lock TOYOTA T100 1997 User Guide

17
ADJUSTING SEAT POSITION
Pull the lock release lever up. Then
slide the seat to the desired position
with slight body pressure and release
the lever.
ADJUSTING SEATBACK ANGLE(except non-split bench seat)
Lean forward and pull the lever up.
Then lean back to the desired angle
and release the lever.
CAUTION!
To reduce the risk of sliding under
the lap belt during a collision, avoid
reclining the seatback any more
than needed. The seat belts provide
maximum protection when the driv-
er and the passenger are sitting up
straight and well back in the seats. If
you are reclined, the lap belt may
slide past your hips and apply re- straint forces directly to the abdo-
men. Therefore, in the event of a
frontal collision, the risk of personal
injury may increase with increasing recline of the seatback. ADJUSTING DRIVER'S SEAT CUSH-
ION ANGLE (separate seat only)
Turn the knob either way.
ADJUSTING DRIVER'S SEAT LUM-
BAR SUPPORT (separate seat only) Pull the lever forward and rerlease. Repeat this until you have a comfortable support.For easy access to the rear seat, do this.
1. Lift the seatback lock release lever or
press the release pedal.
The seat will slide forward slightly.
2. Move the seat to the front-most posi- tion.
After passengers are in, lift up on the seat-
back and return the seat until it locks.
ÐMoving passenger's seat for rear seat entry (Xtra-cab models)

18
CAUTION!
After putting back the seat, try
pushing the seat forward and rear-
ward to make sure it is secured inplace.
Never allow anyone to rest their
foot on the release pedal while the
vehicle is moving.
Unlock the seatback, and fold it down.
Hold the lock release lever until you have
swung the seatback forward slightly.
CAUTION!
When returning the seatback to the
upright position: Make sure the seat belts are not
twisted or caught in the seatback
and are arranged in their proper
position for ready use.
Make sure the seatback is secure-
ly locked by pushing forward and rearward on the top of the seat- back.
BEFORE RAISING REAR SEAT
Stow the rear seat belts as shown in
the illustration.
This prevents the belts from falling out
when you raise the bottom cushion.
NOTICE
The seat belts must be stowed before you raise the bottom
cushion.
ÐFolding seatback (non-split
bench seat) ÐRear seats (jump seats)

19
RAISING REAR SEAT
To raise the bottom cushion, pull it up.
To lower the bottom cushion, push it down. See Luggage stowage precautionsº in
Part 2 for precautions to observe in load- ing luggage.
CAUTION!
When returning the bottom cushion
to its original position, make sure
the seat belts are not twisted or
caught under the bottom cushion
and are arranged in their proper
position for ready use.
Bench seatÐ
To raise the head restraint, pull it up.
To lower it, press the lock release but-
ton and push the head restraint down. Separate the seatÐ
To raise the head restraint, pull it up.
To lower it, press the lock release but-
ton and push the head restraint down.
To move the head restraint forward orbackward, pull it or push it.
The head restraint is most effective when
it is close to your head. Therefore, using a cushion on the seatback is not recom-mended.
CAUTION!
Adjust the top of the head restraint
so that it is closest to the top of
your ears.
After adjusting the head restraint,
make sure it is locked in position.
Do not drive with the head re-
straints removed.
Head restraints

22
Adjust the seat as needed (front seats only) and sit up straight and well back
in the seat. To fasten your belt, pull it
out of the retractor and insert the tab
into the buckle.
You will hear a click when the tab locks into the buckle.
The seat belt length automatically adjusts
to your size and the seat position.
The retractor will lock the belt during a
sudden stop or on impact. It also may lock
if you lean forward too quickly. A slow, easy motion will allow the belt to extend,
and you can move around freely. If the seat belt cannot be pulled out of the
retractor,
firmly pull the belt and release it.
You will then be able to smoothly pull the
belt out of the retractor.
When a passenger's shoulder belt is com-
pletely extended and is then retracted
even slightly, the belt is locked in that posi-
tion and cannot be extended. This feature
is used to hold the child restraint system
securely. (For details, see Child restraintº
in this chapter.) To free the belt again, fully
retract the belt and then pull the belt out
once more.CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and that the belt is not twisted.
Do not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, immediately contact
your Toyota dealer. Do not use the
seat until the seat belt is fixed. It cannot protect an adult occupant
or your child from injury.
Seat belts with an adjustable shoulder anchorÐ
Adjust the shoulder anchor position
to your size.
To raise the anchor position, push the an-
chor up. To lower the anchor position,
push the lock release button and slide the
anchor down. After the adjustment, make sure the anchor is locked in position.
ÐOutside seat belts

