Oil transmission TOYOTA LAND CRUISER 1996 J80 Owner's Guide

MA02R−04
MA−4
−
MAINTENANCE UNDER HOOD
44
Author: Date:
1996 LAND CRUISER (RM451U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTICE
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performe\
d.
Periodic maintenance service must be performed according to whichever interval in\
the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time inter\
val (months).
Maintenance service after the last period should be performed at the same interval \
as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and incre\
ase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL Check that the coolant level is between the FULL and LOW lines on the se\
e −through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leave\
s, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upp\
er and lower level lines on the case.
If level is low, add distilled water only.
6. BRAKE FLUID LEVELS
Check that the brake fluid level is near the upper level line on the see\
−through reservoir.
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temp\
erature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking and foot brake applied, shift the sel\
ector into all positions from the P to L, and then shift into the P.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re −insert the dipstick fully and check that
the fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 − 80°C (158 − 176° F)).
HINT:
Wait about 30 minutes before checking the fluid level after extended driving\
at high speeds in hot weather,
driving in heavy traffic or with a trailer.
11. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose supports.
If any change in the sound of the exhaust or smell of the exhaust fumes is\
noticed, have the cause located
and corrected.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA04V−01
P22573
−
MAINTENANCE CHASSIS
MA−7
47
Author: Date:
1996 LAND CRUISER (RM451U)
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering linkage for looseness or damage.
Check that the tie rod ends do not have excessive
play.
Check that the boot clamps are not loose.
(b) Inspect the dust cover for damage.
2. INSPECT SRS AIRBAG (Driver airbag: See page RS−9 )
(Front passenger airbag: See page RS−23 )
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
If leakage is found, check for cause and repair.
4. INSPECT OIL LEVEL IN AUTOMATIC TRANSMISSION
(See page DI−131 )
5. INSPECT OIL LEVEL IN TRANSFER AND DIFFEREN- TIAL
(a) Transfer: Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole.
If the level is low, add oil until it begins to run out of the filler hole.
Oil drade: API GL −4 or GL−5
Viscosity: 75W−90
(b) Differential: Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole.
If the level is low, add oil until it begins to run out of the filler hole.
Oil drade: Hypoid gear oil API GL −5
Viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
6. REPLACE AUTOMATIC TRANSMISSION FLUID (See page DI−3)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP300−01
PP−2
−
PREPARATION ENGINE MECHANICAL
51
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE MECHANICAL
SST (Special Service Tools)
09201−10000Valve Guide Bushing Remover &
Replacer Set
(09201−01070)Valve Guide Bushing Remover &
Replacer 7
09202−70020Valve Spring Compressor
(09202−00010)Attachment
09213−58012Crankshaft Pulley Holding Tool
09223−15030Oil Seal & Bearing ReplacerCrankshaft rear oil seal
09236−00101Water Pump Overhaul Tool Set
(09236−15010)Bearing StayValve stem oil seal
09248−06020Valve Lifter Stopper
09248−55050Valve Clearance Adjust Tool Set
(09248−05510)Valve Lifter Press
09316−60011Transmission & Transfer Bearing
Replacer
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KT−01
−
PREPARATION AUTOMATIC TRANSMISSION
PP−29
78
Author: Date:
1996 LAND CRUISER (RM451U)
AUTOMATIC TRANSMISSION
SST (Special Service Tools)
09032−00100Oil Pan Seal Cutter
09201−10000Valve Guide Bushing Remover &
Replacer SetSpeedometer driven gear oil seal
(09201−01080)Valve Guide Bushing Remover &
Replacer 8
09350−30020TOYOTA Automatic Transmission
Tool Set
(09351−32010)One−way Clutch Test Tool
(09351−32020)Stator Stopper
09921−00010Spring Tension ToolSpeedometer driven gear oil seal
09992−00095Automatic Transmission Oil
Pressure Gauge Set
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KR−01
−
PREPARATION AUTOMATIC TRANSMISSION
PP−33
1996 LAND CRUISER (RM451U)
SSM (Special Service Materials)
08826−00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)Oil pan
08833−00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentExtension housing
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KQ−01
PP−34
−
PREPARATION TRANSFER
83
Author: Date:
1996 LAND CRUISER (RM451U)
TRANSFER
SST (Special Service Tools)
09223−00010Cover & Seal ReplacerCenter differential
09223−15020Oil Seal & Bearing ReplacerFront extension housing
09316−12010Transfer Bearing ReplacerCenter differential
09316−20011Transfer Bearing ReplacerFront extension housing
Rear extension housing
Component parts removal and instal-
lation
09316−60011Transmission & Transfer Bearing
Replacer
(09316−00011)Replacer PipeFront extension housing
Rear extension housing
Idler gear
Component parts removal and instal-
lation
Center differential
(09316−00021)Replacer ”A”Rear extension housing
(09316−00031)Replacer ”B”Front extension housing
Rear extension housing
Idler gear
Component parts removal and instal-
lation
Input shaft
(09316−00041)Replacer ”C”Component parts removal and instal-
lation
Front extension housing
Rear extension housing
(09316−00061)Replacer ”E”Front extension housing
(09316−00071)Replacer ”F”Idler gear
Front extension housing
09325−12010Transmission Oil PlugRear extension housing
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KP−01
