hand−held tester to the DLC3.
(k) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
NOTICE:
Do not start the engine.
(l) Select the active test mode on the TOYOTA hand −held
tester.
(m) Please refer to the TOYOTA hand −held tester operator’s
manual for further details.
(n) If you have no TOYOTA hand−held tester, connect the positive (+) and negative (−) leads from the battery to the
fuel pump connector (See page SF−14)
(o) Connect SST (wire) to the injector and battery for 15 se- conds, and measure the injection volume with a gra-
duated cylinder. Test each injector 2 or 3 times.
SST 09842−30070
Volume:
69 − 88 cm
3 (4.2 − 5.4 cu in.) per 15 seconds
Difference between each injector:
5 cm
3 (0.3 cu in.) or less
If the injection volume is not as specified, replace the injector.
2. INSPECT LEAKAGE
(a) In the condition above, disconnect the test probes of SST (wire) from the battery and check the fuel leakage from
the injector.
SST 09842−30070
Fuel drop: One drop or less per minute
(b) Turn the ignition switch to LOCK.
(c) Disconnect the negative ( −) terminal cable from the bat-
tery.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16A−03
−
STEERING TILT STEERING COLUMN
SR−11
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE STEERING WHEEL PAD
NOTICE:
If the airbag connector is disconnected with the ignition
switch at ON or ACC, DTCs will be recorded. Never use air-
bag parts from another vehicle. When replacing parts, re-
place with new parts.
(a) Place the front wheels facing straight ahead.
(b) Remove the steering wheel lower No.2 and No.3 cover from the steering wheel.
(c) Using a torx socket wrench, loosen the 2 torx screws.
HINT:
Loosen the 2 screws until the groove along the screw circumfer-
ence catches on the screw case.
(d) Pull out the wheel pad from the steering wheel and dis- connect the airbag connector.
CAUTION:
When storing the wheel pad, keep the upper surface of the
pad facing upward. Never disassemble the wheel pad.
NOTICE:
When removing the wheel pad, take care not to pull the air-
bag wire harness.
2. REMOVE STEERING WHEEL
(a) Disconnect the connector.
(b) Remove the steering wheel set nut.
(c) Place matchmarks on the steering wheel and main shaft assembly.
(d) Using SST, remove the wheel. SST 09950 −50010 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16C−01
−
STEERING TILT STEERING COLUMN
SR−15
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT STEERING LOCK OPERATION
Check that the steering lock mechanism operates properly.
2. IF NECESSARY, REPLACE KEY CYLINDER
(a) Place the ignition key at the ACC position.
(b) Push down the stop pin with a screwdriver, and pull out
the cylinder.
(c) Install a new cylinder.
HINT:
Make sure the key is at the ACC position.
3. INSPECT IGNITION SWITCH (See page BE−11)
4. INSPECT KEY UNLOCK WARNING SWITCH (See page BE−11 )
5. IF NECESSARY, REPLACE IGNITION SWITCH WITH KEY UNLOCK WARNING SWITCH
(a) Remove the 2 screws.
(b) Install a new switches with the 2 screws.
6. INSPECT KEY INTERLOCK SOLENOID (See page SR−9 )
7. IF NECESSARY, REPLACE KEY INTERLOCK SOLE- NOID
(a) Remove the 2 screws.
(b) Remove the solenoid, spring and lock pin.
(c) Install a new solenoid with the spring and lock pin, with the
2 screws.
8. IF NECESSARY, REPLACE BUSHING
(a) Using a screwdriver, remove the bushing from the column lower tube.
(b) Coat a new bushing with molybdenum disulfide lithium base grease.
(c) Align the holes of the tube and projections of the bushing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EO−04
SS−4
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
127
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE MECHANICAL
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,176 kPa (12.0 kgf/cm2, 171 psi) or more
883 kPa (9.0 kgf/cm2, 128 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve clearanceat cold Intake Exhaust0.15 − 0.25 mm (0.006 − 0.010 in.)
