brake sensor TOYOTA PRIUS 2001 Service Owner's Manual

THS (TOYOTA HYBRID SYSTEM)
Shift Position
Sensor
182TH05
Accelerator
Pedal Position
Sensor
BRAKE
ECU
Shift Position
(Main and Sub)
Accelerator Angle
(Main and Sub)
Regenerative
Request FactorHV ECUInverter
Voltage
SMR Control
MG2MG1
RPMEngine
Power
RequestCharging
Condition,
Amperage
SMRSMR
Amperage
HV
Battery Engine
Planetary Gear
Unit
Wheel
Wheel
ECM
Battery
ECU
Hydraulic
Brake
Actual
Regenerative
Braking Factor
Auxiliary
Battery
Mechanical Power Path
Electrical Signal Hydraulic
Converter
25

SYSTEM DIAGRAM

THS (TOYOTA HYBRID SYSTEM)27
THS CONTROL SYSTEM
1. General
The THS control system contains the following components:
HV (Hybrid Vehicle
Control) ECU
Controls the MG1, 2 and the engine according to the demand torque,
regenerative brake control and the SOC (state of charge) of HV battery. These
factors are determined by the shift position, the degree which the accelerator
is depressed, and vehicle speed.
ECM
ControlThe HV ECU receives engine status data (rpm, torque) from the ECM and
determines the engine demand torque.
Moreover, engine stop and fuel cut signals are sent according to the driving
conditions.
In addition, the vehicle speed signal received from the combination meter is
also sent.
BRAKE
ECU
ControlThe HV ECU receives data corresponding to the total braking force needed.
The HV ECU transmits the regeneration brake demand torque valve, as well
as the regeneration brake execution torque valve.
Inverter
(for MG1,
MG2)
ControlThe HV ECU sends the signal to the power transistor in the inverter for
switching the U, V, W, phase of the MG1, 2 in order to drive the MG1 and 2.
Moreover, if an overheating, overcurrent or fault voltage signal is received
from the inverter, it is shut down.
ConverterWhen a malfunction is in the Hybrid vehicle control system, the HV ECU
sends a signal to the converter, and the converter is stopped.
MG1, MG2Detects the position of the rotor of the MG1, 2 and controls the current flowing
to the MG1, 2.
In addition, the temperature is detected and the maximum load is controlled.
Battery ECUReceives the SOC of the HV battery and the current value.
Airbag Sensor
AssemblyReceives the airbag deployment signal.
A / C ECUReceives the engine power rise demand (when air-conditioning is turned ON)
and the engine running demand for water-temperature maintenance.
Accelerator Pedal
Position SensorReceives the value corresponding to degree at which the accelerator pedal is
depressed.
Shift Position SensorReceives the shift position signal (P, R, N, D, B).
Cruise Control SwitchReceives the cruise control switch signal.
Stop Light SwitchReceives the brake signal.
Interlock Switch
(for Inverter Cover and
Service Plug)Verifies that the cover of both the inverter and the service plug have been
installed.
Circuit Breaker SensorThe high-voltage circuit is intercepted if a vehicle collision has been detected.
DiagnosisWhen the HV ECU detects a malfunction, the HV ECU diagnosis and
memorizes the values corresponding to the failure.
Fail-SafeWhen the HV ECU detects a malfunction, the HV ECU stops or controls the
actuators and ECUs according to the data already stored in memory.

THS (TOYOTA HYBRID SYSTEM)
HV ECUGO
ECM
Engine
Throttle Control
Motor
SPDO
EF1
HTE, ETH
ESA
VVT-i
W
MESTP
Brake Actuator
(Brake Master
Cylinder)
BRAKE ECUBrake Actuator
(Solenoid Valves)
Pressure Sensors
Signal
HV ECU Pressure
BTH
Total Brake Force
RequestedHTB
Regenerative Brake
Force Transmitted29
3. ECM Control
The ECM receives the demand torque and the target rpm which were sent from HV ECU (THE, ETH), and
controls the degree of throttle valve opening, fuel injection timing, ignition time and VVT-i.
In addition, the actual rpm is sent to the HV ECU with GO, and the speed signal from the hybrid transaxle
is received through HV ECU with SPDO.
When the vehicle is stopped, the HV ECU may send an engine stop (ESTP) command to the ECM to reduce
fuel used.
When a malfunction occurs in the system, the ECM activates MIL via the directions from the HV ECU.
4. BRAKE ECU Control
The brake ECU calculates the total braking force needed, based on the master cylinder pressure in the brake
actuator generated when the driver depresses the brake pedal, and sends this valve to the HV ECU.
The HV ECU computes a part for the regeneration brake force from the total braking force, and sends the
result to the brake ECU.
The HV ECU executes to the minus torque to MG2, and carries out the regenerative brake functions.
The brake ECU controls the brake actuator solenoid valves and generates the wheel cylinder pressure, which
is the regenerative brake force subtracted from the total braking force.

