glove box TOYOTA SIENNA 2007 Service Repair Manual

INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PADIP–7
IP
18. REMOVE GLOVE COMPARTMENT DOOR STOPPER
SUB-ASSEMBLY
(a) Disengage the claw, and remove the glove
compartment door stopper sub-assembly.
19. REMOVE GLOVE COMPARTMENT DOOR
ASSEMBLY
(a) Push the right side wall and then push the left wall
to release the stoppers.
(b) Pull the glove compartment door sub-assembly
rearward to remove it.
20. REMOVE INSTRUMENT PANEL BOX NO.2
(a) Disengage the 2 claws and the 4 clips, and remove
the instrument panel box No. 2.
21. REMOVE INSTRUMENT SIDE PANEL LH
(a) Disengage the 5 claws by pulling up the edge of the
instrument side panel LH from the rear of the
vehicle.
(b) Remove the instrument side panel LH.
22. REMOVE INSTRUMENT SIDE PANEL RH
B066072
B066073E01
B066074
B066075E01
B066076E01

ES–4982GR-FE ENGINE CONTROL SYSTEM – ECM
ES
REMOVAL
1. REMOVE GLOVE COMPARTMENT DOOR
ASSEMBLY
(a) Push the right side wall and then push the left wall
to release the stoppers.
(b) Pull the glove compartment door sub-assembly
rearward to remove it.
2. REMOVE NO. 2 INSTRUMENT PANEL BOX
(a) Disengage the 2 claws and 4 clips, and remove the
No. 2 instrument panel box.
3. REMOVE ECM
(a) Disconnect the 5 ECM connectors.
(b) Remove the 2 nuts and ECM.
B066073E01
B066074
B066075E01
A162672

ES–5002GR-FE ENGINE CONTROL SYSTEM – ECM
ES
2. INSTALL ECM (with 10 speakers system)
(a) Install the ECM and stereo components amplifier
with the 4 nuts.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
(b) Connect the 5 ECM connectors and 2 stereo
components amplifier connectors.
3. INSTALL NO. 2 INSTRUMENT PANEL BOX
(a) Install the No. 2 instrument panel box.
4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
(a) Install the glove compartment door sub-assembly
frontward to install it.
(b) Push the right side wall and then push the left wall
to install the stoppers.
5. PERFORM REGISTRATION
(a) When replacing the ECM, perform distance control
ECU recognition in ECM (See page CC-125).
A162676
B066075E01
A162677
B066073E01

AC–100AIR CONDITIONING – AIR CONDITIONING SYSTEM (for Automatic Air Conditioning Sys-
tem)
AC
(c) Select the items below in the DATA LIST, and read the
display on the intelligent tester.
DATA LIST / AIR CONDITIONER
OK:
When the target position is "RECIRCULATION" (-
10%), the actual opening angle is 19.0% or less.
When the target position is "FRESH" (110%), the
actual opening angle is 81.0% or more.
Result
B
C
A
(a) Remove the glove box to see and check the recirculation
damper operation.
(b) Connect the intelligent tester to the DLC3.
(c) Turn the ignition switch to the ON position and turn the
intelligent tester main switch on.
(d) Select the item below in the ACTIVE TEST and then
check that the damper operates.
ACTIVE TEST / AIR CONDITIONER
OK:
Lever turns from "RECIRCULATION" side to
"FRESH" side smoothly.
Lever turns from "FRESH" side to
"RECIRCULATION" side smoothly.
Result
B
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/I DAMP POSAir inlet damper position / min.: -
14%, max.: 113.5%Damper is at
"RECIRCULATION": -10%
Damper is at "HALF-
RECIRCULATION": 35 to 75%
Damper is at "FRESH": 110%Open in the circuit: 50.0%
A/I DAMP TARGAir inlet damper target position /
min.: -14%, max.: 113.5%
Result Proceed to
NGA
OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE) B
OK (When troubleshooting according to the DTC) C
PROCEED TO NEXT CIRCUIT INSPECTION
SHOWN IN PROBLEM SYMPTOMS TABLE
REPLACE A/C AMPLIFIER
2PERFORM ACTIVE TEST BY INTELLIGENT TESTER
Tester Display Test Part Control Range Diagnostic Note
A/I DAMP-LINEAR Air inlet damper position (linear) min.: -14%, max.: 113.5% -
Result Proceed to
NGA
OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE) B
OK (When troubleshooting according to the DTC) C
PROCEED TO NEXT CIRCUIT INSPECTION
SHOWN IN PROBLEM SYMPTOMS TABLE

AIR CONDITIONING – AIR CONDITIONING SYSTEM (for Automatic Air Conditioning Sys-
tem)AC–101
AC
C
A
(a) Remove the glove box to see and check the recirculation
damper operation.
(b) Enter the actuator check mode (See page AC-15).
(c) Press the DEF switch and check the operation of the
recirculation damper.
OK:
Recirculation damper position changes in
accordance with each display code.
Result
B
C
AREPLACE A/C AMPLIFIER
3PERFORM ACTUATOR CHECK
Display Code Recirculation Damper Position
0FRESH (110%)
1FRESH (110%)
2FRESH (110%)
3 R/F (50%)
4 RECIRCULATION (-10%)
5 RECIRCULATION (-10%)
6 RECIRCULATION (-10%)
7 RECIRCULATION (-10%)
8 RECIRCULATION (-10%)
9 RECIRCULATION (-10%)
Result Proceed to
NGA
OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE) B
OK (When troubleshooting according to the DTC) C
PROCEED TO NEXT CIRCUIT INSPECTION
SHOWN IN PROBLEM SYMPTOMS TABLE
REPLACE A/C AMPLIFIER