wiring diagram TOYOTA RAV4 2006 Service User Guide

TIRE AND WHEEL – TIRE PRESSURE WARNING SYSTEMTW–29
TW
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure warning antenna and
receiver and/or the tire pressure warning ECU (see page TW-9).
(a) Set the pressure of each tire to the specified value.
Standard pressure:
220 kPa (2.2 kgf/cm
2, 32 psi)
(b) Connect the intelligent tester (with CAN VIM) to the
DLC3.
(c) Turn the ignition switch ON.
(d) Select TIREPRESS by following the prompts displayed
on the intelligent tester.
Tire pressure warning ECU
1PERFORM FORCED TRANSMISSION OF TRANSMITTER ID OF ALL WHEELS
E118453E14
Item Measurement item / Range
(Display) Normal Condition Diagnostic Note
TIREPRESS1 ID1 tire pressure / min.: 0 kPa
(0 kgf/cm
2, 0 psi), max.: 637.5
kPa (6.48 kgf/cm2, 92.2 psi) Actual tire pressure -
TIREPRESS2 ID2 tire pressure / min.: 0 kPa
(0 kgf/cm
2, 0 psi), max.: 637.5
kPa (6.48 kgf/cm2, 92.2 psi) Actual tire pressure -
TIREPRESS3 ID3 tire pressure / min.: 0 kPa
(0 kgf/cm
2, 0 psi), max.: 637.5
kPa (6.48 kgf/cm2, 92.2 psi) Actual tire pressure -

TW–32TIRE AND WHEEL – TIRE PRESSURE WARNING SYSTEM
TW
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure warning valve and
transmitter and/or the tire pressure warning ECU (see page TW-9).
(a) Set the pressure of each tire to the specified value.
Standard pressure:
220 kPa (2.2 kgf/cm
2, 32 psi)
(b) Connect the intelligent tester (with CAN VIM) to the
DLC3.
(c) Turn the ignition switch ON.
(d) Select TIREPRESS by following the prompts displayed
on the intelligent tester.
Tire pressure warning ECU
1IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
E118453E14
Item Measurement Item / Range
(Display)Normal Condition Diagnostic Note
TIREPRESS1 ID1 tire pressure/ minimum: 0
kPa (0 kgf/cm
2, 0 psi)
maximum: 637.5 kPa (6.5 kgf/
cm
2, 92.5 psi)Actual tire pressure -
TIREPRESS2 ID2 tire pressure/ minimum: 0
kPa (0 kgf/cm
2, 0 psi)
maximum: 637.5 kPa (6.5 kgf/
cm
2, 92.5 psi)Actual tire pressure -
TIREPRESS3 ID3 tire pressure/ minimum: 0
kPa (0 kgf/cm
2, 0 psi)
maximum: 637.5 kPa (6.5 kgf/
cm
2, 92.5 psi)Actual tire pressure -

POWER STEERING – ELECTRONIC POWER STEERING SYSTEMPS–21
PS
DESCRIPTION
The torque sensor converts the rotation torque input from the steering wheel into electric signals and
sends them to the power steering ECU.
WIRING DIAGRAM
DTC C1511/11 Torque Sensor 1 Malfunction
DTC C1512/11 Torque Sensor 2 Malfunction
DTC C1513/11 Torque Sensor Deviation Excessive
DTC C1514/11Torque Sensor Power Supply Voltage Malfunc-
tion
DTC No. DTC Detection Condition Trouble Area
C1511/11 Torque sensor malfunction • Torque sensor (built into steering column
assembly)
• Power steering ECU
• Connector C1512/11
C1513/11
C1514/11
C128931E01

POWER STEERING – ELECTRONIC POWER STEERING SYSTEMPS–25
PS
DESCRIPTION
The power steering ECU supplies the current to the power steering motor through the motor circuit.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Connect the intelligent tester (with CAN VIM) to the
DLC3.
(b) Turn the ignition switch ON and press the intelligent
tester main switch ON.
(c) Select the items "MTR TERMINAL(U)", "MTR
TERMINAL(V)", "MTR TERMINAL(W)" in the DATA LIST
and read the value displayed on the intelligent tester.
Power steering ECU
DTC C1524/24 Motor Terminal Voltage Malfunction
DTC No. DTC Detection Condition Trouble Area
C1524/24 Short (or open) in motor circuit or abnormal
voltage or current in motor circuit• Steering column assembly
• Power steering ECU
1READ VALUE OF INTELLIGENT TESTER (MOTOR VOLTAGE)
C128932E01
Item Item Description: Range
(Display)Inspection Condition Reference Value
MTR TERMINAL(U) Motor terminal voltage (U phase):
Min.: 0 V
Max.: 46.667 VSteering wheel is turned While turning the steering wheel,
a value within the range of 1 V to
approximately 0.7 V less than the
battery voltage is displayed. (The
value changes according to the
steering load.)