THS (TOYOTA HYBRID SYSTEM)
182CH05
Stator
Rotor
Speed Sensor (Resolver)
MG1
182CH04
Stator
Rotor
Speed Sensor (Resolver)
MG2
182TH07
N.m
350
300
250
200
150
100
50
0
01000 30002000 50004000 60000 20 40
30
10 kW
Torque
Engine Speed (rpm)Output
Torque
Output
33
MG1 AND MG2 (MOTOR GENERATOR NO.1 AND NO.2)
DESCRIPTION
Both the MG1 and the MG2 are compact, lightweight, and highly efficient alternating current permanent
magnet synchronous type.
Serving as the source of supplemental motive force that provides power assistance to the engine as needed,
the electric motor helps the vehicle achieve excellent dynamic performance, including smooth start-offs
and acceleration. When the regenerative brake is activated, MG2 converts the vehicle's kinetic energy into
electrical energy, which is then stored in the HV battery.
MG1 recharges the HV battery and supplies electrical power to drive MG2. In addition, by regulating the
amount of electrical power generated (thus varying the generator's rpm), MG1 effectively controls the
continuously variable transmission function of the transaxle. MG1 also serves as the starter to start the
engine.

MG2 Specifications 
TypePermanent Magnet
Motor (1CM)
Rated voltage [V]273.6
Maximum output [kW] (rpm)33 / (1040
5600)
Maximum torque [N.m (kgf.m) (rpm)350 / (0
400)
Amperage at maximum torque [A]351
Cooling systemWater-cooled

Performance Curve 

CHASSIS ± BRAKES
182CH44
Front
Brake ActuatorRear
Hydraulic
Brake
Differential
Gear
Stroke
Simulator
Hydraulic
Adjustment Area
ABS Function AreaHydraulic
Brake
MG2
MG1Inverter
EngineHV Battery
THS (TOYOTA Hybrid System) Regenerative
Brake
Switching
Valve
Power Splitting
Device
182CH45
Combination Meter
Brake ECU
Brake Warning Buzzer
Rear Wheel
Speed Sensors
and Rotors
Hydraulic Brake Booster
(Master Cylinder Portion)
Front Wheel Speed
Sensor and Rotor
Brake Actuator HV ECU
Hydraulic Brake
Booster
Power Supply
portion
Solenoid RelayReservoir
Tank
ECMPump
Motor Relays 104
BRAKE SYSTEM
1. General

A brake system, which uses brake fluid that is stored under high pressure to assist the brake pedal effort
and to operate the ABS with EBD control and the regenerative brake cooperative control, has been adopted.

A regenerative brake system, which uses the MG2 that is used for driving the vehicle as a generator to effi-
ciently convert the energy that is created during braking, has been adopted. This system enables to collect
more driving energy by having the control to cooperate the hydraulic brake and the regenerative brake.
2. System Diagram
3. Layout of Main Components

CHASSIS ± BRAKES105
4. Function of Main Components
ComponentsFunction
ABS Warning
LightLights up to alert the driver when the brake ECU detects the
malfunction in the ABS.
Combination
Meter
Brake System

Lights up together with the ABS warning light to alert the driver
when the brake ECU detects the malfunction not only in the ABS
but also in the EBD controlBrake System
Warning Lightbut also in the EBD control.

Lights up to alert the driver when the malfunction occurs in the
brake system.
Stop Light SwitchDetects the brake depressing signal.
Brake Warning BuzzerEmits a continuous sound to inform the driver that the ABS ECU
detects the malfunction in the hydraulic brake booster.
Speed SensorsDetect the wheel speed of each of the four wheels.
Brake ECU

Processes various sensor signals, regenerative brake signals, to
execute control of the ABS control, EBD control, regenerative
coordination control and hydraulic brake booster.

Communicates control data with the HV ECU.
HV ECUMaintains serial communication with the brake ECU to exchange
regenerative coordination control signals.
Hydraulic Brake Booster
Assists with the pedal effort applied to the brake pedal.

Supplies hydraulic pressure.
Brake ActuatorControls the brake fluid pressure to each brake wheel cylinder by
signals from the brake ECU.
Solenoid RelaySupplies power to the ABS's solenoid valve's in the brake actuator.
Pump Motor RelaysControl the pump motor operation in the hydraulic brake booster.

