oil pressure TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine MA001−28
− MAINTENANCEOUTSIDE VEHICLE
MA−1
36 Author: Date:
1996 TOYOTA T100 (RM449U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts.
If necessary, tighten them.
4. TIRE ROTATION
Check the owner’s manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

Downloaded from www.Manualslib.com manuals search engine − PREPARATIONENGINE MECHANICAL (3RZ−FE)
PP−3
52 Author: Date:
1996 TOYOTA T100 (RM449U)
(09248−05420)Valve Lifter Stopper
09325−20010Transmission Oil Plug
09330−00021Companion Flange Holding ToolCrankshaft pulley
09550−10012Replacer Set ”B”
(09252−10010)No. 1 Replacer Handle−Valve guide busing
09608−30012Front Hub & Drive Pinion Bearing
Tool Set−
(09951−07100)Handle 100Crankshaft rear oil seal
09636−20010Upper Ball Joint Dust Cover
ReplacerCrankshaft timing gear
09816−30010Oil Pressure Switch SocketKnock sensor
09843−18020Diagnosis Check Wire
09950−40010Puller B Set
(09951−04010)Hanger 150
(09952−04010)Slide Arm

Downloaded from www.Manualslib.com manuals search engine − PREPARATIONENGINE MECHANICAL (5VZ−FE)
PP−9
58 Author: Date:
1996 TOYOTA T100 (RM449U)
(09248−05420)Valve Lifter Stopper
09330−00021Companion Flange Holding ToolCrankshaft pulley
09816−30010Oil Pressure Switch SocketOil pressure switch
09843−18020Diagnosis Check Wire
09950−50010Puller C Set
(09951−05010)Hanger 150Crankshaft pulley
Crankshaft timing pulley
(09952−05010)Slide ArmCrankshaft pulley
Crankshaft timing pulley
(09953−05020)Center Bolt 150Crankshaft pulley
Crankshaft timing pulley
(09954−05010)Claw No.1Crankshaft timing pulley
(09954−05030)Claw No.3Crankshaft pulley
09950−70010Handle Set
(09951−07150)Handle 150Crankshaft rear oil seal
Valve guide bushing
09960−10010Variable Pin Wrench Set

Downloaded from www.Manualslib.com manuals search engine PP0GC−02
− PREPARATIONMFI (3RZ−FE)
PP−19
68 Author: Date:
1996 TOYOTA T100 (RM449U)
MFI (3RZ−FE)
SST (Special Service Tools)
09268−41046Injection Measuring Tool Set
(09268−41091)NO.7 Union
(90405−09015)No.1 Union
09268−45012EFI Fuel Pressure Gauge
09631−22020Power Steering Hose Nut
14 x 17 mm Wrench SetFuel line flare nut
09816−30010Oil Pressure Switch SocketKnock sensor
09842−30070Wiring ”F” EFI Inspection
09843−18020Diagnosis Check Wire

Downloaded from www.Manualslib.com manuals search engine PP330−01
PP−22
− PREPARATIONSFI (5VZ−FE)
71 Author: Date:
1996 TOYOTA T100 (RM449U)
SFI (5VZ−FE)
SST (Special Service Tools)
09268−41046Injection Measuring Tool Set
(09268−41091)NO.7 Union
(09268−52011)Injection Measuring Attachment
09268−45012EFI Fuel Pressure Gauge
09631−22020Power Steering Hose Nut
14 x 17 mm Wrench SetFuel line flare nut
09816−30010Oil Pressure Switch Socket
09842−30070Wiring ”F” EFI Inspection
09843−18020Diagnosis Check Wire

Downloaded from www.Manualslib.com manuals search engine PP0GJ−02
− PREPARATIONLUBRICATION (3RZ−FE)
PP−35
1996 TOYOTA T100 (RM449U)
EQUIPMENT
Oil pressure gauge
Precision straight edgeOil pump
Torque wrench

Downloaded from www.Manualslib.com manuals search engine PP01R−01
PP−38
− PREPARATIONLUBRICATION (5VZ−FE)
87 Author: Date:
1996 TOYOTA T100 (RM449U)
LUBRICATION (5VZ−FE)
SST (Special Service Tools)
09032−00100Oil Pan Seal Cutter
09228−07501Oil Filter Wrench
09309−37010Transmission Bearing ReplacerCamshaft front oil seal
09816−30010Oil Pressure Switch Socket

Downloaded from www.Manualslib.com manuals search engine PP01T−02
PP−40
− PREPARATIONLUBRICATION (5VZ−FE)
1996 TOYOTA T100 (RM449U)
EQUIPMENT
Oil pressure gauge
Precision straight edgeOil pump
Torque wrench

