ECU TOYOTA SOLARA 2007 (in English) Service Manual

189
The system may not function in the follow-
ing conditions and places:
The cellular phone is turned off.
The current position is outside the
communication area.
The cellular phone is not connected.
The cellular phone has a low battery.
The cellular phone is located behind
the seat or in the glove box and con-
sole box.
The cellular phone touches or is cov-
ered with metal materials.
This system supports the following ser-
vice.
HFP (Hands Free Profile) Ver.1.0
DNP (Dial −up Networking Profile)
Ve r. 1 . 1
OPP (Object Push Profile) Ver.1.1
If your cellular phone does not support
HFP, you cannot enter the Bluetooth 
phone, and take OPP service individually.
BLUETOOTH is a trademark owned by
Bluetooth SIG. Inc. When transferring ownership of the ve-
hicle:
A lot of personal data is registered
when you use the handsfree system.
When transferring ownership of the ve-
hicle, initialize the system.
If you initialize it, the former state will
never come back again. Pay much atten-
tion when initializing the data.
You can initialize the following data in the
system.
Phone book data
Dialed numbers and received calls
Speed dial
Bluetooth
 phone data
Security code
FCC ID: HYQBTAU01A
IC ID: 1551ABTAU01A
MADE IN JAPAN
This device complies with Part 15 of the
FCC Rules and RSS −210. Operation is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) This device must
accept any interference received, includ-
ing interference that may cause unde-
sired operation.
CAUTION
Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user’s authority to operate the equip-
ment.

194
Set PassKey
The passkey can be c hanged. A 4 to 8
digit code can be input as a pa sskey.
Delete
The registered phones can be deleted.
To enter the phone setup menu 1. Push the off −hook switch to turn the
hands −free system on.
2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Setup] is displayed and push the knob.
[Setup. Please push the talk switch and
say security, or phone setup.] is heard.
3. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Phone Setup] is displayed and push
the knob.
[Phone setup. Push the talk switch and
say pair phone, select phone, change
name, list phones, set pa sskey or delete.]
is heard.
[XXX (phone name) already selected.] is
heard and the phone name is displayed.
If no phone has been registered, the sys-
tem may not function properly. To pair phones
1. Push the talk switch and say [Pair phone], or turn the “AUDIO CONTROL”
knob until [Pair Phone] is displayed
and push the knob.
[Pair. Push the talk switch and say a
name for the phone.] is heard. 2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Record Name] is displayed, push the
knob and say the desired phone name.
[Push the talk switch and say confirm.
Otherwise, say go back.] is heard. 3. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Confirm] is displayed and push the
knob.
[XXX (desired phone name) Ready for
phone pairing. Please use the phone to
connect it to the hands −free system. The
passkey for the p hone is....] is heard.
After “HANDS FREE” is displayed, a pass-
key
∗ is displayed and [Searching.] is
heard.
4. Input the displayed passkey into the phone. [The phone is paired and ready for use.
Returning to the main menu.] is heard and
[Paired] is displayed.
The system may not function in the follow-
ing cases:
If 6 phones have already been regis-
tered.
If the vehicle is moving.
If the system cannot communicate with
the phone.
∗: Passkey is a password r
equired to reg-
ister a phone to the system.
INFORMATION
To use the handsfree system, you
need to register your phone in the
system. Once you have registered
it, you can make a handsfree call.
Up to 6 phones can be registered.
For the operation of the phone, see
the manual that comes with your
cellular phone.
The passkey can be changed. See
page 197 for changing the passkey.

198
To delete a phone1. Push the talk switch and say [Delete], or turn the “AUDIO CONTROL” knob
until [Delete] is displayed and push the
knob.
[Delete. Push the talk switch and say the
phone name to delete.] is heard. 2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
the phone name you want to delete is
displayed and push the knob.
When using a voice command:
[XXX (desired phone name) Push the talk
switch and say confirm. Otherwise, say go
back.] is heard and the phone name is
displayed.
Follow voice guidance instructions, or turn
the “AUDIO CONTROL” knob until [Con-
firm] is displayed and push the knob.
[Deleted. Returning to the phone setup.] is
heard and $ [Deleted]$ is displayed.
When using the knob:
[Deleted. Returning to the phone setup.] is
heard and [Deleted] is displayed. The system may not function in the follow-
ing cases:
If no phone has been registered.
If the system does not recognize the
voice command.
The security menu includes the following:
Set PIN (Personal Identification Num-
ber)
The PIN can be set or changed.
Phone book lock
The phone book can be locked.
When the phone book is locked, the fol-
lowing functions cannot be used:
Dial by name
Redial
Callback
Speed Dial
PhoneBook
Phone book unlock
The locked phone book can be unlocked.
—Security

