sensor TOYOTA SEQUOIA 2001 Service Repair Manual

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±685
879 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2772 Transfer L4 SW Circuit
CIRCUIT DESCRIPTION
The ECM detects the signal from the transfer L4 position switch.
This DTC indicates that the transfer L4 position switch remains ON.
DTC No.DTC Detecting ConditionTrouble Area
P2772
Transfer L4 position switch remains ON while vehicle running
under conditions for 18 seconds or more (1±trip detection log-
ic)
(a) Output shaft speed 3000 rpm or less
(b) Transfer shift position is H
Short in transfer L4 position switch circuit

Transfer L4 position switch

4WD control ECU

ECM
MONITOR DESCRIPTION
The ECM monitors the transfer±case L4 position switch to determine when the transfer±case L4 gear is en-
gaged. If the transfer±case L4 gears remain engaged under the following conditions, the ECM will conclude
that there is a malfunction of the L4 position switch:

L4 switch indicated that the L4 transfer±case gears are engaged.

Transfer±case shifter is in the ºHº position.

Transfer±case output shaft rpm is between 750 and 3,000 rpm.

The specified time period has elapsed.
If all of the above conditions are detected, the ECM will conclude that there is a malfunction of the L4 switch,
and illuminate the MIL and store the DTC.
MONITOR STRATEGY
Related DTCsP2772Transfer L4 position switch/ON malfunction
Required sensors/ComponentsTransfer L4 position switch
Frequency of operationContinuous
DtiON malfunction (A)1.8 sec.DurationON malfunction (B)0.5 sec.
MIL operation1 driving cycle
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Output speed sensor circuitNot circuit malfunction
Vehicle speed sensor circuitNot circuit malfunction
Transfer neutral position switchOFF
ON malfunction (A)
Output speed (Transfer output speed)1,000 to 3,000 rpm
ON malfunction (B)
Output speed (Transfer output speed)143 rpm or more±
DIDJQ±01

DIDCF±01
F19439
Crankshaft
Position SensorEngine Room R/B No. 3
Engine Room J/B
Instrument
Panel J/B

STOP Fuse

IGN1 Fuse

ECU±IG Fuse
Stop Light
Switch
Combination Meter
Height Control Switch Body ECU
ECM Engine Room R/B No. 2
Suspension Control ECU
Translate ECU
4LO Switch
2WD/4HI Switch
Height Control Mode Select SwitchIgnition Switch
Height Control Indicator
Fusible Link Block

AIR SUS Fuse

AM2 Fuse

Height Control Manual IndicatorCenter Diff. Lock Switch
DLC3
Vehicle Speed Sensor
Vehicle Speed Sensor

AIR SUS Relay

AIR SUS No. 2 Fuse DI±696
± DIAGNOSTICSAIR SUSPENSION SYSTEM
890 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

F19440
Height Control
Cylinder Assy
(Pneumatic Cylinder)
Height Control Valve Height Control Cylinder Assy
(Pneumatic Cylinder)
Door Courtesy Light Switch

Leveling Solenoid Valve

Gate Solenoid ValveDoor Courtesy Light Switch

Compressor/Height Control Dryer

Exhaust Solenoid Valve

Height Control Cleaner
Height Control
Sensor Sub±assy
Compressor Assy
Back Door Courtesy
Light Switch
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±697
891 Author: Date:
2005 SEQUOIA (RM1146U)