CHASSIS ± BRAKES
182CH46
SMC1
SMC2
SS
SLA
SLRSFRH
SFRR
SFLH
SFLR
SRrH
SRrRABS Solenoid Valves Switching Solenoid Valves
Linear Solenoid Valves
Hydraulic Brake BoosterAccumulator
Pump and
Pump
Motor
Pressure Switch PH
Pressure Switch PL
Master Cylinder and
Brake Booster
Brake Actuator
Pressure
Sensor
SLR
SLA
Reservoir
Pressure
Sensor
P & B Valve
Rear Wheel CylindersSRrH
SRrRSS
SMC1 SMC2
Pressure
Sensor
Front Wheel CylindersPressure
Sensor
Stroke
Simulator
SFRH
SFRR
SFLRSFLH 106
5. Hydraulic Circuit

CHASSIS ± BRAKES107
6. Construction and Operation
The brake system of Prius consists of the following components:
Components
Function
Pump and Pump Motor
Draws up the brake fluid from the reservoir tank
and provides high hydraulic pressure to the
accumulator.
Accumulator
Stores the hydraulic pressure that was generated
by the pump. The accumulator is filled with
highpressure nitrogen gas.
Power
Supply
PortionPressure Switches
Monitors the hydraulic pressure of the
accumulator and outputs control signals for the
pump motor.
There are two types: the pressure switch PH for
controlling the pump, and the pressure switch PL
for giving a warning when the pressure is low.
Hydraulic
Brake
Booster
Relief Valve
Returns the brake fluid to the reservoir tank to
prevent excessive pressure if the pump operates
continuously due to a malfunction of the pressure
switch.
Reservoir TankStores the brake fluid.
Brake Fluid Level
Warning SwitchDetects the low brake fluid level.
Master
Master Cylinder
Generates the hydraulic pressure in accordance
with the pedal effort that is applied to the brake
pedal.
Master
Cylinder
Portion
Brake Booster
Regulates the accumulator pressure in accordance
with the pedal effort that is applied to the brake
pedal and introduces this pressure to the boosterBrake Boosterpedal and introduces this pressure to the booster
chamber in order to provide a power assist to the
brakes.
Pressure SensorsDetects the pressure of the master cylinder,
regulator, and front and rear wheel cylinders.
Switching
Solenoid ValvesSwitches the hydraulic path between normal
braking and braking under control.
Brake
Actuator
ABS Control Solenoid
Valves
Pressure Holding
Valves
Pressure Reduction
Valves
Controls the hydraulic pressure that is applied to
the wheel cylinders during ABS control or EBD
control.
Actuator
Linear Solenoid Valve
Regulates the hydraulic pressure to the wheel
cylinders during braking in accordance with the
fluctuations in the regenerative brake force.
Reservoir
Temporarily stores the brake fluid when
regulating the hydraulic pressure to the wheel
cylinders in accordance with the fluctuations in
the regenerative brake force.
Stroke SimulatorGenerates a pedal stroke during braking in
accordance with the driver's pedal effort.

CHASSIS ± BRAKES
182CH52
Spring
for 1st
Stage
Spring
for 2nd
StageTo
ReservoirStroke
Simulator
Full Stroke
Pedal Stroke 2nd Stage
Spring
Characteristics
1st Stage +
2nd Stage
Spring
Characteristics
Master Cylinder Hydraulic Pressure From
Master
Cylinder
182CH53
From wheel Cylinder (SLR)
182CH54
11 4
4) Stroke Simulator
The stroke simulator generates a pedal stroke in accordance with the driver's pedal effort during braking.
Containing 2 types of coil springs with different spring constants, the stroke simulator provides pedal
stroke characteristics in 2 stages in relation to the master cylinder pressure.
5) Reservoir
Temporarily stores the brake fluid to absorb
the pressure when regulating the wheel cylin-
der pressure.
6) Pressure Sensors
Mounted on the brake actuator, the pressure
sensor linearly detects the pressure that is gen-
erated in the master cylinder, regulator, and
the front and rear wheel cylinders and outputs
them to brake ECU.

CHASSIS ± BRAKES
182CH55
Speed Sensors
Combination Meter
Speedometer
ABS Warning Light
Brake System Warning
Light
Brake Warning Buzzer
Stop Light Switch
ECM
HV ECU
Inverter
Battery ECU
Brake
ECU
Solenoid Relay
Motor Relay
Brake Actuator
ABS Solenoid
Valves
Switching Solenoid Valve
Linear Solenoid Valve
Master Cylinder Pressure
Sensor
Regulator Pressure Sensor
Front Wheel Pressure Sensor
Rear Wheel Pressure Sensor
Pump Motor
High Pressure Switch
Low Pressure Switch
Reservoir Level Switch
Hydraulic Brake Booster11 5
Brake ECU
1) General
Based on the signals received from the sensors the communication it maintains with the HV ECU, the
brake ECU effects conventional brake control, ABS with EBD control, and regenerative brake coopera-
tive control.
2) Fail Safe
If a malfunction occurs in the brake ECU, in the input signals from the sensors, or in actuator system,
this function prohibits the current from flowing to the brake actuator.
As a result, the solenoids in the brake actuator turn off, enabling the braking force of the hydraulic brake
to take effect. Furthermore, by illuminating the ABS warning light or the brake system warning light,
this function alerts the driver that a malfunction exists in the system.
Only if the regenerative brake system cannot be used, such as in the case of a malfunction in the commu-
nication with the HV ECU, this function switches controls to enable the hydraulic brake to generate the
entire brake force.
3) Warning Light Check Function
The ABS warning light and brake system warning light turns on for about 3 seconds after the ignition
switch is turned on to check the circuit.