TOYOTA LAND CRUISER 1998 Factory Repair Manual

SS0NL-02
- SERVICE SPECIFICATIONSPROPELLER SHAFT
SS-29
169 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Front propeller shaft x Front differential8082059
Front propeller shaft x Transfer8082059
Rear propeller shaft x Transfer1061,08078
Rear propeller shaft x Rear differential1061,08078

SS061-66
- SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
SS-45
185 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Steering wheel set nut5051037
Steering wheel pad set screw (Torx screw)8.89078 in.´lbf
Front passenger airbag assembly x Instrument panel6.06153 in.´lbf
Front passenger airbag assembly x Instrument panel reinforcement2020515
Front seat x Body4243031
Seat cushion assembly x Seat adjuster assembly2121015
Seatback cover with pad x Seatback frame4.74842 in.´lbf
Armrest x Seatback frame3738027
Seatback frame x Seat adjuster assembly4344032
Curtain shield airbag assembly x Body9.810086 in.´lbf
Airbag sensor assembly x Body17.517813
Front airbag sensor x Body7.57666 in.´lbf
Side and curtain shield airbag sensor assembly x Body2020515
Front seat outer belt x Body Upper bolt:
Lower bolt:8.0
4281
42871 in.´lbf
31
Curtain shield airbag sensor assembly x Body17.517813
Rear seat belt anchor x Body4242831
Seat position sensor assembly x Seat adjuster assembly8.08271 in.´lbf

SS0OJ-10
SS-30
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
170 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire
inflation
pressure
Tire size
P275/70R16 Front
Rear
200 kPa (2.0 kgf/cm2, 29 psi)*220 kPa (2.2 kgf/cm2, 32 psi)
220 kPa (2.2 kgf/cm2, 32 psi)*240 kPa (2.4 kgf/cm2, 35 psi)
Vehicle height
Front A - B
Rear C - D
71 mm (2.795 in.)
51 mm (2.008 in.)
Camber
Right-left error0°05' ± 45' (0.08° ± 0.75°)
30' (0.5°) or less
Fthl
Caster
Right-left error2°30' ± 45' (2.5° ± 0.75°)
30' (0.5°) or less
Front wheel
alignmentSteering axis inclination
Right-left error12°10' ± 45' (12.17° ± 0.75°)
30' (0.5°) or less
Toe-in (total)
Rack end length difference0°06' ± 12' (0.1° ± 0.2°, 1 ± 2 mm, 0.04 ± 0.08 in.)
3.0 mm (0.118 in.) or less
Wheel angle Inside wheel
Outside wheel: Reference36°42' (33°42' - 36°42')
36.7° (33.7° - 36.7°)
32°36'
32.6°
Front axle hub preload (at starting)42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)
Front axleSnap ring thickness
1.8 mm (0.0709 in.)
2.0 mm (0.0787 in.)
2.2 mm (0.0866 in.)
2.4 mm (0.0945 in.)
2.6 mm (0.1024 in.)
2.8 mm (0.1102 in.)
Front drive shaftFront drive shaft length573.9 ± 5.0 mm (22.594 ± 0.197 in.)
Ft iUpper suspension arm ball joint turning torque1.0 - 4.4 N´m (10 - 45 kgf´cm, 8.9 - 39 in.´lbf)Front suspensionLower suspension arm ball joint turning torque0.29 - 2.94 N´m (3 - 30 kgf´cm, 2.6 - 26 in.´lbf)
Bearing backlash Max.0.6 mm (0.024 in.)
RlhftAxle shaft deviation Max.0.05 mm (0.0020 in.)Rear axle shaftAxle shaft runout Max.2.0 mm (0.079 in.)
Axle shaft flange runoutMax.0.05 mm (0.0020 in.)
*: Trailer towing
A: Ground clearance of spindle center
B: Ground clearance of lower suspension arm front bolt center
C: Ground clearance of rear axle shaft center
D: Ground clearance of lower control arm front bushing center