Downloaded from www.Manualslib.com manuals search engine SS092−01
SS−4
− SERVICE SPECIFICATIONSENGINE MECHANICAL (3RZ−FE)
178 Author: Date:
1996 TOYOTA T100 (RM449U)
ENGINE MECHANICAL (3RZ−FE)
SERVICE DATA
Valve
clearance
(Cold)Intake
Exhaust0.15 − 0.25 mm (0.006 − 0.010 in.)
0.25 − 0.35 mm (0.010 − 0.014 in.)
Ignition timing3 − 7° BTDC @ idle
Idle speed650 − 750 rpm
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,230 kPa (12.5 kgf/cm2, 178 psi) or more
880 kPa (9.0 kgf/cm2, 127 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Cylinder headWarpage
Cylinder block side Maximum
Manifold sideMaximum
Valve seat
Refacing angleIntake
Exhaust
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.05
Cylinder head bolt outside diameter STD
Minimum
0.05 mm (0.0020 in.)
0.10 mm (0.0039 in.)
30°, 45°, 60°
45°, 60°
45°
1.0 − 1.4 mm (0.039 − 0.055 in.)
11.000 − 11.027 mm (0.4331 − 0.4341 in.)
11.050 − 11.077 mm (0.4350 − 0.4361 in.)
10.76 − 10.97 mm (0.4236 − 0.4319 in.)
10.40 mm (0.4094 in.)
Valve guide
bushingInside diameter
Protrusion height
Replacing temperature (Cylinder head side)6.010 − 6.030 mm (0.2366 − 0.2374 in.)
8.2 − 8.6 mm (0.323 − 0.339 in.)
80 − 100°C (176 −212°F)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Minimum Intake
Exhaust
Margin thickness STD
Minimum103.45 mm (4.0728 in.)
103.60 mm (4.0787 in.)
102.95 mm (4.0531 in.)
103.10 mm (4.0590 in.)
44.5°
5.970 − 5.985 mm (0.2350 − 0.2356 in.)
5.965 − 5.980 mm (0.2348 − 0.2354 in.)
0.025 − 0.060 mm (0.0010 − 0.0024 in.)
0.030 − 0.065 mm (0.0012 − 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.0 mm (0.039 in.)
0.5 mm (0.020 in.)
Valve springDeviation Maximum
Installed tension at 37.5 mm (1.406 in.)2.0 mm (0.079 in.)
177 − 204 N (18.0 − 20.0 kgf, 45.9 − 39.7 lbf)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum30.966 − 30.976 mm (1.1578 − 1.2195 in.)
31.000 − 31.016 mm (1.2205 − 1.2211 in.)
0.024 − 0.055 mm (0.0009 − 0.0022 in.)
0.07 mm (0.0028 in.)
ManifoldWarpageMaximum Intake
Exhaust0.20 mm (0.0078 in.)
0.50 mm (0.0197 in.)
Air intake
chamberWarpage Maximum0.20 mm (0.0078 in.)

Downloaded from www.Manualslib.com manuals search engine SS00O−07
− SERVICE SPECIFICATIONSENGINE MECHANICAL (5VZ−FE)
SS−9
183 Author: Date:
1996 TOYOTA T100 (RM449U)
ENGINE MECHANICAL (5VZ−FE)
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,200 kPa (12.2 kgf/cm2, 174 psi)
1,000 kPa (10.2 kgf/cm2, 145 psi)
100 kPa (1.0 kgf/cm2, 15 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim for repair part Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.13 − 0.23 mm (0.006 − 0.009 in.)
0.27 − 0.37 mm (0.011 − 0.014 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC18 − 12° BTDC @ idle
Idle speed−700 ± 50 rpm
Intake manifold
vacuumat idle speed60 kPa (450 mmHg, 17.7 in.Hg) or more
Timing belt
tensionerProtrusion from housing side10.0 − 10.8 mm (0.394 − 0.425 in.)
Cylinder headWarpage Maximum
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.050.10 mm (0.039 in.)
30°, 45°, 60°
45°
1.0 − 1.4 mm (0.039 − 0.055 in.)
10.985 − 11.027 mm (0.4325 − 0.4341 in.)
11.050 − 11.077 mm (0.4350 − 0.4361 in.)
Valve guide
bushingInside diameter
Outside diameter for repair part STD
O/S 0.056.010 − 6.030 mm (0.2366 − 0.2374 in.)
11.033 − 11.044 mm (0.4344 − 0.4348 in.)
11.083 − 11.094 mm (0.4363 − 0.4368 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum95.15 mm (3.7461 in.)
94.90 mm (3.7362 in.)
94.60 mm (3.7244 in.)
94.40 mm (3.7165 in.)
44.5°
5.970 − 5.985 mm (0.2350 − 0.2356 in.)
5.965 − 5.980 mm (0.2348 − 0.2354 in.)
0.025 − 0.060 mm (0.0010 − 0.0024 in.)
0.030 − 0.065 mm (0.0012 − 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.0 mm (0.039 in.)
0.5 mm (0.020 in.)