relay TOYOTA SUPRA 1997 Service Owners Manual

F02629F02645F02646
LOCK
A8
W02801
ABS Solenoid
Relay
ABS
Actuator
ECUA8
A6A6
A6A6
A193
9
22
2
DI-462
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
690 Author
: Date
:
1997 SUPRA (RM502U)
INSPECTION PROCEDURE (2JZ-GE Engine)
1 Check voltage between terminal A8 - 1 of ABS control (motor) relay connector
and body ground.
PREPARATION:
Disconnect the ABS control (motor) relay connector.
CHECK:
Measure voltage between terminal A8 - 1 of ABS control (mo-
tor) relay connector and body ground.
OK:
Voltage: 10 - 14 V
NG Check and repair harness or connector.
OK
2 Check continuity between terminal A8 - 2 of ABS control (motor) relay connector
and terminal A19 - 9 of ABS ECU.
CHECK:
Check continuity between terminal A8 - 2 of ABS control (mo-
tor) relay connector and terminal A19 - 9 of ABS ECU.
OK:
Continuity
HINT:
There is a resistance of 26 ~ 40 W between terminals A6 - 2 and
A6 - 3 of ABS actuator.
NG Repair or replace harness or ABS actuator.
OK

F02648
Open
Continuity
Continuity
A8 A8
A9
A9
1
3
42
1
3
42
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-463
691 Author
: Date
:
1997 SUPRA (RM502U)
3 Check ABS control (motor) relay.
CHECK:
Check continuity between each terminal of ABS control (motor)
relay.
OK:
Terminals A8 - 3 and A8 - 4Continuity (Reference value 62 W)
Terminals A8 - 1 and A8 - 2Open
CHECK:
(a) Apply battery voltage between terminals A8 - 3 and A8
- 4.
(b) Check continuity between terminals of ABS control (mo-
tor) relay.
OK:
Terminals A8 - 1 and A8 - 2Continuity
NG Replace ABS control relay.
OK
4 Check for open and short in harness and connector between ABS motor relay
and ABS ECU (See page IN-28).
NG Repair or replace harness or connector.
OK
If the same code is still output after the DTC is deleted, check the contact condition of each con-
nection.
If the connections are normal, the ECU may be defective.

F02629F02649F02650
LOCK
R/B No.5
(+) (-)
F03315
ABS Solenoid
Relay
ABS
Actuator
ECUA6
A6
A6A6
A21
2
22
3
10
DI-464
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
692 Author
: Date
:
1997 SUPRA (RM502U)
INSPECTION PROCEDURE (2JZ-GTE Engine)
1 Check voltage between terminal 1 of R/B No.5 (for ABS motor relay) and body
ground.
PREPARATION:
Remove ABS motor relay from R/B No.5.
CHECK:
Measure voltage between terminal 1 of R/B No.5 (for ABS mo-
tor relay) and body ground.
OK:
Voltage: 10 - 14 V
NG Check and repair harness or connector.
OK
2 Check continuity between terminal 2 of R/B No.5 (for ABS motor relay) and termi-
nal A21 - 10 of ABS ECU.
CHECK:
Check continuity between terminal 2 of R/B No.5 (for ABS mo-
tor relay) and terminal A21 - 10 of ABS ECU.
OK:
Continuity
HINT:
There is a resistance of 26 ~ 40 W between terminals A6 - 2 and
A6 - 3 of ABS actuator.
NG Repair or replace harness or ABS actuator.
OK

F03316F03317F03318F03319
1 2
3 4
Open
Continuity
Continuity
(-)
(+)
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-465
693 Author
: Date
:
1997 SUPRA (RM502U)
3 Check ABS motor relay.
PREPARATION:
Remove motor relay from R/B No.5.
CHECK:
Check continuity between each terminal of motor relay.
OK:
Terminals 3 and 4Continuity (Reference value 62 W)
Terminals 1 and 2Open
CHECK:
(a) Apply battery voltage between terminals 3 and 4.
(b) Check continuity between terminals.
OK:
Terminals 1 and 2Continuity
NG Replace ABS motor relay.
OK
4 Check for open and short in harness and connector between ABS motor relay
and ABS ECU (See page IN-28).
NG Repair or replace harness or connector.
OK
If the same code is still output after the DTC is deleted, check the contact condition of each con-
nection.
If the connections are normal, the ECU may be defective.

BR3583
BR3582F00010
RotorSpeed Sensor
CoilNSMagnet
To ECU
Low Speed
High Speed
+V
-V
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-469
697 Author
: Date
:
1997 SUPRA (RM502U)
DTC 31, 32, 33, 34 Speed Sensor Circuit
CIRCUIT DESCRIPTION
The speed sensor detects the wheel speed and sends the ap-
propriate signals to the ECU. These signals are used to control
the ABS control system. The front and rear rotors each have 48
serrations.
When the rotos rotate, the magnetic field emitted by the perma-
nent magnet in the speed sensor generates an AC voltage.
Since the frequency of this AC voltage changes in direct propor-
tion to the speed of the rotor, the frequency is used by the ECU
to detect the speed of each wheel.
DTC No.DTC Detecting ConditionTrouble Area
31,32,33,34
Detection of any of conditions (1) through (3):
(1) At vehicle speed of 10 km/h (6 mph) or more, pulses are
not input for 15 sec.
(2) Momentary interruption of the vehicle speed sensor signal
occurs at least 7 times in the time between switching the igni-
tion switch ON and switching it OFF.
(3) Abnormal fluctuation of speed sensor signals with the ve-
hicle speed 20 km/h (12 mph) or more.

