transmission TOYOTA LAND CRUISER 1996 J80 Owner's Manual

Q07314
P1P2
P
AT
−14
−
AUTOMATIC TRANSMISSION SHIFT LOCK SYSTEM
1996 LAND CRUISER (RM451U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals 7 and 8.
Standard resistance: 12 − 17 Ω
If the resistance is not as specified, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that there is continuity between each terminal.
Shift positionTester condition to
terminal numberSpecified value
P position (Release
button is not pushed)P1 − PContinuity
P position (Release
button is pushed)P1 − P
P2 − PContinuity
R, N, D, 2, L positionP2 − PContinuity
If the continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0T8−01
Q07275
Radiator GrilleOil Cooler
−
AUTOMATIC TRANSMISSION AIR COOLED OIL COOLER
AT−15
799
Author: Date:
1996 LAND CRUISER (RM451U)
AIR COOLED OIL COOLER
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0T9−01
AT−16
−
AUTOMATIC TRANSMISSION AIR COOLED OIL COOLER
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE RADIATOR GRILLE
(a) Remove the 5 screws.
(b) Using a screwdriver, disconnect the clip.
HINT:
Tape a screwdriver tip before use.
(c) Remove the radiator grille.
2. REMOVE OIL COOLER
(a) Loosen the 2 clips and disconnect the 2 hoses.
(b) Remove the 8 bolts and oil cooler. Torque: 11 N·m (115 kgf·cm, 8 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0TA−01
−
AUTOMATIC TRANSMISSION AIR COOLED OIL COOLER
AT−17
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page AT −16).
HINT:
After installation, check fluid level (See page DI−131).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0TB−01
Q08463
Hold Down ClampBattery
Battery Tray
Starter
Fan Shroud
Level Gauge Front Propeller Shaft
Oil Filler Pipe
 Gasket
 Hole Plug
O− Ring
Engine Under Cover Stabilizer BarCrossmember with
Transfer Under Cover
 Non− reusable Part 
 Gasket

AT
−18
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
802
Author: Date:
1996 LAND CRUISER (RM451U)
AUTOMATIC TRANSMISSION UNIT
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08467
Rear Propeller
ShaftTransfer Shift
Lever Boot
Transmission Shif
Lever Assembly
Rear Console Box
Front Console Box
Engine Rear Mounting
Plug for Hydraulic Test
Oil Cooler Pipe Transfer Shift
Control Link
Transfer Shift
Lever Cushion
x 6
x 6 Clip
Transfer Shift
Lever Knob
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−19
803
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0TC−01
AT−20
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE BATTERY AND BATTERY TRAY
2. REMOVE 2 BOLTS AND LOOSEN FAN SHROUD OF COOLING FAN TO AVOID DAMAGE TO FAN
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
3. DISCONNECT THROTTLE CABLE
(a) Loosen the adjusting nut and disconnect the cable from the bracket.
(b) Disconnect the throttle cable from the linkage.
4. REMOVE UPPER SIDE STARTER MOUNTING BOLT Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
5. REMOVE TRANSMISSION SELECT L EVER AND
TRANSFER SHIFT LEVER
(a) Remove the clip, washer and wave washer, and discon- nect the transfer shift lever link.
(b) Remove the nut and washer, and disconnect the trans- mission select lever link.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−21
1996 LAND CRUISER (RM451U)
(c) Remove the transfer shift lever knob.
(d) Remove the 4 screws and console.
(e) Remove the 4 screws and transfer shift lever boot.
(f) Remove the 3 bolts and console box.
(g) Disconnect the 3 connectors.
(h) Remove the 6 screws and transmission shift lever assem-
bly.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT−22
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(i) Remove the 4 bolts and transfer shift lever.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(j) Remove the 2 cushions.
6. DISCONNECT THESE CONNECTORS:
No.1 vehicle speed sensor
No.2 vehicle speed sensor
Park/neutral position switch
Solenoid connector
ATF temperature sensor
Center differential lock indicator switch
L4 position switch
Neutral position switch
7. DISCONNECT BLEEDER HOSE FROM TRANSFER
8. REMOVE FRONT AND REAR PROPELLER SHAFT (See page PR−3 )
9. REMOVE OIL FILLER PIPE
(a) Remove the level gauge.
(b) Remove the upper side mounting bolt.
(c) Remove the bolt and filler pipe.
HINT:
At the time of installation, replace the used O −ring with a new
one.
10. LOOSEN 2 OIL COOLER PIPE UNION NUTS
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−23
1996 LAND CRUISER (RM451U)
11. REMOVE 4 STABILIZER BAR BRACKET MOUNTING
BOLTS
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
12. REMOVE ENGINE UNDER COVER
Remove the 4 bolts and engine under cover. Torque: 28 N·m (290 kgf·cm, 21 ft·lbf)
13. REMOVE TORQUE CONVERTER CLUTCH MOUNT- ING BOLT
(a) Remove the converter hole plug.
(b) Turn the crankshaft to gain access to each bolt.
(c) Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.
Torque: 55 N·m (550 kgf·cm, 40 ft·lbf)
HINT:
At the time of installation, first install gray colored bolt and then
5 other bolts.
14. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(a) Remove the 2 nuts, bolts and gasket, and disconnect the
front exhaust pipe assembly.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
HINT:
At the time of inatallation, replace the used nuts and gasket with
new nuts and gasket.
(b) Loosen the clamp bolt and disconnect the clamp from the
No.1 support bracket.
Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
(c) Remove the 2 bolts and No.1 support bracket. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010