PP−42
−
PREPARATION SUSPENSION AND AXLE
91
Author: Date:
1996 LAND CRUISER (RM451U)
SUSPENSION AND AXLE
SST (Special Service Tools)
09214−76011Crankshaft Pulley ReplacerFront differential
Rear differential
09223−15020Oil Seal & Bearing ReplacerFront differential
Rear axle
09226−10010Crankshaft Front & Rear Bearing
ReplacerRear suspension
09308−00010Oil Seal PullerFront axle
Front differential
Rear axle
Rear differential
09308−10010Oil Seal PullerFront differential
Rear differential
09315−00022Clutch Release Bearing Remover
& ReplacerRear differential
09316−20011Transfer Bearing ReplacerRear suspension
09316−60011Transmission & Transfer Bearing
ReplacerFront differential
Rear differential
(09316−00011)Replacer Pipe
(09316−00021)Replacer ”A”
(09316−00051)Replacer ”D”
09330−00021Companion Flange Holding ToolFront differential
Rear differential
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EP−01
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−7
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Distributor x Cylinder head1818013
No. 1 engine hanger x Cylinder head4142030
No. 2 engine hanger x Cylinder head4142030
Air intake chamber x Intake manifold2121015
Intake manifold x Cylinder head2121015
Heater inlet pipe x Intake manifold2121015
EGR pipe x Cylinder head2121015
EGR pipe x EGR valve Union nut7880058
Water outlet x Cylinder head2121015
Generator bracket x Cylinder head4344032
Cylinder head x Cylinder block 1st
2nd 3rd39
Turn 90°
Turn 90°400
Turn 90°
Turn 90°29
Turn 90°
Turn 90°
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head1616012
Camshaft timing gear x Camshaft7475054
Chain tensioner x Cylinder head2121015
Water bypass outlet x Cylinder head2121015
Heater pipe x Timing chain cover2121015
Heater pipe x Cylinder head2020014
Exhaust manifold x Cylinder head3940029
Heat insulator x Exhaust manifold1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission2424017
No. 1 support bracket clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
No. 2 water bypass pipe x Cylinder head2020014
No. 2 water bypass pipe x No. 1 engine hanger2020014
Fuel inlet hose x Fuel filter2930022
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
Oil dipstick guide x Intake manifold2020014
Oil dipstick guide x No. 1 oil pan2020014
PS reservoir tank x Air intake chamber2020014
Oil jet x Cylinder block2020014
Vibration damper x Cylinder block2020014
Chain tensioner slipper x Cylinder block6970051
Timing chain cover x Cylinder block2121015
Drive belt idler pulley x Timing chain cover4344032
Crankshaft pulley x Crankshaft4124,200304
Transmission housing x No. 1 oil pan7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS−8
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
1996 LAND CRUISER (RM451U)
A/C compressor bracket x No. 1 oil pan
3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil check valve x Cylinder block2525018
Main bearing cap x Cylinder block
1st
2nd74
Turn 90°750
Turn 90°54
Turn 90°
Connecting rod cap x Connecting rod 1st
2nd48
Turn 90°490
Turn 90°35
Turn 90°
Rear oil seal retainer x Cylinder block2121015
Oil cooler cover x Cylinder block2121015
LH engine mounting bracket x Cylinder block6970051
LH insulator x LH engine mounting bracket7273043
RH engine mounting bracket x Cylinder brock6970051
RH insulator x RH engine mounting bracket7273043
PS pump x Cylinder block3637027
Knock sensor x Cylinder block4445033
Oil filter union x Cylinder block4445033
Drive plate x Crankshaft1001,00074
Transmission x Cylinder block7273053
Transmission x No. 1 oil pan7273053
Torque converter clutch x Drive plate5555041
A/T oil cooler pipe x Union (Transmission)3435025
Starter x Transmission3940029
Frame crossmember x Frame6162045
Frame crossmember x Engine rear mounting insulator7475054
Engine front mounting insulator x Frame7475054
Transfer shift lever x Transmission1818513
Transmission shift lever assembly x Body5.45548 in.·lbf
Transmission control rod x Control shaft lever131309
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Rear differential8890065
Rear propeller shaft x Transfer8890065
Stabillizer bar bracket mounting bolt1818513
Stabillizer bar x Axle carrier2526019
PS pressure hose x PS pump5657542
Rear TWC x Center pipe4040029
Center pipe x Tailpipe4040029
Heated oxygen sensor (Bank 1 sensor 1) x Front exhaust pipe2020014
Heated oxygen sensor (Bank 1 sensor 2) x Center pipe2020014
No. 2 support bracket x Frame18.518513
No. 3 support bracket x Frame18.518513
No. 4 support bracket x Frame18.518513
Exhaust pipe damper x Tailpipe19.519514
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EX−04
SS−16
−
SERVICE SPECIFICATIONS LUBRICATION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Oil pan x Drain plug2525018
Oil pump x Relief valve plug4950036
Drive belt idler pulley x Oil pump4344032
Oil strainer x No. 1 oil pan2020014
Baffle plate x No. 1 oil pan9.09078 in.·lbf
No. 1 oil pan x Cylinder block 14 mm head bolt
12 mm head bolt44
20440
20032
14
No. 1 oil pan x Oil pump (Timing chain cover)2020014
No. 2 oil pan x No. 1 oil pan Bolt
Nut7.8
8.880
9069 in.·lbf
78 in.·lbf
No. 1 oil pan x Transmission housing7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
A/C compressor bracket x No. 1 oil pan3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil cooler cover x Relief valve plug3737527
Oil cooler x Oil cooler cover1717012
Oil cooler cover x Cylinder block2121015
No. 1 exhaust manifold x Cylinder head3940029
No. 1 exhaust manifold x Heat insulator1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission housing2424017
Front exhaust pipe x No. 1 support bracket Clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
Oil check valve x Cylinder block2525018
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010