roof TOYOTA LAND CRUISER 1996 J80 Owner's Manual

BO5152
BO391−01
BO−68
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SLIDING ROOF GLASS ALIGNMENT
(a) Start the engine and check the operation time of the slid-
ing roof.
Operation time: Approx. 5 sec.
(b) Check for abnormal noise or binding during operation.
(c) With the sliding roof fully closed, check for water leakage.
(d) Check for a difference in level between the sliding roof weatherstrip and roof panel.
Front End0.9 − 3.9 mm (0.035 − 0.154 in.)
Rear End0.9 − 3.9 mm (0.035 − 0.154 in.)
2. If the sliding roof does not operate:
ADJUST SLIDING ROOF GLASS ALIGNMENT
(a) Remove the control switch cover.
(b) Remove the large screw inside.
NOTICE:
Be careful not to lose the spring washer or shim.
(c) Manually operate the moon roof by inserting a special
crank−shaped screwdriver into the hole and turning the
drive shaft.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO4033
BO392−01
−
BODY SLIDING ROOF
BO−69
1996 LAND CRUISER (RM451U)
ADJUSTMENT
1. REMOVE SLIDING ROOF GARNISHES
Before making adjustments, remove the left and right sliding
roof garnishes.
HINT:
After adjustment, reinstall the sliding roof garnishes.
2. ADJUST LEVEL DIFFERENCE
Adjust by increasing or decreasing the number of shims be-
tween the bracket and sliding roof.
3. ADJUST FORWARD OR REARWARD
(a) Adjust by loosening the sliding roof installation nuts, and
move the sliding roof bracket forwards and backwards.
(b) When the front or rear alignment is not correct, remove the glass and adjust the drive rail.
(c) Using a screwdriver, slide the link forwards or backwards to align the 2 marks, as shown in the illustration.
(d) Slide the bracket to the forefront with your hand.
4. ADJUST RIGHT OR LEFT
Adjust by loosening the sliding roof rear shoe installation nuts,
and move the sliding roof to the right and left.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−70
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
5. ADJUST LEFT/RIGHT CLEARANCE
Adjust by loosening the sliding roof installation nuts and read-
just the sliding roof to the proper position.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO395−01
−
BODY SLIDING ROOF
BO−71
1996 LAND CRUISER (RM451U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BO−67 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO396−01
BO−72
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See pageBO−63 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03244Press Down
Lock
P03245Lock Insert
FI2553
SST
SF−2
−
SFI SFI SYSTEM
630
Author: Date:
1996 LAND CRUISER (RM451U)
HINT:
Always check the diagnostic trouble code before disconnecting
the negative ( −) terminal cable from the battery.
(b) When installing the battery, be especially careful not to in-
correctly connect the positive (+) and negative ( −) cables.
(c) Do not permit parts to receive a severe impact during re- moval or installation. Handle all SFI parts carefully, espe-
cially the ECM.
(d) Do not be careless during troubleshooting as there are numerous transistor circuits and even slight terminal con-
tact can further troubles.
(e) Do not open the ECM cover.
(f) When inspecting during rainy weather, take care to pre-
vent entry of water. Also, when washing the engine
compartment, prevent water from getting on the SFI parts
and wiring connectors.
(g) Parts should be replaced as an assembly.
(h) Care is required when pulling out and inserting wiring con-
nectors.
(1) Release the lock and pull out the connector, pulling
on the connectors.
(2) Fully insert the connector and check that it is locked.
(i) When inspecting a connector with a volt/ohmmeter (1) Carefully take out the water −proofing rubber if it is
a water−proof type connector.
(2) Insert the test probe into the connector from the wir-
ing side when checking the continuity, amperage or
voltage.
(3) Do not apply unnecessary force to the terminal.
(4) After checking, install the water−proofing rubber on
the connector securely.
(j) Use SST for inspection or test of the injector or its wiring connector.
SST 09842−30070
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010