brakes TOYOTA LAND CRUISER 1996 J80 Workshop Manual

BR−46−
BRAKE LOAD SENSING PROPORTIONING AND BY− PASS
VALVE (LSP & BV)
1028
Author: Date:
1996 LAND CRUISER (RM451U)
5. IF NECESSARY, CHECK VALVE BODY
(a) Assemble the valve body in the uppermost position.
HINT:
When the brakes are applied, the piston will move down about
1 mm (0.039 in.). Even at this time, the piston should not make
contact with or move the load sensing spring.
(b) In this position, check the rear brake pressure.
Front brake pressure
kPa (kgf/cm2, psi)
Rear brake pressure kPa (kgf/cm2, psi)
3,434 (35, 498)3,434 (35, 498)
5,396 (55, 783)3,630 − 4,218
(37 − 43, 527 − 612)
9,810 (100, 1,424)4,513 − 5,494
(46 − 56, 655 − 797)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
MAINTENANCE INSIDE VEHICLE
MA−3
43
Author: Date:
1996 LAND CRUISER (RM451U)
13. ACCELERATOR PEDAL
Check the pedal for smooth operation and uneven pedal effort or catching.
14. BRAKE PEDAL (See page BR−6 )
(a) Check that pedal for smoothly operation.
(b) Check that the pedal has the proper reserve distance and freeplay.
(c) Check the brake booster function.
15. BRAKES
At a safe place, check that the brakes do not pull to one side when appl\
ied.
16. PARKING BRAKE (See page BR−8 )
(a) Check that the lever has the proper travel.
(b) On a safe incline, check that the vehicle is held securely with only the\
parking brake applied.
17. AUTOMATIC TRANSMISSION ”PARK” MECHANISM
(a) Check the lock release button of the selector level for proper and smoot\
h operation.
(b) On a safe incline, check that the vehicle is held securely with the select\
or lever in the P position and all brakes released.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA04W−01
−
MAINTENANCE BODY
MA−9
49
Author: Date:
1996 LAND CRUISER (RM451U)
BODY
INSPECTION
1. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten the front seat−to−body mounting bolts. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b) Under Severe Conditions: In addition to the above maintenance items, check for
loose or missing nuts and bolts on the steering system,
drive train, suspension system, fuel tank mounts, engine
mounts, etc.
2. FINAL INSPECTION
(a) Check the operation of the body parts:
Hood:
Auxiliary catch operates properly
Hood locks securely when closed
Front and rear doors:
Door locks operate properly
Doors close properly
Back door:
Door lock operates properly
Seats:
Seat adjusts easily and locks securely in any posi-
tion
Front seat back locks securely in any position
Folding −down rear seat backs look securely
(b) Road test
Check the engine and chassis for abnormal noises.
Check that the vehicle does not wander or pull to
one side.
Check that the brakes work properly and do not
drag.
(c) Be sure to deliver a clean car. Especially check the steering wheel, shift lever knob, all
switch knobs, door handles and seats.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR−18
−
STEERING TILT STEERING COLUMN
1996 LAND CRUISER (RM451U)
11. INSTALL 3 TENSION SPRINGS
12. INSTALL COMPRESSION SPRING
(a) Install the 2 bushings to the spring.
(b) Torque the bolt.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)
13. INSTALL COLUMN UPPER BRACKET AND COLUMN UPPER CLAMP
Tighten 2 new tapered −head bolts until the bolt head brakes off.
14. INSTALL WIRING HARNESS CLAMP
Tighten the bolt.
15. INSTALL COLUMN HOLE SHIELD, COLUMN HOLE COVER AND LOWER DUST SEAL
(a) Install the hole shield to the hole cover.
(b) Install the dust seal to the hole cover.
(c) Torque 2 bolts. Torque: 5.9 N·m (60 kgf·cm, 52 in.·lbf)
16. CONNECT UNIVERSAL JOINT
(a) Align the matchmarks on the intermediate No.2 shaft and
universal joint then torque the bolt.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
(b) Align the matchmarks on the universal joint and the main shaft then torque the bolt.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
17. CHECK TILT STEERING COLUMN OPERATION
(a) Check that there is no axial play at the end of the main
shaft.
(b) With the main shaft in the neutral position, raise the tilt le- ver and check that the main shaft rises to the uppermost
position.
(c) Lower the main shaft, and check that it locks in the lower-
most position.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010