DIDCI±01
F19438
Height Control Sensor
Sub±assy
Height Control Mode
Select Switch
Body ECU
Stop Light Switch
Front Door Courtesy
Light Switch (Driver)
Front Door Courtesy
Light Switch
(Passenger)
Rear Door Courtesy
Light Switch (LH)
Rear Door Courtesy
Light Switch (RH)
Back Door Courtesy
Light SwitchCombination Meter
Leveling Solenoid Valve
AIR SUS Relay
DLC3
ECM
Translate ECU Compressor/
Height Control Dryer
Exhaust Solenoid Valve Height Control Valve
Compressor Assy Gate Solenoid Valve IG
BBAT
SBL2
SHRL
SGL2VN
HI
NR
LO
TD
UPSW
DWSW
Door
STPSLRR
SLRL
RC
RM+
RM±
SLEX
SIL
CANH
CANL
CANSuspension
Control ECU Height Control Switch
GND From IG SwitchFrom Battery
From
Battery DI±698
± DIAGNOSTICSAIR SUSPENSION SYSTEM
892 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DIDCN±01
F19465
: CAN
Compressor Assy
Combination Meter
Suspension
Control
ECU Exhaust Solenoid
Valve
Gate Solenoid Valve
Leveling Solenoid ValveAIR SUS Relay
Height Control Cylinder
(Pneumatic Cylinder)
Height Control Sensor
Sub±assy : ECU Output Signal
: ECU Input Signal
: Air Flow Path
Dryer
Height Control Cylinder
(Pneumatic Cylinder)
Speed Sensors

Engine Speed

L4 Switch

Shift Position
Information

Transmission
Model Informa-
tion

Height Control Mode Select
Switch

Height Control Switch

Courtesy Light Switches

Stop Light SwitchHI
N
LO
MAN. DI±700
± DIAGNOSTICSAIR SUSPENSION SYSTEM
894 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. GENERAL
This system uses pneumatic cylinders instead of the coil springs that are used in a conventional rear
suspension. The suspension control ECU analyzes the information based on the switches, sensors,
and input signals, operates the compressor assy, and uses the solenoid valves to control the vehicle
height.
The suspension control ECU detects, via the height control sensor, the changes in the rear vehicle
height that results from the number of occupants or the amount of the load. Then, the suspension con-
trol ECU controls the height control solenoid valves and the compressor assy in order to automatically
adjust the rear vehicle height to a constant (normal) vehicle height.
Furthermore, three vehicle heights can be selected by operating the height control switch: HI, NOR-
MAL, and LO. The HI vehicle height ensures the vehicle's drive±through performance on rough roads.
The LO vehicle height facilitates the entry and exit of the occupants and the loading and unloading
of cargo. The NORMAL vehicle height helps realize excellent controllability and riding comfort during
normal driving.

DI±702
± DIAGNOSTICSAIR SUSPENSION SYSTEM
896 Author: Date:
2005 SEQUOIA (RM1146U)
3. FUNCTION OF MAIN COMPONENTS
ComponentOutline
Height Control Mode Select SwitchUsed to select vehicle height control mode (Auto/Manual).
Used to operate or stop auto leveling control.
Height Control SwitchAuto mode: Used to select vehicle height (HIGH, NORMAL, LOW).
Manual mode: Used to select vehicle height optionally.
Height Control SensorConverts the vertical change of the rear axle, in proportion to the standard, to sig-
nals and detects vehicle height.
Height Control Indicator Lamp (Combination Meter)Auto mode: Target vehicle height is displayed (HIGH, NORMAL, LOW).
Manual mode: Current vehicle height is displayed (HIGH, NORMAL, LOW).
Height Control Manual Indicator Lamp (Combination Meter)
Comes on during manual mode.
Blinks when the suspension control ECU detects a system malfunction.
Blinks during test mode.
Displays output DTC.
Stop light SwitchDetects braking condition.
Used to clear DTCs.
Pneumatic Cylinder (Height Control Cylinder Assy)Supports the vehicle body and adjusts the vehicle height.
Height Control Compressor Assy (Compressor/Height Con-
trol Dryer)The compressor generates compressed air that is necessary to raise vehicle
height and supplies it to the height control cylinder assy.
The dryer removes moisture from the compressed air.
Exhaust Solenoid ValveDrains the air in the height control cylinder assy when vehicle height is lowered.
(Built into the height control compressor assy)
Leveling Solenoid ValveOpens or closes the passage between the height cylinder assy and height control
compressor assy.
Gate Solenoid ValveOpens or closes the passage between the right and left height control cylinder assy
(Built into the leveling solenoid valve).
Suspension Control ECU
Estimates vehicle condition based on the signals from sensors and switches, and
outputs the control signals to the compressor and valves.
Blinks the height control manual indicator light when a system malfunction is de-
tected.
Air Suspension RelaySupplies power to the height control compressor assy.
Door Courtesy Switch (Body ECU)Detects whether the 5 doors, including the back door, are opened or closed, and
sends the signals to the suspension control ECU.
ECMSends the engine speed signal, etc. to the suspension control ECU through CAN
communication.
Speed Sensor (Skid Control ECU)Sends the vehicle wheel speed signal, etc. to the suspension control ECU through
CAN communication via the translate ECU.