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-31
171 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.09 mm (0.0035 in.)
Companion flange lateral runoutMax.0.09 mm (0.0035 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.0 - 1.6 N´m (10 - 16 kgf´cm, 8.9 - 14.2 in.´lbf)
0.5 - 0.8 N´m (5 - 8 kgf´cm, 4.4 - 7.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.4 - 0.6 N´m (4 - 6 kgf´cm, 3.5 - 5.3 in.´lbf)
Ring gear runout Max.0.07 mm (0.0028 in.)
Front differentialRing gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)Front differential
Side gear backlash0.05 - 0.20 mm (0.0020 - 0.0079 in.)
Differential case runout Max.0.07 mm (0.0028 in.)
Front differential oil seal drive in depth1.5 mm (0.059 in.)
Side gear thrust washer thickness
0.9 mm (0.035 in.)
1.0 mm (0.039 in.)
1.1 mm (0.043 in.)
1.2 mm (0.047 in.)
1.3 mm (0.051 in.)

SS-32
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
172 Author
: Date
:
2004 LAND CRUISER (RM1071U) Front differential
Side bearing adjusting washer thickness
2.58 mm (0.1016 in.)
2.60 mm (0.1024 in.)
2.62 mm (0.1031 in.)
2.64 mm (0.1039 in.)
2.66 mm (0.1047 in.)
2.68 mm (0.1055 in.)
2.70 mm (0.1063 in.)
2.72 mm (0.1071 in.)
2.74 mm (0.1079 in.)
2.76 mm (0.1087 in.)
2.78 mm (0.1094 in.)
2.80 mm (0.1102 in.)
2.82 mm (0.1110 in.)
2.84 mm (0.1118 in.)
2.86 mm (0.1126 in.)
2.88 mm (0.1134 in.)
2.90 mm (0.1142 in.)
2.92 mm (0.1150 in.)
2.94 mm (0.1157 in.)
2.96 mm (0.1165 in.)
2.98 mm (0.1173 in.)
3.00 mm (0.1181 in.)
3.02 mm (0.1189 in.)
3.04 mm (0.1197 in.)
3.06 mm (0.1205 in.)
3.08 mm (0.1213 in.)
3.10 mm (0.1220 in.)
3.12 mm (0.1228 in.)
3.14 mm (0.1236 in.)
3.16 mm (0.1244 in.)
3.18 mm (0.1252 in.)
3.20 mm (0.1260 in.)
3.22 mm (0.1268 in.)
3.24 mm (0.1276 in.)
3.26 mm (0.1283 in.)
3.28 mm (0.1291 in.)
3.30 mm (0.1299 in.)
3.32 mm (0.1307 in.)
3.34 mm (0.1315 in.)
3.36 mm (0.1323 in.)
3.38 mm (0.1331 in.)
3.40 mm (0.1339 in.)
3.42 mm (0.1346 in.)
3.44 mm (0.1354 in.)
3.46 mm (0.1362 in.)
3.48 mm (0.1370 in.)

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-33
173 Author
: Date
:
2004 LAND CRUISER (RM1071U) Front differential
Drive pinion bearing adjusting washer thickness
1.70 mm (0.067 in.)
1.73 mm (0.068 in.)
1.76 mm (0.069 in.)
1.79 mm (0.070 in.)
1.82 mm (0.072 in.)
1.85 mm (0.073 in.)
1.88 mm (0.074 in.)
1.91 mm (0.075 in.)
1.94 mm (0.076 in.)
1.97 mm (0.078 in.)
2.00 mm (0.079 in.)
2.03 mm (0.080 in.)
2.06 mm (0.081 in.)
2.09 mm (0.082 in.)
2.12 mm (0.083 in.)
2.15 mm (0.085 in.)
2.18 mm (0.086 in.)
2.21 mm (0.087 in.)
2.24 mm (0.088 in.)
2.27 mm (0.089 in.)
2.30 mm (0.091 in.)
2.33 mm (0.092 in.)

