TOYOTA SEQUOIA 2001 Service Repair Manual

BE0G2±08
I18598
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±129
3533 Author: Date:
2005 SEQUOIA (RM1146U)
GARAGE DOOR OPENER SYSTEM
REGISTRATION PROCEDURE
1. NEW CODE REGISTRATION
NOTICE:

If pressing the switch of the original transmitter to
register the code, the system might operate.

When registering the transmitter codes such as for
garage or gate, check that there is nobody around
those places.
(a) Press the switch of the item to be registered for 20 se-
conds.
HINT:
When transferring to registration mode, garage door indicator
(green) blinks in 1 Hz cycle.
(b) Bring the original transmitter to within 1±inch area around
the garage door opener and press the switch (code trans-
mitting).
HINT:
When code registration is complete correctly, the garage door
indicator (green) blinks in 5.6 Hz cycle.

I03487
GARAGE DOOR
OPENER SWITCH
LEARN MODE
INDICATOR
OPERATION
ORIGINAL
TRANSMITTERPRESSED
ENTER
EXIT
ON
OFF20 sec.
INDICATOR flashes
at a rate of 1 Hz
INDICATOR
flashes at a
rate of 5.6 Hz RELEASED
ON
OFF BE±130
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3534 Author: Date:
2005 SEQUOIA (RM1146U)
New code registration timing chart
If a code can not be registered, observe the following condi-
tions.
HINT:

If the battery of original transmitter is consumed.

Press the switch of the transmitter repeatedly in registra-
tion mode, as some transmitters stop transmitting for 1 to
2 seconds.

This system is not applicable to the garage door opener
which had been made before 1982.
2. CODE DELETION
(a) Press the switches at both ends of the garage door open-
er simultaneously for 20 seconds.
HINT:
When transferring to deletion mode, garage door indicator
(green) blinks in 6 Hz cycle.
(b) When releasing the switch within 10 seconds after trans-
ferring to deletion mode, all the registered codes will be
erased.
HINT:
Press the switch until 6 Hz cycle blinking stops, so that the de-
fault code for check is set.

I21535
INDICATOR
OPERATION GARAGE DOOR
OPENER SWITCH
(Switch at either end)
ON
OFF ERASE/DEFAULT
MODEPRESSED
LOAD DEFAULT
INDICATOR flashes at a rate of 5.6 HZ 10 SEC.
20 SEC. RELEASED
ON
OFFEnter in erase mode to
erase all 3 channelsLOAD DEFAULT
NEW CODE REGISTRATION
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±131
3535 Author: Date:
2005 SEQUOIA (RM1146U)
Code deletion timing chart

BE0G3±10
I28422
Instrument Panel J/B

ECU±IG Fuse

GAUGE FuseOverhead Module

GAUGE Door Opener Switch
BE±132
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3536 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

BE0G4±01
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±133
3537 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT PERSONAL LIGHT LENS
2. REMOVE FRONT PERSONAL LIGHT
(a) Remove the 3 screws.
(b) Disconnect the 2 connectors.
3. REMOVE GARAGE DOOR OPENER SWITCH

I18597
BE26F±03
I18598
I18599
BE±134
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3538 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT GARAGE DOOR OPENER SWITCH
(a) Press the switch and check that each garage door indica-
tor (green) comes on.
(b) Even if only one switch does not come on, replace it.
2. INSPECT GARAGE DOOR OPENER REGISTRATION
AND TRANSMITTING
HINT:
Use the home link tester made by KENT MORE for this test.
As it is necessary to record the code of the hand held transmit-
ter, customer's code will be erased. When the inspection is
complete, please register the customer's again.
(a) Check that the inspection code of the hand held transmit-
ter can be recorded (See page BE±129).
If the code can not be registered, replace the garage door open-
er.
(b) Press the switch which an inspection code has been reg-
istered for and check that garage door indicator (green)
of the home link tester comes on.
If the garage door indicator (green) does not come on, replace
the garage door opener.

I21538
Wire Harness Side:
I21537
Wire Harness Side:
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±135
3539 Author: Date:
2005 SEQUOIA (RM1146U)
3. w/ Sliding Roof:
INSPECT GARAGE DOOR OPENER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 ± GroundAlwaysContinuity
3 ± GroundAlwaysBattery positive voltage
If the circuit is not as specified, inspect the power source or wire
harness.
4. w/o Sliding Roof:
INSPECT GARAGE DOOR OPENER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
9 ± GroundAlwaysBattery positive voltage
13 ± GroundAlwaysContinuity
If the circuit is not as specified, inspect the power source or wire
harness.

BE0G6±01
BE±136
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3540 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL GARAGE DOOR OPENER
2. INSTALL FRONT PERSONAL LIGHT
(a) Connect the 2 connectors.
(b) Install the 3 screws.
3. INSTALL FRONT PERSONAL LIGHT LENS

START
Insert the key in the key cylinder.
Under registration
Registration completion
Remove the key.
Will you register the
next key?
NoSecurity indicator blinks until the first
key is inserted. The indicator comes
on after the key registration.
Security Indicator
OFF
END Ye s
Security Indicator ON
(After the last key (sub±key) has been
registered, the indicator remains OFF
until the key is removed. After the key
is removed, the indicator blinks.)
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±137
3541 Author: Date:
2005 SEQUOIA (RM1146U)
ENGINE IMMOBILISER SYSTEM
REGISTRATION PROCEDURE
HINT:
If you lose all the registered master keys, you cannot registrar or delete additionally. Change the transponder
key ECU and then register the new key codes following the registration procedure of the automatic registra-
tion mode below.
1. KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE
(a) Registration of a new transponder key.
HINT:

This procedure must be done when you install a new transponder key ECU.

The new transponder key ECU is in automatic key code registration mode. The key codes already fixed
for this transponder key ECU can be registered.
For this type of vehicle, up to 3 key codes can be registered.

In the automatic registration mode, the last key registered becomes a sub±key.

1.8 Sec.
0.2 Sec.
0.25 Sec. 0.5 Sec.0.25 Sec.
1 Sec. Blinks
Code 2±1 Code 2±2
0.25 Sec.
0.25 Sec.0.5 Sec. 1 Sec. BE±138
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
3542 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

When a key cannot be inserted in the key cylinder in automatic registration mode, the security indicator
always comes on.

When the immobilizer system operates normally and the key is pull out, the security indicator blinks.

When key code registration could not be performed in automatic registration mode, code 2±1 is output
from the security indicator and when the registered key in inserted, code 2±2 is output.
(b) Automatic registration mode completion
If completing the mode forcibly when more than 1 key codes are registered in automatic registration
mode, perform the following procedures.
After 1 more key codes are registered with the master key, turn the ignition switch LOCK "ON 5 times
within 10 secs. by inserting the registered key or without pulling the key out.