speed sensor TOYOTA SEQUOIA 2001 Service Repair Manual

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±609
803 Author: Date:
2005 SEQUOIA (RM1146U) Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
OFF malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle
8% or more
and 7.0% or more at 2,000 rpm
(Conditions vary with engine speed)
±
OFF malfunction (B)
Current ECM selected gear5th
Last ECM selected gear4th
Continuous time for ECM selecting 4th
gear2 sec. or more±
Actual gear when ECM selected 4th gear4th
OFF malfunction (C)
Current ECM selected gear5th
Last ECM selected gear4th
ON malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (B)
ECM selected gear4th
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (C)
ECM selected gear3rd
Vehicle speed2 km/h (1.2 mph) or more±

DI±614
± DIAGNOSTICSAUTOMATIC TRANSMISSION
808 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0756 Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0756The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve S2 remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve S2.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
RltdDTCP0756Shift solenoid valve S2/OFF malfunctionRelated DTCsP0756Shift solenoid valve S2/ON malfunction
MainShift solenoid valve S2
Required sensors/ComponentsSubVehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed
sensor (NO)
Frequency of operationContinuous
OFF malfunction (A), (B), (C)0.4 sec.
OFF malfunction (D)Immediate
DurationON malfunction (A) and (B)0.4 sec.Duration
ON malfunction (C)3 sec.
ON malfunction (D)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJD±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±615
809 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
OFF malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
OFF malfunction (B)
ECM selected gear2nd
Vehicle speed2 km/h (1.2 mph) or more±
Output speed2nd " 1st down shift point or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
OFF malfunction (C)
Current ECM selected gear5th
Last ECM selected gear4th
Continuous time for ECM selecting 4th
gear2 sec. or more±
Actual gear when ECM selected 4th gear4th
OFF malfunction (D)
Current ECM selected gear5th

DI±620
± DIAGNOSTICSAUTOMATIC TRANSMISSION
814 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0771 Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0771The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)

Shift solenoid valve SR remains open or closed

Shift solenoid valve SL1 remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve SR or SL1.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
Related DTCsP0771Shift solenoid valve SR/Rationality check
Rid /C tMainShift solenoid valve SRRequired sensors/ComponentsSubSpeed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operationContinuous
OFF malfunction (A)0.4 sec.
DurationOFF malfunction (B) and (C)ImmediateDuration
ON malfunction0.15 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
DIDJE±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±621
815 Author: Date:
2005 SEQUOIA (RM1146U) ETCS (Electric throttle control system)
Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
OFF malfunction (A)
ECM selected gear5th
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
OFF malfunction (B)
Current ECM selected gear5th
Last ECM selected gear4th
Continuous time for ECM selecting 4th
gear2 sec. or more±
OFF malfunction (C)
Current ECM selected gear5th
Last ECM selected gear4th
ON malfunction
Current ECM selected gear2th
Last ECM selected gear1st
Throttle valve opening angle
(During transition from 1st to 2nd gear)6.0% or more at 3,000 rpm
(Conditions vary with engine speed)±
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
[OFF malfunction]
All of the following conditions are met: OFF malfunctions (A), (B) and (C)
2 detections are necessary per driving cycle
1st detection; temporary flag ON
2nd detection; temporary pending fault code ON
OFF malfunction (A)
Turbine speed/Output speed0.93 to 1.07
OFF malfunction (B)
Turbine speed/Output speed
Not change as follow
0.93 to 1.07
O
0.65 to 0.79

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±625
819 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0776 Pressure Control Solenoid ºBº Performance
(Shift Solenoid Valve SL2)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0776The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)Shift solenoid valve SL2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve SL2.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
Related DTCsP0776Shift solenoid valve SL2/ON malfunction
Rid /C tMainShift solenoid valve SL2Required sensors/ComponentsSubSpeed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operationContinuous
ON malfunctions (A), (B) and
(C)0.4 sec.
DurationON malfunction (D)3 sec.
ON malfunction (E)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJF±01

DI±626
± DIAGNOSTICSAUTOMATIC TRANSMISSION
820 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
ON malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (B)
ECM selected gear3rd
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (C)
ECM selected gear4th
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (D)
Current ECM selected gear5th
Last ECM selected gear4th

D14169
1±2 Shift Valve
Valve Body:
DI±636
± DIAGNOSTICSAUTOMATIC TRANSMISSION
830 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0781 1±2 Shift (1±2 Shift Valve)
SYSTEM DESCRIPTION
The 1±2 shift valve performs shifting to 1st gear and other
gears.
DTC No.DTC Detection ConditionTrouble Area
P0781The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Valve body is blocked up or stuck (1±2 shift valve)

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates that the 1±2 shift valve in the valve body is locked in the direction the spring compresses.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº and switching oil pressure
to the valves in the valve body.
The ECM calculates the ºactualº transmission gear by comparing the signals from the input speed sensor
(NCO) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift sole-
noids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear
position and the commanded gear position are different, it will illuminate the MIL and store the DTC .
MONITOR STRATEGY
Related DTCsP0781Valve body/Rationality check
MainValve body
Required sensors/ComponentsSubAutomatic transmission assembly, Speed sensor (NT), Speed sensor
(NO), Vehicle speed sensor, Throttle speed sensor
Frequency of operationContinuous
Conditions (A) and (B)0.4 sec.
DurationCondition (C)3 sec.Duration
Condition (D)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJH±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±637
831 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
Condition (A)
ECM selected gear2nd
Vehicle speed2 km/h (1.2 mph) or more±
Output speed2nd " 1st down shift point or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
Condition (B)
ECM selected gear4th
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
Condition (C)
Current ECM selected gear5th
Last ECM selected gear4th
Vehicle speed
(During transition from 4th to 5th gear)±Less than 100 km/h (62.2 mph)
Condition (D)
ECM selected gear5th

D14171
Line Pressure
Control Pressure
Current Flow to Solenoid
D14172
ON
OFF
1 cycle
D14173
DI±656
± DIAGNOSTICSAUTOMATIC TRANSMISSION
850 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2714 Pressure Control Solenoid ºDº Performance
(Shift Solenoid Valve SLT)
SYSTEM DESCRIPTION
The linear solenoid valve (SLT) controls the transmission line
pressure for smooth transmission operation based on signals
from the throttle position sensor and the vehicle speed sensor.
The ECM adjusts the duty cycle of the SLT solenoid valve to
control hydraulic line pressure coming from the primary regula-
tor valve. Appropriate line pressure assures smooth shifting
with varying engine outputs.
(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle.
For example, if A is the period of continuity in one cycle, and B
is the period of non±continuity, then
Duty Ratio = A/(A + B) x 100 (%)
DTC No.DTC Detection ConditionTrouble Area
P2714
ECM detects a malfunction on SLT (ON side) according to the
revolution difference of the turbine and the output shaft, and
also by the oil pressure. (2±trip detection logic)
Shift solenoid valve SLT remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolu-
tion (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and outputs this DTC
when the amount of heat absorption exceeds the specified value.
When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force de-
creases.
NOTE: If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer
be drivable.
DIDJL±01