POWER STEERING – ELECTRONIC POWER STEERING SYSTEMPS–27
PS
DESCRIPTION
The motor rotation angle sensor detects the motor rotation angle and sends this information to the power
steering ECU.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Check the installation condition of the motor rotation
angle sensor connector.
OK:
Motor rotation angle sensor connector is securely
connected to the power steering ECU.
Result
DTC C1528/12 Motor Rotation Angle Sensor Malfunction
DTC No. DTC Detection Condition Trouble Area
C1528/12 Motor rotation angle sensor malfunction • Steering column assembly
• Power steering ECU
1CHECK CONNECTOR CONNECTION CONDITION
C128934E01
Result Proceed to
NG A
OK B

PS–30POWER STEERING – ELECTRONIC POWER STEERING SYSTEM
PS
DESCRIPTION
The power steering ECU distinguishes the ignition switch status as ON or OFF through the IG power
source circuit.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Connect the intelligent tester (with CAN VIM) to the
DLC3.
(b) Turn the ignition switch ON.
(c) Select the item "IG SUPPLY" in the DATA LIST and read
the value displayed on the intelligent tester.
Power steering ECU
OK
NG
DTC C1551/25 IG Power Supply Voltage Malfunction
DTC No. Detection Condition Trouble Area
C1551/25 IG power source circuit malfunction inside
ECU• ECU-IG1 fuse
• IG power source circuit
• Power steering ECU
1READ VALUE OF INTELLIGENT TESTER (IG POWER SUPPLY)
B128053E03
Item Item Description: Range
(Display)Inspection Condition Specified Condition
IG SUPPLY IG power supply:
Min.: 0 V
Max.: 20.1531 VIgnition switch ON 10 to 14 V
CHECK INTERMITTENT PROBLEMS

PS–32POWER STEERING – ELECTRONIC POWER STEERING SYSTEM
PS
DESCRIPTION
When a problem occurs in the system, the power source relay circuit is shut off to stop the power assist.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Connect the intelligent tester (with CAN VIM) to the
DLC3.
(b) Turn the ignition switch ON.
(c) Select the item "PIG SUPPLY" in the DATA LIST and
read the value displayed on the intelligent tester.
Power steering ECU
OK
NG
DTC C1552/22 PIG Power Supply Voltage Malfunction
DTC No. DTC Detection Condition Trouble Area
C1552/22 PIG power source circuit malfunction inside
ECU• PIG power source circuit
• Power steering ECU
1READ VALUE OF INTELLIGENT TESTER (PIG POWER SUPPLY)
B128054E05
Item Item Description: Range
(Display)Inspection Condition Specified Condition
PIG SUPPLY PIG power supply:
Min.: 0 V
Max.: 20.1531 VPower steering in operation 10 to 14 V
CHECK INTERMITTENT PROBLEMS

SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEMRS–61
RS
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Turn the ignition switch OFF.
(b) Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the
center airbag sensor and the front airbag sensor RH.
OK:
The connectors are connected.
NG
1CHECK CONNECTION OF CONNECTOR
C123527E01
CONNECT CONNECTOR

RS–72SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM
RS
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Turn the ignition switch OFF.
(b) Disconnect the cable from the negative (-) terminal, and
wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the
center airbag sensor and the front airbag sensor LH.
OK:
The connectors are properly connected.
NG
OK
1CHECK CONNECTION OF CONNECTOR
C123527E02
CONNECT CONNECTOR

RS–82SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM
RS
DESCRIPTION
The front airbag sensor RH consists of the diagnostic circuit, the frontal deceleration sensor, etc.
If the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines
whether or not the SRS should be activated.
DTC B1610/13 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
WIRING DIAGRAM
DTC B1610/13 Front Airbag Sensor RH Circuit Malfunction
DTC No. DTC Detection Condition Trouble Area
B1610/13 When one of following conditions is met:
• Front airbag sensor RH malfunction
• Center airbag sensor malfunction• Engine room main wire
• Front airbag sensor RH
• Center airbag sensor
C123527E10