0.25 − 0.35 mm (0.010 − 0.014 in.)
Ignition timingw/ Terminals TE1 and E1 connected3° BTDC @ idle
Idle speed−650 ± 50 rpm
Cylinder headWarpage
Cylinder block side Maximum
Manifold side Maximum
Valve seat
Refacing angle Intake
Exhaust
Contacting angle
Contacting width Intake
Exhaust
Cylinder head bolt outside diameter STD
Minimum
0.15 mm (0.0059 in.)
0.10 mm (0.0039 in.)
30°, 45° , 75°
45 °, 75°
45 °
1.2 − 1.6 mm (0.047 − 0.063 in.)
1.0 − 1.4 mm (0.039 − 0.055 in.)
10.85 − 11.00 mm (0.4272 − 0.4331 in.)
10.6 mm (0.417 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD O/S 0.05
Protrusion height7.010 − 7.030 mm (0.2760 − 0.2768 in.)
11.492 − 11.513 mm (0.4524 − 0.4533 in.)
11.542 − 11.563 mm (0.4544 − 0.4522 in.)
8.2 − 8.6 mm (0.323 − 0.339 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake Exhaust
Valve face angle
Stem diameter Intake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum98.4 mm (3.874 in.)
97.9 mm (3.854 in.)
97.9 mm (3.854 in.)
97.4 mm (3.835 in.)
44.5 °
6.970 − 6.985 mm (0.2744 − 0.2750 in.)
6.965 − 6.980 mm (0.2742 − 0.2748 in.)
0.025 − 0.060 mm (0.0010 − 0.0024 in.)
0.030 − 0.065 mm (0.0012 − 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.2 mm (0.047 in.)
1.0 mm (0.039 in.)
Valve springDeviation Maximum
Free length
Installed tension at 36.5 mm (1.437 in.)2.0 mm (0.079 in.)
43.94 − 45.06 mm (1.7299 − 1.7740 in.)
214 − 238 N (21.8 − 24.2 kgf, 48.1 − 53.4 lbf)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum33.966 − 33.976 mm (1.3372 − 1.3376 in.)
34.000 − 34.021 mm (1.3386 − 1.3394 in.)
0.024 − 0.055 mm (0.0009 − 0.0022 in.)
0.07 mm (0.0028 in.)
ManifoldWarpage Maximum0.30 mm (0.0118 in.)
Air intake chamberWarpageMaximum0.30 mm (0.0118 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EY−03
−
SERVICE SPECIFICATIONS IGNITION
SS−17
140
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION
SERVICE DATA
Firing order−1 − 5 − 3 − 6 − 2 − 4
High −tension cordResistance Maximum25 kΩ per cord
Spark plugRecommended spark plug ND
NGK
Correct electrode gapK16R−U
BKR5EYA
0.8 mm (0.031 in.)
Ignition coilPrimary coil resistance at cold
at hot
Secondary coil resistance at cold
at hot0.36 − 0.55 Ω
0.45 − 0.65 Ω
9.0 − 15.4 kΩ
11.4 − 18.1 kΩ
DistributorAir gap
Pickup coil resistance at cold (G1 − G)
(G2 − G)
(NE − G)
at hot (G1 − G )
(G2 − G)
(NE − G)0.2 − 0.4 mm (0.008 − 0.016 in.)
185 − 275 Ω
185 − 275 Ω
185 − 275 Ω
240 − 325 Ω
240 − 325 Ω
240 − 325 Ω
Crankshaft
position sensorResistance at cold (NE − NE )
at hot (NE − NE )1,630 − 2,740 Ω
2,065 − 3,225 Ω
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EZ−01
SS−18
−
SERVICE SPECIFICATIONS IGNITION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Spark plug x Cylinder head2020014
Distributor x Cylinder head1818013
Crankshaft position sensor protector x No. 1 oil pan2020014
Crankshaft position sensor x No. 1 oil pan99078 in.·lbf
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010