ESP TOYOTA LAND CRUISER 1998 Factory Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1998, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1998Pages: 3115, PDF Size: 54.88 MB
Page 166 of 3115
I25054
ºTUNE DOWNº
Switchº4chº Switchº5chº Switch
º6chº Switch
ºTUNE UPº
Switch º1chº Switch
º2chº Switchº3chº Switch
ºDISCº Switch
BE-130
- BODY ELECTRICALAUDIO SYSTEM
2503 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) Service check mode
(1) After the element check and switch check is completed, the system enters service check mode
when ºTUNE UPº switch is pressed.
(2) Error codes over the tuner and connected equipments are displayed on the screen of the tuner.
Results for each check are displayed as follows:
good:
No DTC is detected for both ºSystem Check Confirmationº and ºDiagnosis Memory Re-
sponseº.
nCon:
The component does not respond to the ºDiagnosis On Instructionº command.
Applicable to only the system where connected components are limited to be used.
ECHn:
Application of new version has been confirmed by the ºDiagnosis On Checkº, and there
is one or more DTC which indicates ºReplacementº in the ºSystem Check Result Re-
sponseº or ºDiagnosis Memory Responseº.
CHEC:
Application of new version has been confirmed by the ºDiagnosis On Checkº, and there
is no DTC which indicates ºReplacementº in the ºSystem Check Result Responseº or
ºDiagnosis Memory Responseº, but one or more DTC which indicates ºCheckº is identified.
Old:
Application of old version is confirmed by the ºDiagnosis On Checkº, and DTC is identified
in the ºSystem Check Result Responseº or ºDiagnosis Memory Responseº.
nrES:
No response is identified to the ºSystem Check Start Instructionº and ºRequest for System
Check Resultº commands.
HINT:
Check the present and past condition of components by performing the System Check and collecting
stored DTC memories.
Check results are displayed as one of the following six indications: ºgoodº, ºECHnº, ºCHECº,ºnConº,
ºOldº or ºnrESº.
Page 172 of 3115
I25241
ºTUNE DOWNº Switch
ºTUNE UPº Switch
BE-136
- BODY ELECTRICALAUDIO SYSTEM
2509 Author: Date:
2004 LAND CRUISER (RM1071U)
(c) Service check mode
(1) After the element check and switch check is completed, the system enters service check mode
when ºTUNE UPº switch is pressed.
(2) Error codes over the tuner and connected equipments are displayed on the screen of the tuner.
Results for each check are displayed as follows:
good:
No DTC is detected for both ºSystem Check Confirmationº and ºDiagnosis Memory Re-
sponseº.
nCon:
The component does not respond to the ºDiagnosis On Instructionº command.
Applicable to only the system where connected components are limited to be used.
ECHn:
Application of new version has been confirmed by the ºDiagnosis On Checkº, and there
is one or more DTC which indicates ºReplacementº in the ºSystem Check Result Re-
sponseº or ºDiagnosis Memory Responseº.
CHEC:
Application of new version has been confirmed by the ºDiagnosis On Checkº, and there
is no DTC which indicates ºReplacementº in the ºSystem Check Result Responseº or
ºDiagnosis Memory Responseº, but one or more DTC which indicates ºCheckº is identified.
Old:
Application of old version is confirmed by the ºDiagnosis On Checkº, and DTC is identified
in the ºSystem Check Result Responseº or ºDiagnosis Memory Responseº.
nrES:
No response is identified to the ºSystem Check Start Instructionº and ºRequest for System
Check Resultº commands.
HINT:
Check the present and past condition of components by performing the System Check and collecting
stored DTC memories.
Check results are displayed as one of the following six indications: ºgoodº, ºECHnº, ºCHECº,ºnConº,
ºOldº or ºnrESº.
Page 177 of 3115
Physical address: 190 Radio receiver assembly
Diagnosis item
ROM Error
Absence of
MasterDiagnosis contentCountermeasure and
inspected parts
Error is detected in internal ROM. Logical address
01
(Communication
Control)
01 *2
(Communication
Control)Component in which this code is re-
corded has been disconnected from
system with ignition in ACC or ON.
Or, when this code was recorded, ra-
dio receiver assembly was discon-
nected. Check harness for power supply
system of radio receiver assembly.
Check harness for communica-
tion system of radio receiver as-
sembly.
DTC
21
D6Replace radio receiver assembly.
RAM Error Error is detected in internal RAM. 01
(Communication
Control)22Replace radio receiver assembly.
No Response
to Connection
Check 01 *3
(Communication
Control)Component shown by auxiliary code
is or had been disconnected from
system after engine start.
D9 Check harness for power supply
system of component shown by
auxiliary code.
