trip computer TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine FI0534
DI0T7−03
FI7231
TOYOTA Hand−Held Tester
DLC3
− DIAGNOSTICSENGINE (3RZ−FE)
DI−3
1996 TOYOTA T100 (RM449U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand−
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on−
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Code (DTC) prescribed by SAE J2012 are
recorded in the ECM memory (See page DI−13).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTCs remain recorded in the ECM memory.
To check the DTCs, connect the OBD II scan tool or
TOYOTA hand−held tester to the Data Link Con-
nector 3 (DLC3) on the vehicle. The OBD II scan
tool or TOYOTA hand−held tester also enables you
to erase the DTCs and check freezed frame data
and vaious forms of engine data (For operating
instructions, see the OBD II scan tool’s instruction
book.).
DTCs include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI−13).
The diagnosis system operates in normal mode
during normal vehicle use. It also has a check mode
for technicians to simulate malfunction symptoms
and troubleshoot. Most DTCs use 2 trip detection
logic* to prevent erroneous detection, and ensure
thorough malfunction detection. By switching the
ECM to check mode when troubleshooting, the
technician can cause the MIL to light up for a mal-
function that is only detected once or momentarily
(TOYOTA hand−held tester only) (See step 2).
*2 trip detection logic: When a logic malfunction is
first detected, the malfunction is temporarily stored
in the ECM memory. If the same malfunction is de-
tected again during the 2nd drive test, this 2nd
detection causes the MIL to light up.

Downloaded from www.Manualslib.com manuals search engine A00652
ECM VSV for EVAP
Throttle
Valve
Fuel Tank Charcoal
CanisterFig 1
A00647
IG Switch
(M/T)(A/T)
23W−G
2
1
EFI
EFI Relay
VSV for
ECM From From
Battery
22
2
2
223 2
E7 E5
EA
W−B
IE2W−G1 R/B No.2
PRG
E01 4EVAP5
EA1
W−RW−R
921
B−W
DI−88
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
DTC P0441 Evaporative Emission Control System
Incorrect Purge Flow
CIRCUIT DESCRIPTION
To reduce HC emissions, evaporated fuel from the fuel tank is
routed through the charcoal canister to the intake manifold for
combustion in the cylinders.
The ECM changes the duty signal to the VSV for EVAP so that
the intake quantity of HC emissions is appropriate for the driving
conditions (engine load, engine speed, vehicle speed, etc.) af-
ter the engine is warmed up.
DTC No.DTC Detecting ConditionTrouble Area
P0441Proper response to computer command does not occur
(2 trip detection logic)
Open or short in VSV circuit for EVAP
VSV for EVAP
ECM
Vacuum hose cracks, hole, blocked, damaged or
disconnected
Charcoal canister
WIRING DIAGRAM
DI0TX−03

Downloaded from www.Manualslib.com manuals search engine FI0534
DI0UB−02
FI7231
TOYOTA Hand−Held Tester
DLC 3
− DIAGNOSTICSENGINE (5VZ−FE)
DI−129
1996 TOYOTA T100 (RM449U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand−
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on−
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Codes (DTCs) prescribed by SAE J2012
are recorded in the ECM memory (See page
DI−140).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTCs remain recorded in the ECM memory.
To check the DTCs, connect the OBD II scan tool or
TOYOTA hand−held tester to the Data Link Con-
nector 3 (DLC3) on the vehicle. The OBD II scan
tool or TOYOTA hand−held tester also enables you
to erase the DTCs and check freezed frame data
and various forms of engine data (For operating
instructions, see the OBD II scan tool’s instruction
book.).
DTCs include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI−140).

Downloaded from www.Manualslib.com manuals search engine A00653
w/o Tachometer
w/ Tachometer
DI0VF−02
Q08498
TOYOTA Hand−Held Tester
DLC3
− DIAGNOSTICSAUTOMATIC TRANSMISSION
DI−265
1996 TOYOTA T100 (RM449U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle an OBD II scan
tool complying with SAE J1978 or TOYOTA hand−
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on−
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable DTCs pre-
scribed by SAE J2012 are recorded in the ECM
memory.
(3RZ−FE: See page DI−13)
(5VZ−FE: See page DI−140)
If the malfunction only occurs in 3 trips, the MIL goes off but the
DTCs remain recorded in the ECM memory.
To check the DTCs, connect an OBD II scan tool or
TOYOTA hand−held tester to DLC3 on the vehicle.
The OBD II scan tool or TOYOTA hand−held tester
also enables you to erase the DTCs and check
freeze frame data and various forms of engine data
(For instruction book).
DTCs include SAE controlled codes and Manufac-
turer controlled codes.
SAE controlled codes must be set as prescribed by
the SAE, while Manufacturer controlled codes can
be set freely by the manufacturer within the pre-
scribed limits (See DTC chart on page DI−276).