199
To enter the security menu1. Push the off −hook switch to turn the
hands −free system on.
2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Setup] is displayed and push the knob.
[Setup. Please push the talk switch and
say security, or phone setup.] is heard.
3. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Security] is displayed and push the
knob.
[Security. Push the talk switch and say
set PIN, phone book lock, or phone book
unlock.] is heard. To set a PIN
Push the talk switch and say [Set PIN],
or turn the “AUDIO CONTROL” knob until
[Set PIN] is displayed and push the knob.
[There is no PIN number set. Please reg-
ister a PIN number. Please push the talk
switch and say a four
−digit PIN number.]
is heard. When using a voice command:
1. Push the talk switch and say a new PIN number.
2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Confirm] is displayed and push the
knob.
[The PIN number has been set. Returning
to the security.] is heard and [Completed]
is displayed.
When using the knob: 1. Turn the “AUDIO CONTROL” knob to select a number. Push the “AUDIO
CONTROL” knob to set.
2. Repeat the above procedure until the entire four −digit number is set.
3. When the PIN is set, push the “AUDIO CONTROL” knob.
4. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Confirm] is displayed and push the
knob.
[The PIN number has been set. Returning
to the security.] is heard and [Completed]
is displayed.

200
If the PIN is to be changed:
[There is a PIN number in place. Push the
talk switch and say the correct PIN num-
ber.] is heard and [Current PIN?] is dis-
played.1. Follow voice guidance instructions, or use the “AUDIO CONTROL” knob to
input the current PIN number.
[Please push the talk switch and say a
four −digit PIN number.] is heard.
2. Push the talk switch and say new PIN number.
[The PIN number has been set. Returning
to the security.] is heard and [Completed]
is displayed.
If the current number is not correct, the
system does not function properly. To lock the phone book
1. Push the talk switch and say [Phone book lock], or turn the “AUDIO CON-
TROL” knob until [Phbk Lock] is dis-
played and push the knob.
[There is a PIN number in place. Push the
talk switch and say the correct PIN num-
ber.] is heard and [Current PIN?] is dis-
played. 2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob to
select a number. When using a voice command:
[XXXX (PIN number) Push the talk switch
and say confirm. Otherwise, say go back.]
is heard and PIN number is displayed.
Follow voice guidance instructions, or turn
the “AUDIO CONTROL” knob until
[Confirm] is displayed and push the knob.
[PIN number accepted. The phone book is
now locked. Returning to the main menu.]
is heard and [Locked] is displayed.
When using the knob:
1. Turn the “AUDIO CONTROL” knob to select a number. Push the “AUDIO
CONTROL” knob to set.
2. When the PIN number is set, push the “AUDIO CONTROL” knob.
[XXXX Push the talk switch and say con-
firm. Otherwise, say go back.] is heard
and PIN number is displayed. 3. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
[Confirm] is displayed and push the
knob.
[PIN number accepted. The phone book is
now locked. Returning to the main menu.]
is heard and [Locked] is displayed.

243
Perform circling calibration just after
you have purchased your Toyota. And
then always perform circling calibration
after the battery has been removed, re-
placed or disconnected.
Do not perform circling calibration of
the compass in a place where the
earth’s magnetic field is subject to in-
terference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).
During calibration, do not operate elec-
tric systems (moon roof, power win-
dows, etc.) as they may interfere with
the calibration.
CAUTION
When doing the circling calibration,
be sure to secure a wide space,
and watch out for people and ve-
hicles in the neighborhood. Do not
violate any local traffic rules while
performing circling calibration.
Do not adjust the display while the
vehicle is moving. Be sure to adjust
the display only when the vehicle is
stopped.
The ashtray can be removed and used
outside the vehicle. To use the ashtray,
raise the lid.
When finished with your cigarette, thor-
oughly extinguish it in the ashtray to pre-
vent other cigarette butts from catching
fire. After using the ashtray, close the lid
completely.
The cup holder lid cannot be closed while
the ashtray is installed.
To detach the ashtray, pull it out.
Portable ashtray

