spare wheel TOYOTA SUPRA 1997 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1997, Model line: SUPRA, Model: TOYOTA SUPRA 1997Pages: 1807, PDF Size: 39.36 MB
Page 263 of 1807
BO0QA-01
N11813
Spare Wheel Cover
Deck Trim Side Board RH
Quarter Wheel House
Inner Cover RH
Quarter Wheel House Inner
Cover LHSport Roof:
Stay Support CoverRemovable
Roof Stay
Lower Back Service
Hole Cover
Deck Trim Rear Cover
Deck Trim Rear Cover
Deck Trim Side Board LH
ReinforcementLicense Plate Light
Rear Combination Light
End Retainer RH
Rear Bumper Cover
End Retainer No.2
End Retainer LH Energy Absorber
42 (430, 31)
5.9 (60, 52 in.´lbf)
N´m (kgf´cm, ft´lbf) : Specified torque
- BODYREAR BUMPER
BO-5
2085 Author: Date:
1997 SUPRA (RM502U)
REAR BUMPER
COMPONENTS
Page 271 of 1807
BO0QG-01
N19401
Back Door
Damper StayCenter Stop Light
Tonneau Cover Retractor
Back Door
Trim Board
Lock Striker
Lock Cylinder
Back Door Lock
Sport Roof:
Removable
Roof HolderHolder Garnish
Stay Support Cover
Removable Roof Stay
Lower Back Service Hole Cover Rear Seatback
Roof Side Inner Garnish
Front Seat
Outer Belt
Rear Seat Cushion
Tonneau Cover
Luggage Compartment Mat
Spare Wheel Cover
Deck Trim Rear Cover Deck Trim Side Board
Quarter Wheel House
Inner Cover
Rear Seat Outer Belt Speaker Grille Rear Quarter
Trim Board
Precoated part
7.8 (80, 69 in.´lbf)
13 (130, 9.4)
19 (195, 14)
5.9 (60, 52 in.´lbf)
N´m (kgf´cm, ft´lbf): Specified torque
43 (440, 32)
43 (440, 32)
BO-14
- BODYBACK DOOR
2094 Author: Date:
1997 SUPRA (RM502U)
BACK DOOR
COMPONENTS
Page 293 of 1807
BO0R2-01
N19533
Tonneau Cover
Deck Trim Rear Cover
Coat Hook
Roof Side Inner Garnish
Tonneau Cover Clamp
Quarter Wheel House
Inner Cover
Deck Trim Side Board
Rear Seat
Outer Belt
Quarter Window
Glass
Roof Side Rail Weatherstrip
Retainer
Roof Side Rail Weatherstrip Speaker Grille Front Seat
Outer Belt
Deck Trim Side Service Hole Cover
Front Door Scuff
Inside Plate
Outside Garnish Seal Rear Seatback
5X
Sport Roof:Lower Back Service
Hole Cover
Removable Roof Stay
Stay Support Cover
Holder Garnish
Removable Roof Holder Luggage Compartment Mat
Spare Wheel Cover Rear Seat Cushion
Non-reusable partRear Quarter Trim Board
43 (440, 32)
25 (260, 19)
N´m (kgf´cm, ft´lbf) : Specified torque
- BODYQUARTER WINDOW GLASS
BO-37
2117 Author: Date:
1997 SUPRA (RM502U)
QUARTER WINDOW GLASS
COMPONENTS
Page 294 of 1807
BO0R3-01
N09045
Butyl Tape
: 3 Clips
N09040
Outside Garnish Seal BO-38
- BODYQUARTER WINDOW GLASS
2118 Author: Date:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE THESE PARTS:
(See pages BO-61)
(a) Tonneau cover
(b) Luggage compartment mat
(c) Spare wheel cover
(d) Rear seatback
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(e) Removable roof stay RH and LH (Sport roof)
(f) Deck trim rear cover
(g) Removable roof holder (Sport roof)
(h) Quarter wheel house inner cover
(i) Speaker grille
(j) Deck trim side board
(k) Front door scuff inside plate
(l) Rear quarter trim board
(m) Front seat outer belt shoulder anchor
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(n) Rear seat outer belt floor anchor
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(o) Roof side inner garnish
(p) Rear roof headlining (Sport roof)
2. REMOVE ROOF SIDE RAIL WEATHERSTRIP
(a) Using a clip remover, remove the 3 clips from the rear side
of the weatherstrip.
(b) Remove the rear side of the weatherstrip from the retain-
er.
3. REMOVE ROOF SIDE RAIL WEATHERSTRIP RETAIN-
ER
Remove the outside garnish seal and retainer.