Right front, left front, right rear and left rear speed sensor

Open or short in each speed sensor circuit

Sensor rotor
HINT:
DTC No.31 is for the right front speed sensor.
DTC No.32 is for the left front speed sensor.
DTC No.33 is for the right rear speed sensor.
DTC No.34 is for the left rear speed sensor.
Fail safe function:
If trouble occurs in the speed sensor circuit, the ECU cuts off current to the ABS solenoid relay and prohibits
ABS control.
DI4VE-01

F03330
Battery
B
R/B No.2
ALT
2222AM1 R/B No.2
WR/B No.1
W
2
IG Switch
J/B No.1ABS ECU
IG1
GND1
GND2 ECU IG
444
513 B-Y
1B1J1J 1K A18A20
213*1
*2
A20
A20 A19
A19212
13 25W-B
W-B W-B W-B
IG
IEW-B
*2
NORMAL ABS (2JZ-GE Engine)
SPORT ABS (2JZ-GTE Engine)*1:
*2:
W
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-475
703 Author
: Date
:
1997 SUPRA (RM502U)
DTC 41 IG Power Source Circuit
CIRCUIT DESCRIPTION
This is the power source for the ECU, hence the CPU and the actuators.
DTC No.DTC Detecting ConditionTrouble Area
41Voltage at ECU terminal IG1 is less than 9.5 V for more than
10 sec. while vehicle speed is 3 km/h (1.9 mph) or more.
Battery

IC regulator

Open or short in power source circuit
Fail safe function:
If trouble occurs in the power source circuit, the ECU cuts off current to the ABS solenoid relay and prohibits
ABS control.
WIRING DIAGRAM
DI4VF-01

DI-484
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
712 Author
: Date
:
1997 SUPRA (RM502U)
DTC 51 ABS Pump Motor Lock
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
51Pump motor is not operating normally during initial check.
ABS pump motor
Fail safe function:
If trouble occurs in the ABS pump motor, the ECU cuts off the current to the ABS solenoid relay and prohibits
ABS control.
WIRING DIAGRAM
See page DI-460.
INSPECTION PROCEDURE
See inspection of ABS actuator (See page BR-66 or BR-66).
DI4VJ-01

F03345
R/B No.2ABS ECU*1
*2
W21B22
B
Battery
NORMAL ABS (2JZ-GE Engine)
SPORT ABS (2JZ-GTE Engine)
*1:
*2:
ALTW
R/B No.2
J/B No.12AM1 W1J
442
IG Switch
4 B-Y
J/B No.1
1J1KECU-IG513A18A20 213
212
1325IG 1
GND1
GND2 A20
A20 A19
A19 W-B
W-B W-B
W-B
W-B
*2IE IG
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-485
713 Author
: Date
:
1997 SUPRA (RM502U)
DTC Always ON Malfunction in ECU IG Power Source
Circuit
CIRCUIT DESCRIPTION
This is the power source for the ECU, hence the CPU, and the actuators.
DTC No.DTC Detecting ConditionTrouble Area
Always ONVoltage of ECU terminal IG1 remains at more than 17 V for 1
sec. or more.

Battery

IC regulator

Open or short in power source circuit

ECU
Fail safe function:
If trouble occurs in the power source circuit, the ECU cuts off current to the ABS solenoid relay and prohibits
ABS control.
WIRING DIAGRAM
DI4VK-01

DI-486
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
714 Author
: Date
:
1997 SUPRA (RM502U)
INSPECTION PROCEDURE
1 Is DTC output?
Check DTC on page DI-442.
YES Repair circuit indicated by the code output.
NO
2 Is normal code displayed?
YES Check ABS solenoid relay. Check for short in
harness and connector between ABS solenoid
relay and DLC1 (See page IN-28).
NO
3 Is ABS warning light go off?
YES Check for open or short in harness and conec-
tor between ECU-IG Fuse and ECU
(See page IN-28).
NO
4 Check battery positive voltage.
PREPARATION:
Start the engine.
CHECK:
Check the battery positive voltage.
OK:
Voltage: 10 - 16 V
NG Check and repair the charging system.
OK

F03346F03347F03348
2JZ-GE Engine (NORMAL ABS):
2JZ-GTE Engine (SPORT ABS):Battery
ABS Control RelayJ/B No.1
(Motor
Relay)
(Solenoid
Relay)
W-B
1
2
6
A9
4
3
1
4
A9B-R
EA1
6
23 B-R
22
DLC1 Short Pin
L16
IJ1
A18
4
LLL
IF212
L42
ABS
Warning
Light
Y
GAUGE
ABS ECU1J1E
512
25
ABS ActuatorABS ECU
12 V
WA
EA
Battery
R/B No.5
ABS
Solenoid Relay15
5
5555 26
4
5 3
W-B
EA
ABS Actuator
B-R
EA16
23 B-R
Short Pin
DLC1
22L16
IJ1L
L
L11A20WA12 V ABS ECU
ABS
Warning
Light
L4
IF212
2 Y
GAUGE J/B No.1
1J
1E
12 5
ABS & TRAC
ECU DI-488
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
716 Author
: Date
:
1997 SUPRA (RM502U)
ABS Warning Light Circuit
CIRCUIT DESCRIPTION
If the ECU detects trouble, it lights the ABS warning light while at the same time prohibiting ABS control. At
this time, the ECU records a DTC in memory.
After removing the short pin of the DLC1, connect terminals Tc and E1 of the DLC1 or DLC2 to make the
ABS warning light to blink and output the DTC.
WIRING DIAGRAM
DI4VL-01