Check harness for communica-
tion system of component shown by
auxiliary code. D8
Last Mode Error 01 *2
(Communication
Control)Component operated (sounds and/
or images were provided) before en-
gine stop is or has been discon-
nected with ignition switch in ACC or
ON. Check harness for power supply
system of component shown by
auxiliary code.
Check harness for communica-
tion system of component shown by
auxiliary code. D9
No Response
to ON/OFF
InstructionNo response is identified when
changing mode (audio and visual
mode change). Detected when
sound and picture does not change
by button operation. DA 01
(Communication
Control) Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
If error occurs again, replace
component shown by auxiliary
code.
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Mode Status
Error DB 01 *2
(Communication
Control)Dual alarm is detected. Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
- BODY ELECTRICALAUDIO SYSTEM
BE-141
2514 Author: Date:
2004 LAND CRUISER (RM1071U)
3. DIAGNOSIS CODE LIST
w/ Navigation system (See page)
Page 182 of 3115
No Response
to Connection
Check 01 *3
(Communication
Control)Component shown by auxiliary code
is or had been disconnected from
system after engine start.
D9 Check harness for power supply
system of component shown by
auxiliary code.
Check harness for communica-
tion system of component shown by
auxiliary code. D8
Last Mode Error 01 *2
(Communication
Control)Component operated (sounds and/
or images were provided) before en-
gine stop is or has been discon-
nected with ignition switch in ACC or
ON. Check harness for power supply
system of component shown by
auxiliary code.
Check harness for communica-
tion system of component shown by
auxiliary code. D9
No Response
to ON/OFF
InstructionNo response is identified when
changing mode (audio and visual
mode change). Detected when
sound and picture does not change
by button operation. DA 01
(Communication
Control) Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
If error occurs again, replace
component shown by auxiliary
code.
Mode Status
Error DB 01 *2
(Communication
Control)Dual alarm is detected. Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
Physical address: 16A, 16C RSA Panel (Sub AVC-LAN)
Transmission
Error DC 01 *4
(Communication
Control)Transmission to component shown
by auxiliary code has been failed.
(Detecting this DTC does not nec-
essary mean actual failure.) If same auxiliary code is recorded
in other component, check harness
for power supply and communica-
tion system of components shown
sub code.
Slave Reset
(Momentary
Interruption) DE 01 *3
(Communication
Control)After engine is started, slave com-
ponent was disconnected from sys-
tem. Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Logical addressDTC
Diagnosis itemDiagnosis content
Countermeasure and inspeced parts
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
BE-146
- BODY ELECTRICALAUDIO SYSTEM
2519 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 353 of 3115
I20456
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or
rolling code.
0.13secs.
0.5secs.
0.13secs. 0.25secs. 0.5secs.
0.5secs. 0.5secs.
OFF ON
OFF ON
OFF ON
OFF ON
While receiving
I04149
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-101
2474 Author: Date:
2004 LAND CRUISER (RM1071U)
(c) Diagnosis Mode Check.
HINT:
Check how the taillight lights up when pressing each transmitter
switch.
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or rolling code.
HINT:
If (4) is detected in the Diagnosis Check, conduct the recogni-
tion code registration.
(5) No response from the taillight.
HINT:
Conduct the following checks.
Wireless door lock transmitter.
Wireless door lock receiver.
4. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control receiver and transmitter re-
placementº.
(a) Using a screwdriver, remove the screw and cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (-) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
(e) Install the battery (lithium battery).
(f) Install a cover so that O-ring is not distorted or slipped off.
(g) Using a screwdriver, tighten the screw.
Standard:
Remote control of vehicle door lock can be operated.
LED lights up more than once.
HINT:
The minimum operation distance differs according to op-
erator, the way of holding, and location.
Page 354 of 3115
I04150
I07522
BE-102
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2475 Author: Date:
2004 LAND CRUISER (RM1071U)
As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
5. CHECK BATTERY CAPACITY
HINT:
Make sure to use the TOYOTA electrical tester.
With the battery unloaded, judge can not be made wheth-
er the battery is available or not on the test.
When the transmitter is faulty, the energy amount left in
the battery might not be checked correctly.
On the lithium battery used for the transmitter, the voltage
more than 2.5 V with the battery unloaded is shown on the
tester until the energy is completely consumed.
Accordingly when inspecting the energy amount left in the
battery, it is necessary to measure the voltage when the
battery is loaded. (1.2 kW).
(a) Remove the 2 screws and cover using a (-) driver.
(b) Remove the battery (lithium battery) from the transmitter.
(c) Connect the lead to the (-) terminal of the transmitter and
install the battery.
(d) Connect the (+) tester to the (+) battery (lithium battery),
and (-) tester to the lead respectively.
(e) Press one of the transmitting switches on the transmitter
for approx. 1 second.
(f) Press the transmitting switch on the transmitter again to
check the voltage.
Standard: 2.1 V or more
HINT:
When the temperature of the battery is low, the judge can
not be made correctly.