Page 314 of 1807
BO0RF-01
N19535
Sport Roof:
Roof Side Rail Weatherstrip RH
Removable Roof Moulding RH
Removable Roof Headlining
Front Pillar GarnishRear Roof Headlining
Front Roof
Headlining
Assist Grip Removable Roof
Moulding LH Roof Side Rail
Weatherstrip LH Roof Headlining
Visor Holder
Sun VisorInterior LightClip
Front Pillar GarnishRoof Side Inner GarnishCoat Hook
Deck Trim Side BoardTonneau Cover
Tonneau
Cover
Clamp
Deck Trim Rear Cover
Quarter Wheel House Cover
Rear Seat Outer Belt
Speaker Grille Assist GripFront Seat
Outer Belt
Deck Trim
Side Service
Hole Cover
Front Door Scuff Inside Plate
Rear Quarter Trim Board
Rear Seatback
5XLuggage Compartment Mat
Rear Seat Cushion
Spare Wheel Cover
Non-reusable partSport Roof:
Removable Roof StayLower Back Service
Hole Cover
Stay Support Cover
Holder Garnish
Removable Roof Holder
43 (440, 32)
43 (440, 32)
25 (260, 19)
N´m (kgf´cm, ft´lbf) : Specified torqueClip
BO-60
- BODYROOF HEADLINING
2140 Author: Date:
1997 SUPRA (RM502U)
ROOF HEADLINING
COMPONENTS
Page 315 of 1807
BO0RG-01
N08498
N08499
N08501
3 Clips
2 Clips
N08502
- BODYROOF HEADLINING
BO-61
2141 Author: Date:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE THESE PARTS:
(a) Tonneau cover
(b) Luggage compartment mat
(c) Spare wheel cover
(d) Rear seat cushion
(e) Rear seatback
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(f) Removable roof stay RH and LH (Sport roof)
(g) Deck trim rear cover
(h) Removable roof holder RH and LH (Sport roof)
(i) Quarter wheel house cover
(j) Deck trim side boards
(k) Front door scuff inside plates
(l) Speaker grilles
(m) Rear quarter trim boards
(n) Front seat outer belts
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(o) Rear seat outer belts
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(p) Deck trim side service hole covers
Page 320 of 1807
BO0RT-01
N19399
Rear Seatback
Rear Seat Cushion
Seat Hook
Roof Side Inner GarnishTonneau Cover
Luggage Compartment
Mat
Spare Wheel Cover
Sport Roof:
Holder Garnish
Removable Roof Holder
Tonneau Cover
ClampDeck Trim Side Board
Deck Trim Rear Cover
Rear Quarter
Trim Board Quarter Wheel
House Inner Cover
Quarter Wheel
House Inner
Front Cover
Speaker Grille
Front Door Scuff Inside Plate
Rear Seat Outer BeltSport Roof:
Lower Back
Service Hole Cover
Stay Support
Cover
Rear Seat Inner Belt
Seat Track Cover Front Seat
Outer BeltFront Seat
Front Seat Cushion
Inner Shield
Seat Track CoverFront Seat Inner Belt
43 (440, 32)
7.8 (80, 69 in.´lbf)
43 (440, 32)
43 (440, 32)
43 (440, 32)
43 (440, 32)
43 (440, 32)
43 (440, 32): Specified torqueN´m (kgf´cm, ft´lbf)
- BODYSEAT BELT
BO-67
2147 Author: Date:
1997 SUPRA (RM502U)
SEAT BELT
COMPONENTS
Page 1441 of 1807
AB0163
Wire Harness
Diameter
Stripped Wire Harness Section
R05751
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS-15
1954 Author: Date:
1997 SUPRA (RM502U)
(2) Using a service-purpose wire harness tie down the
steering wheel pad to the disc wheel.
Wire harness: Stripped wire harness section
1.25 mm
2
or more (0.0019 in2. or more).
HINT:
To calculate the square of the stripped wire harness section:
Square - 3.14 x (Diameter)
2
divided by 4
CAUTION:
If a wire harness which is too thin or some other thing is
used to tie down the steering wheel pad, it may be snapped
by the shock when the airbag is deployed. This is highly
dangerous. Always use a wire harness for vehicle use
which is at least 1.25 mm
2
(0.0019 in2).
(3) Using 3 wire harness, wrap the wire harness at least
2 times each around the bolts installed on the left
and right sides of the steering wheel pad.
CAUTION:
Tightly wind the wire harness around the bolts so that
there is no slack.
If there is slackness in the wire harness, the steering
wheel pad may come loose due to the shock when the
airbag is deployed. This is highly dangerous.