F19470
Low
High
Link
Arm
DI±706
± DIAGNOSTICSAIR SUSPENSION SYSTEM
900 Author: Date:
2005 SEQUOIA (RM1146U)
Height Control Sensor
The height control sensor detects the vehicle height. One sensor is located in the center of the rear
frame, which is connected to the center of the rear axle via a link, in order to detect the vehicle height.
The sensor has an arm that moves along with the change in vehicle height, and the resultant change
in voltage enables the suspension control ECU to detect the vehicle height.
A semiconductor type sensor has been adopted to make it compact and heat±resistant.
HINT:
Refer to the following factors when adjusting the link of the height control sensor:
The vehicle height changes approximately 4 mm (0.16 in.) with each turn of the link.
The vehicle height changes approximately 2 mm (0.08 in.) by moving the link installation position by
1 mm (0.04 in.).

F16802
0.25 sec. 0.5 sec.
ON
OFF
0.25 sec.4.5 sec.
ON
OFF1.5 sec. Normal:
Code 82:
0.5 sec.
Repeat
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±713
907 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

As examples, the blinking patterns of a normal system
code and code 82 are shown in the illustration.

If 2 or more malfunctions are indicated at the same time,
the lowest numbered code is displayed first.

When a DTC is not output, check the TC terminal circuit
on page DI±1567.
(9) Check the malfunction using the code table on the
next page.
(b) Ending the Input Signal Check Mode (Test Mode) using
SST check wire.
SST 09843±18040
(1) With the ignition switch OFF, disconnect the SST
check wire from the terminals of the DLC3 and then
turn the ignition switch to the ON position.
(c) Procedure for Sensor Test Mode (Test Mode) using the
hand±held tester.
(1) Make sure the ignition switch is OFF.
(2) Set each of the check items to the condition shown
under Operation (A) in the test mode table on the
previous page.
(3) Connect the hand±held tester to the DLC3.
(4) Turn the ignition switch to the ON position.
(5) Select SIGNAL CHECK mode on the hand±held
tester.
(6) Set each of the check items to the condition shown
under Operation (B) in the test mode table on the
previous page.
HINT:
In step (6), all signals can be checked together.
(7) Read the DTCs by following the prompts on the tes-
ter screen.
HINT:
Refer to the hand±held tester operator's manual for further de-
tails.

DIDCZ±01
DI±716
± DIAGNOSTICSAIR SUSPENSION SYSTEM
910 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:

If a normal system code is displayed during the DTC check but the problem still occurs, check the cir-
cuits for each problem symptom in the order given in the table below and proceed to the relevant trou-
bleshooting page.

Inspect the fuse before inspecting the suspected areas as shown in the chart below.

Inspect each malfunction circuit in numerical order for the corresponding symptom.