SS-34
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
174 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.10 mm (0.0039 in.)
Companion flange lateral runoutMax.0.10 mm (0.0039 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.3 - 1.8 N´m (13 - 19 kgf´cm, 11.5 - 15.9 in.´lbf)
0.64 - 0.92 N´m (6.5 - 9.4 kgf´cm, 5.7 - 8.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.38 - 0.63 N´m (3.9 - 6.5 kgf´cm, 3.3 - 5.6 in.´lbf)
Ring gear runout Max.0.05 mm (0.0020 in.)
Ring gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)
Side gear backlash0.02 - 0.15 mm (0.0008 - 0.0059 in.)
Differential case runout Max.0.04 mm (0.0016 in.)
Rear differential front oil seal drive in depth0.5 mm (0.020 in.)
Rear differential
Side gear thrust washer thickness
1.55 mm (0.061 in.)
1.60 mm (0.063 in.)
1.65 mm (0.065 in.)
1.70 mm (0.067 in.)
1.75 mm (0.069 in.)
1.80 mm (0.071 in.)
1.85 mm (0.073 in.)
1.90 mm (0.075 in.)
1.95 mm (0.077 in.)
2.00 mm (0.079 in.)
2.05 mm (0.081 in.)
2.10 mm (0.083 in.)
Tooth contact pattern adjusting washer thickness
1.050 mm (0.04134 in.)
1.075 mm (0.04232 in.)
1.100 mm (0.04331 in.)
1.125 mm (0.04429 in.)
1.150 mm (0.04528 in.)
1.175 mm (0.04626 in.)
1.200 mm (0.04724 in.)
1.225 mm (0.04823 in.)
1.250 mm (0.04921 in.)
1.275 mm (0.05020 in.)
1.300 mm (0.05118 in.)
1.325 mm (0.05217 in.)
1.350 mm (0.05315 in.)
1.375 mm (0.05413 in.)
1.400 mm (0.05512 in.)
1.425 mm (0.05610 in.)
1.450 mm (0.05709 in.)
1.475 mm (0.05807 in.)
1.500 mm (0.05906 in.)
1.525 mm (0.06004 in.)
1.550 mm (0.06102 in.)

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-35
175 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.10 mm (0.0039 in.)
Companion flange lateral runoutMax.0.10 mm (0.0039 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.3 - 1.8 N´m (13 - 19 kgf´cm, 11.5 - 15.9 in.´lbf)
0.64 - 0.92 N´m (6.5 - 9.4 kgf´cm, 5.7 - 8.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.3 - 0.5 N´m (3 - 5 kgf´cm, 2.7 - 4.4 in.´lbf)
Ring gear runout Max.0.05 mm (0.0020 in.)
Ring gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)
Side gear backlash0.02 - 0.15 mm (0.0008 - 0.0059 in.)
Differential case runout Max.0.04 mm (0.0016 in.)
Rear differential front oil seal drive in depth0.5 mm (0.020 in.)
Rear differential
(w/ Diff. Lock)
Side gear thrust washer thickness
1.55 mm (0.061 in.)
1.60 mm (0.063 in.)
1.65 mm (0.065 in.)
1.70 mm (0.067 in.)
1.75 mm (0.069 in.)
1.80 mm (0.071 in.)
1.85 mm (0.073 in.)
1.90 mm (0.075 in.)
1.95 mm (0.077 in.)
2.00 mm (0.079 in.)
2.05 mm (0.081 in.)
2.10 mm (0.083 in.)
(w/ Diff. Lock)
Ring gear backlash adjusting washer thickness Mark
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
2.67 mm (0.1051 in.)
2.70 mm (0.1063 in.)
2.73 mm (0.1075 in.)
2.76 mm (0.1087 in.)
2.79 mm (0.1098 in.)
2.82 mm (0.1110 in.)
2.85 mm (0.1122 in.)
2.88 mm (0.1134 in.)
2.91 mm (0.1146 in.)
2.94 mm (0.1157 in.)
2.97 mm (0.1169 in.)
3.00 mm (0.1181 in.)
3.03 mm (0.1193 in.)
3.06 mm (0.1205 in.)
3.09 mm (0.1217 in.)
3.12 mm (0.1228 in.)
3.15 mm (0.1240 in.)
3.18 mm (0.1252 in.)
3.21 mm (0.1264 in.)
3.24 mm (0.1276 in.)
3.27 mm (0.1287 in.)
3.30 mm (0.1299 in.)
3.33 mm (0.1311 in.)