(4) Face the upper surface of the steering wheel pad
upward. Separately tie the left and right sides of the
steering wheel pad to the disc wheel through the
hub nut holes. Position the steering wheel pad con-
nector so that it hangs downward though a hub hole
in the disc wheel.
CAUTION:
Make sure that the wire harness is tight. It is very dan-
gerous when looseness in the wire harness results in
the steering wheel pad coming free through the shock
from the airbag deploying.
Always tie down the steering wheel pad with the pad
side facing upward. It is very dangerous if the steer-
ing wheel pad is tied down with the metal surface fac-
ing upward as the wire harness will be cut by the
shock of the airbag deploying and the steering wheel
pad will be thrown into the air.
NOTICE:
The disc wheel will be marked by airbag deployment, so
use the spare disc wheel.
Page 1443 of 1807
R04211
Inner Diam.
Tires
(3 or More)Width
H03208
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS-17
1956 Author: Date:
1997 SUPRA (RM502U)
Covering method using tires:
Place at least 3 tires without disc wheel on top of the
disc wheel with tire to which the steering wheel pad
is tied.
Tire size: Must exceed the following dimensions-
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
Do not use tires with disc wheels.
NOTICE:
The tires may be marked by the airbag deployment, so use
the spare tires.
(f) Deploy the airbag.
(1) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(-) terminal.
(2) Check that no one is within 10 m (33 ft) area around
the disc wheel which the steering wheel pad is tied
to.
(3) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys simultaneously as the LED of the SST ac-
tivation switch lights up.
(g) Dispose of the steering wheel pad (with airbag).
CAUTION:
The steering wheel pad is very hot when the airbag is
deployed, so leave it alone for at least 30 minutes af-
ter deployment.
Use gloves and safety glasses when handling a steer-
ing wheel pad with deployed airbag.
Always wash your hands with water after completing
the operation.
Do not apply water, etc. to a steering wheel pad with
deployed airbag.
(1) Remove the steering wheel pad from the disc
wheel.
(2) Place the steering wheel pad in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts disposal.
Page 1466 of 1807
Q08242
TOYOTA Hand-Held Tester
DLC3
P12563
Disconnect
Plug SF-6
- SFI (2JZ-GTE)FUEL PUMP
1332 Author: Date:
1997 SUPRA (RM502U)
(f) Connect the TOYOTA hand-held tester to the DLC3.
(See step 1 in check fuel pump operation (a) to (e).)
(g) Reconnect the negative (-) terminal cable to the battery.
(h) Turn the ignition switch ON.
(i) Measure the fuel pressure.
Fuel pressure:
226 - 275 kPa (2.3 - 2.8 kgf/cm
2, 33 - 40 psi)
If pressure is high, replace the fuel pressure regulator.
If pressure is low, check the following parts:
(1) Fuel hoses and connections
(2) Fuel pump
(3) Fuel filter
(4) Fuel pressure regulator
(j) Remove the TOYOTA hand-held tester from the
DLC3.
(k) Start the engine.
(l) Disconnect the vacuum sensing hose from the fuel pres-
sure regulator, and plug the hose end.
(m) Measure the fuel pressure at idle.
Fuel pressure:
226 - 275 kPa (2.3 - 2.8 kgf/cm
2, 33 - 40 psi)
(n) Reconnect the vacuum sensing hose to the fuel pressure
regulator.
(o) Measure the fuel pressure at idle.
Fuel pressure:
167 - 216 kPa (1.7 - 2.2 kgf/cm
2, 24 - 31 psi)
If pressure is not as specified, check the vacuum sensing hose
and fuel pressure regulator.
(p) Stop the engine.
(q) Check that the fuel pressure remains as specified for 5
minutes after the engine has stopped.
Fuel pressure:
147 kPa (1.5 kgf/cm
2, 21 psi) or more
If pressure is not as specified, check the fuel pump, pressure
regulator and/or injectors.
(r) After checking fuel pressure, disconnect the negative (-)
terminal cable from the battery and carefully remove the
SST to prevent gasoline from splashing.
SST 09268-45012
(s) Reinstall the fuel inlet hose to the fuel filter with 2 new gas-
kets and the union bolt.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
(t) Reconnect the negative (-) terminal cable to the battery.
(u) Check for fuel leaks.
3. TAKE OUT FLOOR CARPET
4. REMOVE SPARE WHEEL COVER
5. REMOVE SPARE WHEEL
6. REMOVE SERVICE HOLE COVER
7. DISCONNECT FUEL PUMP & SENDER GAUGE CON-
NECTOR