When the outcome of the test is less than 2.1 V, conduct
the test again after leaving the battery in the place at 18
°C for more than 30 minutes.
By auto power off function, the voltage becomes no load
voltage (more than 2.5 V) condition 20 seconds after the
switch was pressed.
Make sure to read the voltage before of it.
Page 360 of 3115
Close"open"close"open
START
The vehicle should be in the following conditions:
Driver door open (Other doors are closed).
Insert and remove the key into/from the ignition cylinder twice.
Insert"remove "insert"remove
HINT: If the IG switch operation is
not performed with the specified
number of times (If it is 4 times, 6
times or more), this operation is
finished with no response.
HINT: The registration operation is
cancelled if each operation is not
completed within the specified
time.
No key inserted in the IG key cylinder.
Close and open the driver door twice.
Close"open"close"open
Insert and remove the key into/from the ignition cylinder once.
Insert"remove
Insert the key into the ignition key cylinder.
Close all the doors.
Mode Selection
Turn the IG SW ON
u"LOCK once.Add modeTurn the IG SW ON
u"LOCK twice.Rewrite modeTurn the IG SW ON
u"LOCK 3 times. Confirmation modeTurn the IG SW ON
u"LOCK 5 times. Prohibition mode
Remove the key from the IG key cylinder.
Within 5 sec.
Within 40 sec.
Within 40 sec.
Within 40 sec.
Close and open the driver door twice.
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-95
2468 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) By Switch Operation:
Page 361 of 3115
Add mode: Response of whether or not being moved to each mode is given with
the number of times of door lock working (lock/unlock).
Within 3 sec.
Within 40 sec.
Within 3 sec. Rewrite mode:
Confirmation mode:
Prohibition mode:once*1
twice*1
The number of times equivalent to the number
of currently registered codes*2
5 times*1
HINT: The confirmation mode and the prohibition mode are finished
after the responses.
Transmitter SW Operation:
Press both lock and unlock SW. (Between 1 and 1.5 sec.)
Press any one of SW. (For more than 1 sec.)
Response of whether or not the registration is completed is given in the
form of the number of times of door lock operations (lock/unlock opera-
tion).
Register other transmitters?
or
Finish the registration?
Finish the registration.
Within 3 sec.Confirmation mode
Prohibition mode
END Add mode,
Rewrite mode
When registration is completed:
When registration is not completed:once*1
twice*1
Insert the key into the IG key cylinder. Perform one of the following operations to finish the Add mode and the
Rewrite mode.
Open any one of the doors.
Wait for 40 sec. after the code registration.
HINT: In case of registering 4 codes at a time, the mode will be finished
when the 4
th code is registered. Continue
the registration.
Within 40 sec. BE-96
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2469 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 414 of 3115
H21419
Shape
Size
ShapeSizeShape
Size
ù = 8
L =16
(0.63) (0.31)ù = 6
L =18
(0.71) (0.24)ù = 6
L =16
(0.63) (0.24)
ù = 6
L =16
(0.63) (0.24)ù = 5
L =16
(0.63) (0.20)
ù = 5
L =14
(0.55)(0.20)
ù = 6
(0.24)ù = 8
(0.31) mm (in.)
ù = 5
L =14
(0.55) (0.20)
Jù = 6
L =11
(0.43) (0.24)
IH
F
G
CBA
ED
- BODYINSTRUMENT PANEL
BO-83
2657 Author: Date:
2004 LAND CRUISER (RM1071U)
HINT:
Screw shapes and sizes are indicated in the table below. The codes (ºAº to ºIº) correspond to those indicated
on the previous page.
Page 842 of 3115
F02840
ABS Motor 1
Relay
2
2ABS
Motor 2
Relay
Motor Relay322
3
ECU7
MT
DI-590- DIAGNOSTICSABS & VEHICLE STABILITY CONTROL (VSC) &
BRAKE ASSIST (BA) SYSTEM
783 Author: Date:
2004 LAND CRUISER (RM1071U)
NG Replace ABS motor 1 relay or ABS motor 2
relay.
OK
5 Check continuity between terminal MT of the ABS & BA & TRAC & VSC ECU and
terminals BM1 and BM2, respectively.
PREPARATION:
Disconnect the 2 connectors from the hydraulic brake booster.
CHECK:
(a) Check continuity between terminal BM1 of the ABS motor
2 relay and terminal MT of the ABS & BA & TRAC & VSC
ECU.
(b) Check continuity between terminal BM2 of the ABS motor
1 relay and terminal MT of the ABS & BA & TRAC & VSC
ECU.
OK:
Continuity
HINT:
There is resistance of 33 ± 3 W between terminal BM1or BM2
and MT of the hydraulic brake booster.
NG Repair or replace harness, connector or hy-
draulic brake booster.
OK