If the malfunction still exists even after checking and confirming that all the circuits are normal, replace
the suspension control ECU.
SymptomSuspected AreaSee page
Vehicle height control function does not operate.
If the compressor remains on for an excessive period of
time or turns on and off repeatedly, the system control will
be halted for up to 70 minutes, after which the system will
return to normal operation.
1. Air tube is seized
2. Power source circuit
3. IG signal circuit
4. Crankshaft position sensor circuit
5. Height control mode select switch circuit
6. Height control switch circuit
7. Height control sensor circuit
8. Leveling solenoid valve circuit
9. Gate solenoid valve circuit
10.Exhaust solenoid valve circuit
11. AIR SUS relay circuit
12.Height control compressor circuit
13.Suspension control ECU
±
DI±761
DI±793
DI±210
DI±778
DI±774
DI±731
DI±740
DI±736
DI±744
DI±747
DI±752
IN±35
Illuminated position of height control indicator lamp does not
change by the height control switch operation.
1. Power source circuit
2. Crankshaft position sensor circuit
3. Height control mode select switch circuit
4. Height control switch circuit
5. Height control sensor circuit
6. Leveling solenoid valve circuit
7. Gate solenoid valve circuit
8. Exhaust solenoid valve circuit
9. AIR SUS relay circuit
10.Height control compressor circuit
11. Speed sensor circuit
12.CAN communication circuit
13.Suspension control ECUDI±763
DI±761
DI±793
DI±210
DI±778
DI±774
DI±731
DI±740
DI±736
DI±744
DI±783
DI±1065
IN±35
Hunting of vehicle height occurs.
1. Air leakage (Height control cylinder assy rear)
2. Height control sensor circuit
3. Suspension control ECUSA±156
DI±731
IN±35
Vehicle height control operates, but vehicle height is uneven.
1. Air leakage
2. Clogging of the air tube
3. Height control sensor link sub±assy
4. Height control sensor circuit
5. Gate solenoid valve circuit
6. Suspension control ECUSA±156
±
SA±156
DI±731
DI±736
IN±35
Vehicle height control operates, but vehicle height is high or
low (Vehicle height in NORMAL mode differs from the standard
value).1. Height control sensor link sub±assy
2. Height control sensor circuit
3. Suspension control ECUSA±156
DI±731
IN±35
When vehicle height control is adjusted, it stops at extremely high
or low position.1. Height control sensor circuit
2. Height control sensor link sub±assy
3. Suspension control ECUDI±731
SA±156
IN±35

± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±717
911 Author: Date:
2005 SEQUOIA (RM1146U) Height control manual indicator lamp condition is abnormal.
1. Power source circuit
2. Height control mode select switch circuit
3. Height control manual indicator lamp circuit
4. Suspension control ECUDI±763
DI±778
DI±789
IN±35
Height control indicator lamp condition is abnormal.
1. Power source circuit
2. Height control indicator lamp circuit
3. Suspension control ECUDI±763
DI±785
IN±35
DTC check cannot be completed.
1. Power source circuit
2. CAN communication system
3. Height control manual indicator lamp circuit
4. Suspension control ECU
5. ECMDI±763
DI±782
DI±789
IN±35
IN±35
Input signal check (test mode) cannot be completed.
1. Power source circuit
2. CAN communication system
3. Suspension control ECU
4. Translate ECUDI±763
DI±783
IN±35
IN±35
Vehicle height is extremely low when vehicle is parked.
Although, especially in a cold district, the vehicle height
may become lower due to a drop in air temperature in the
height control cylinder assy, but this is not abnormal.
1. Air leakage
2. Height control cylinder assy
3. Height control sensor link sub±assy
4. Leveling solenoid valve circuit
5. Exhaust valve circuit
SA±156
±
SA±156
DI±740
DI±744
Compressor motor continues to operate.
Due to the air tube freezing, vehicle height may not rise.
1. Air leakage
2. Air tube clogged
3. Height control cylinder assy
4. Height control sensor link sub±assy
5. Height control sensor circuit
6. Leveling solenoid valve circuit
7. Exhaust valve circuit
8. AIR SUS relay circuit
9. Height control compressor circuit
10.Suspension control ECU
SA±156
±
±
SA±156
DI±731
DI±740
DI±744
DI±747
DI±752
IN±35