navigation TOYOTA SIENNA 2007 Service Owner's Manual

PARK ASSIST / MONITORING – REAR VIEW MONITOR SYSTEMPM–3
PM
SYSTEM DESCRIPTION
1. GENERAL
(a) To assist the driver with parking the vehicle by
displaying an image of the area behind the vehicle,
this system has a television camera mounted on the
luggage compartment door. The system displays
the image on the radio and navigation assembly.
(b) This system consists of the following components:
(1) Radio and navigation assembly
(2) Television camera assembly
(c) This system is equipped with a self-diagnosis
system, which is operated on a dedicated window
that appears on the display panel, just as in the
navigation system.
2. FUNCTION OF COMPONENTS
(a) The radio and navigation assembly controls the
system by using information from the following
components:
3. OPERATION EXPLANATION
(a) The radio and navigation assembly receives the R
position signal from the park / neutral position switch
when the shift lever is moved to the R position. After
receiving the R position signal, the radio and
navigation assembly switches from the navigation
system to the rear view monitor system.
4. NOTES FOR REAR VIEW MONITOR
(a) Notes for the rear view monitor.
(1) The rear view monitor may not function properly
if subjected to a severe blow by any hard object.
(2) Do not "scrub" the cover part of the camera
(resin made). Scrubbing it may scratch the cover
and affect the image. Prevent organic solvents,
waxes, bond removing solvents, or glass coating
from adhering to the cover. Clean it off
immediately, and wash with water.
(3) Exposing the camera to a sudden temperature
change may affect proper functioning of the
camera.
(4) A clear image may not appear if the camera is
dirty with snow, mud, etc. In that case, wash it
with water and wipe off the lens. Use a detergent
to remove dirt if necessary.
Item Function
Television Camera Assembly• Mounted on the luggage compartment door to transmit the rear
view of the vehicle to the radio and navigation assembly.
• A color video camera that uses a CCD (Charge Coupled Device)
and a wide-angle lens.
Radio and Navigation Assembly• Transmits video signals, which contain an image of the area
behind the vehicle taken with the television camera assembly.
• Radio and navigation assembly effects control of the system by
receiving the shift position signal from park/neutral position switch.
• Displays the rear view monitor image on the display panel.
Park/Neutral Position SwitchTransmits a reverse shift position signal to the radio and navigation
assembly.

AIR CONDITIONING – INTEGRATION CONTROL AND PANELAC–255
AC
REMOVAL
1. REMOVE INSTRUMENT CLUSTER FINISH PANEL
CENTER NO.1 (See page IP-8)
2. REMOVE INSTRUMENT CLUSTER FINISH PANEL
CENTER NO.2
3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
HINT:
(See page AX-146 for U151E, AX-146 for U151F)
4. REMOVE INSTRUMENT CLUSTER FINISH PANEL
ASSEMBLY CENTER (See page IP-9)
5. REMOVE INSTRUMENT CLUSTER FINISH PANEL
GARNISH (See page IP-9)
6. REMOVE RADIO RECEIVER ASSEMBLY WITH
BRACKET (w/o Navigation System) (See page AV-
169)
7. REMOVE RADIO RECEIVER ASSEMBLY WITH
BRACKET (w/ Navigation System)
8. REMOVE INTEGRATION CONTROL AND PANEL
ASSEMBLY
(a) Remove the 4 screws, and release the integration
control & panel assembly.
(b) Disconnect the connectors and remove the
integration control & panel assembly.
DISASSEMBLY
1. REMOVE CENTER CLUSTER MODULE KNOB NO.1
(for Manual Air Conditioning System)
(a) Remove the center cluster module knob No. 1.
2. REMOVE CENTER CLUSTER MODULE KNOB NO.2
(for Manual Air Conditioning System)
(a) Release the 2 claws fittings and remove the center
cluster module knob No. 2.
NOTICE:
Take care not to break the claws on the knob.
I035724
I035725
I035726E01

AC–260AIR CONDITIONING – INTEGRATION CONTROL AND PANEL
AC
INSTALLATION
1. INSTALL INTEGRATION CONTROL AND PANEL
ASSEMBLY
2. INSTALL RADIO RECEIVER WITH BRACKET (w/
Navigation System)
3. INSTALL RADIO RECEIVER WITH BRACKET (w/o
Navigation System)
4. INSTALL INSTRUMENT CLUSTER FINISH PANEL
GARNISH
5. INSTALL INSTRUMENT CLUSTER FINISH PANEL
ASSEMBLY CENTER
6. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
7. INSTALL INSTRUMENT CLUSTER FINISH PANEL
CENTER NO.2
8. INSTALL INSTRUMENT CLUSTER FINISH PANEL
CENTER NO.1

AIR CONDITIONING – INTEGRATION CONTROL AND PANELAC–255
AC
REMOVAL
1. REMOVE INSTRUMENT CLUSTER FINISH PANEL
CENTER NO.1 (See page IP-8)
2. REMOVE INSTRUMENT CLUSTER FINISH PANEL
CENTER NO.2
3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
HINT:
(See page AX-146 for U151E, AX-146 for U151F)
4. REMOVE INSTRUMENT CLUSTER FINISH PANEL
ASSEMBLY CENTER (See page IP-9)
5. REMOVE INSTRUMENT CLUSTER FINISH PANEL
GARNISH (See page IP-9)
6. REMOVE RADIO RECEIVER ASSEMBLY WITH
BRACKET (w/o Navigation System) (See page AV-
169)
7. REMOVE RADIO RECEIVER ASSEMBLY WITH
BRACKET (w/ Navigation System)
8. REMOVE INTEGRATION CONTROL AND PANEL
ASSEMBLY
(a) Remove the 4 screws, and release the integration
control & panel assembly.
(b) Disconnect the connectors and remove the
integration control & panel assembly.
DISASSEMBLY
1. REMOVE CENTER CLUSTER MODULE KNOB NO.1
(for Manual Air Conditioning System)
(a) Remove the center cluster module knob No. 1.
2. REMOVE CENTER CLUSTER MODULE KNOB NO.2
(for Manual Air Conditioning System)
(a) Release the 2 claws fittings and remove the center
cluster module knob No. 2.
NOTICE:
Take care not to break the claws on the knob.
I035724
I035725
I035726E01