245
Indicator lightButtons
Coupe
Indicator light
Buttons
Convertible
The garage door opener (
Universal Transceiver) is manufactured
under license from HomeLink and can
be programmed to operate garage
doors, gates, entry doors, door locks,
home lighting systems, and security
systems, etc.
(a) Programming the HomeLink

The HomeLink in your vehicle has 3
buttons and you can store one program
for each button.
To ensure correct programming into the
HomeLink
, install a new battery in the
hand− held transmitter prior to program-
ming.
The battery side of the hand −held trans-
mitter must be pointed away from the
HomeLink
 during the programming pro-
cess.
For Canadian users, follow the procedure
in “Programming an entrance gate/pro-
gramming all devices in the Canadian
market”.
1. Decide which of 3 HomeLink
 buttons
you want to program.
HomeLink 
Hand −held
garage
transmitter
25 to
75 mm
(1 to 3 in.)
Coupe
HomeLink 
Hand −held
garage
transmitter
25 to
75 mm
(1 to 3 in.)
Convertible
Garage door opener

248
The ceiling mounted garage door opener
motor should now recognize the
HomeLink
 unit and be able activate the
garage door up/down.
4. Repeat steps 1 through 3 for each re- maining HomeLink
 button to program
another rolling code system.
Programming an entrance gate/program-
ming all devices in the Canadian market 1. Decide which of the 3 HomeLink
 but-
tons you want to program.
2. Place your hand− held gate/device
transmitter 25 to 75 mm (1 to 3 in.)
away from the surface of the
HomeLink
.
Keep the indicator light on the HomeLink

in view while programming.
3. Press and hold the selected HomeLink
 button.
4. Continuously press and release ( cycle)
the hand− held gate/device transmitter
button every two seconds until step 5
is complete.
5. When the indicator light on the HomeLink
 changes from a slow to a
rapid flash after 20 seconds, you can
release both buttons. 6. Test the operation of the HomeLink
 by
pressing the newly programmed button.
Check to see if the gate/device oper-
ates correctly.
7. Repeat steps 1 through 6 for each re- maining HomeLink
 button to program
another device.
Programming other devices
To program other devices such as home
security systems, home door locks or
lighting, contact your authorized Toyota
dealer for assistance.
Reprogramming a button
Individual HomeLink
 buttons cannot be
erased, however, to reprogram a single
button, follow the procedure “Programming
the HomeLink
”.
(b) Operating the HomeLink

To operate the HomeLink, press the
appropriate HomeLink button to activate
the programmed device. The HomeLink
indicator light should come on. The
HomeLink continues to send the signal
for up to 20 seconds as long as the
button is pressed.
Coupe
Convertible

252
CONSOLE BOX
To access the rear console box, pull up
the lock release lever while raising the
rear console box lid.
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the console box closed
while driving.
Front
Rear
The cup holder is designed for holding
cups or drinkcans securely.
Front cup holder—
To use the front cup holder, open the lid.
A cup holder adapter is located among the
cup holders which are under the lid. To
hold the cups or drink−cans securely, ad-
just the size with the adapter.
CAUTION
Do not place anything else other
than cups or drinkcans in the cup
holder, as such items may be
thrown about in the compartment
and possibly injure people in the
vehicle during sudden braking or in
an accident.
To reduce the chance of injury in
case of an accident or sudden stop
while driving, keep the front cup
holder closed when it is not in use.
Cup holders

253
This box is designed to hold things like
bottles.This hook is designed to hang things
like grocery bags.
NOTICE
To prevent damage to the hook, avoid
hanging heavy loads on it.
To secure belongings, hang the cargo
net on the hooks.
NOTICE
Do not use the net to secure sharp
or heavy objects. The net will tear
off.
 Be sure not to twist the net when
hooking.
Storage box Grocery bag hooksCargo net