TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine IG03Q−03
− IGNITION (5VZ−FE)IGNITION COIL
IG−7
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE AIR CLEANER CAP AND MAF METER AS-
SEMBLY
2. DISCONNECT HIGH−TENSION CORDS FROM
IGNITION COILS
(See page IG−1)
3. REMOVE IGNITION COILS
(a) Disconnect the 3 connectors from the ignition coils.
(b) Remove the 3 bolts and 3 ignition coils from the LH cylin-
der head.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)
HINT:
Arrange the ignition coils in correct order.

Downloaded from www.Manualslib.com manuals search engine IG03R−01
IG−8
− IGNITION (5VZ−FE)IGNITION COIL
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page IG−7).

Downloaded from www.Manualslib.com manuals search engine IG03S−03
− IGNITION (5VZ−FE)CAMSHAFT POSITION SENSOR
IG−9
1164 Author: Date:
1996 TOYOTA T100 (RM449U)
CAMSHAFT POSITION SENSOR
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine IG03T−03
P20432
IG−10
− IGNITION (5VZ−FE)CAMSHAFT POSITION SENSOR
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE UPPER RADIATOR HOSE
2. REMOVE NO. 2 TIMING BELT COVER
(a) Remove the high−tension cord clamps from the No. 2 tim-
ing belt cover.
(b) Remove the PS pump hose from the No. 2 timing belt cov-
er clamp.
(c) Remove the 6 bolts and No. 2 timing belt cover.
3. REMOVE CAMSHAFT POSITION SENSOR
(a) Disconnect the camshaft position sensor connector.
(b) Remove the bolts and camshaft position sensor.
Torque:7.8 N·m (80 kgf·cm, 69 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine IG03U−02
− IGNITION (5VZ−FE)CAMSHAFT POSITION SENSOR
IG−11
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page IG−10).

Downloaded from www.Manualslib.com manuals search engine P20434
IG03V−03
IG−12
− IGNITION (5VZ−FE)CRANKSHAFT POSITION SENSOR
1167 Author: Date:
1996 TOYOTA T100 (RM449U)
CRANKSHAFT POSITION SENSOR
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. REMOVE CRANKSHAFT POSITION SENSOR
(a) Disconnect the crankshaft position sensor connector.
(b) Remove the bolt crankshaft position sensor.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine IG03W−01
P20431
Ohmmeter
− IGNITION (5VZ−FE)CRANKSHAFT POSITION SENSOR
IG−13
1996 TOYOTA T100 (RM449U)
INSPECTION
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the sensor itself. ”Cold” is from −10°C
(14°F) to 50°C (122°F) and ”Hot” is from 50°C (122°F) to
100°C (212°F).
INSPECT CRANKSHAFT POSITION SENSOR
RESISTANCE
Using an ohmmeter, measure the resistance between termi-
nals.
Resistance:
Cold: 1,630 − 2,740 Ω
Hot: 2,065 − 3,225 Ω
If the resistance is not as specified, replace the crankshaft posi-
tion sensor.

Downloaded from www.Manualslib.com manuals search engine IG03X−02
IG−14
− IGNITION (5VZ−FE)CRANKSHAFT POSITION SENSOR
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page IG−12).

Downloaded from www.Manualslib.com manuals search engine ST – STARTING (3RZ-FE)

STARTER ST-1
STARTER RELAY ST-17

Downloaded from www.Manualslib.com manuals search engine ST02W−03
B01307
Starter Wire
Starter ConnectorStarter
− STARTING (3RZ−FE)STARTER
ST−1
1170 Author: Date:
1996 TOYOTA T100 (RM449U)
STARTER
COMPONENTS