SS-36
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
176 Author
: Date
:
2004 LAND CRUISER (RM1071U) Rear differential
(w/ Diff. Lock)
Tooth contact pattern adjusting washer thickness
1.050 mm (0.04134 in.)
1.075 mm (0.04232 in.)
1.100 mm (0.04331 in.)
1.125 mm (0.04429 in.)
1.150 mm (0.04528 in.)
1.175 mm (0.04626 in.)
1.200 mm (0.04724 in.)
1.225 mm (0.04823 in.)
1.250 mm (0.04921 in.)
1.275 mm (0.05020 in.)
1.300 mm (0.05118 in.)
1.325 mm (0.05217 in.)
1.350 mm (0.05315 in.)
1.375 mm (0.05413 in.)
1.400 mm (0.05512 in.)
1.425 mm (0.05610 in.)
1.450 mm (0.05709 in.)
1.475 mm (0.05807 in.)
1.500 mm (0.05906 in.)
1.525 mm (0.06004 in.)
1.550 mm (0.06102 in.)

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-37
177 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.10 mm (0.0039 in.)
Companion flange lateral runoutMax.0.10 mm (0.0039 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.3 - 1.8 N´m (13 - 19 kgf´cm, 11.5 - 15.9 in.´lbf)
0.64 - 0.92 N´m (6.5 - 9.4 kgf´cm, 5.7 - 8.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.38 - 0.63 N´m (3.9 - 6.5 kgf´cm, 3.3 - 5.6 in.´lbf)
Ring gear runout Max.0.05 mm (0.0020 in.)
Ring gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)
Side gear backlash0.02 - 0.15 mm (0.0008 - 0.0059 in.)
Differential case runout Max.0.04 mm (0.0016 in.)
Side gear thrust washer thickness (Reference)1.97 - 2.06 mm (0.0776 - 0.0811 in.)
Clutch plate thickness (Reference)1.97 - 2.03 mm (0.0776 - 0.0799 in.)
Compression spring free length (Reference)32.8 mm (1.291 in.)
Rear differential front oil seal drive in depth0.5 mm (0.020 in.)
Rear differential
(w/ LSD)
Adjusting shim thickness Mark
A
B
C
D
0.20 mm (0.0079 in.)
0.25 mm (0.0098 in.)
0.30 mm (0.0118 in.)
0.35 mm (0.0138 in.)
(w/ LSD)
Tooth contact pattern adjusting washer thickness
1.050 mm (0.04134 in.)
1.075 mm (0.04232 in.)
1.100 mm (0.04331 in.)
1.125 mm (0.04429 in.)
1.150 mm (0.04528 in.)
1.175 mm (0.04626 in.)
1.200 mm (0.04724 in.)
1.225 mm (0.04823 in.)
1.250 mm (0.04921 in.)
1.275 mm (0.05020 in.)
1.300 mm (0.05118 in.)
1.325 mm (0.05217 in.)
1.350 mm (0.05315 in.)
1.375 mm (0.05413 in.)
1.400 mm (0.05512 in.)
1.425 mm (0.05610 in.)
1.450 mm (0.05709 in.)
1.475 mm (0.05807 in.)
1.500 mm (0.05906 in.)
1.525 mm (0.06004 in.)
1.550 mm (0.06102 in.)