24
To release the belt, press the buckle-
release button and allow the belt to re- tract.
If the belt does not retract smoothly, pull
it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.Sit up straight and well back in the
seat. To fasten your belt, insert the tab
into the buckle.
You will hear a click when the tab locks into the buckle.
If the belt is not long enough for you, hold the tab at a right angle to the belt and pull
on the tab.
CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and that the belt is not twisted.
Do not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, immediately contact
your Toyota dealer. Do not use the
seat until the seat belt is fixed. It cannot protect an adult occupant
or your child from injury.
ÐCenter seat belt

27
To connect the extender to the seat
belt, insert the tab into the seat belt
buckle so that the PRESSº signs onthe buckle-release buttons of the ex-
tender and the seat belt are both facing
outward as shown.
You will hear a click when the tab locks into the buckle.
When releasing the seat belt, press on the
buckle-release button on the extender, not on the seat belt. This helps prevent
damage to the vehicle interior and extend-er itself.
When not in use, remove the extender
and store in the vehicle for future use.
CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and
that the seat belt extender is not twisted.
Do not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, immediately contact
your Toyota dealer. Do not use the
seat until the seat belt is fixed. It cannot protect an adult occupant
or your child from injury.
The SRS (Supplemental Restraint Sys-
tem) airbag is designed to provide fur-
ther protection to the driver when add-
ed to the primary protection providedby the seat belt.
In response to a severe frontal impact, the
SRS airbag works together with the seat
belt to help preventing or reduce injury byinflating, in order to decrease the likeli-
hood of the driver's head or chest directly hitting the steering wheel.
SRS airbag

34With the child restraint system installed, check that your driving position is satis-
factory and that the child restraint system
does not interfere with your driving.
If your driving position is not satisfactory, or the child restraint system interferes
with your driving, install it at
another posi-
tion. Split bench seatÐ
Adjust the passenger seat forward and
rearward travel as well as seatback posi-
tion so that the child restraint system is se-
curely restrained.
CAUTION!
Ignoring the above instructions
may result in a serious injury in case
of an accident.CAUTION!
Do not put a rear-facing child re-
straint system in the rear seat if the
child restraint system interferes
with the front seat lock mechanism
or with your proper driving posi-
tion. This can cause severe injury
to the child and front passenger in
case of sudden braking or a colli- sion.
If your driving position is not satis-
factory, install the child restraint
system at another position.
1. Run the center lap and shoulder belt
through or around the infant seat fol-
lowing the instructions provided by its
manufacturer and insert the tab into the buckle taking care not to twist the lap belt.

35
CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and
that the lap and belt is not twisted.
Do not insert coins, clips, etc. in the
buckle as this may prevent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, it cannot protect your
child from injury. Contact your To-
yota dealer immediately. Do not use
the seat until the seat belt is fixed.
2. While pressing the infant seat firmly
against the seat cushion and
seatback, tighten the lap belt by pulling
its free end to hold the infant seat
securely.
CAUTION!
Push and pull the child restraint sys-
tem is different directions to be sure
it is secure. Follow all the installa-
tion instructions provided by its
manufacturer.

37
CAUTION!
Do not put a rear-facing child re-
straint system in the rear seat if the
child restraint system interferes
with the front seat lock mechanism
or with your proper driving posi-
tion. This can cause severe injury
to the child and front passenger in
case of sudden braking or a colli- sion.
If your driving position is not satis-
factory, install the child restraint
system at another position.
1. Run the center belt through or around
the convertible seat following the in-
structions provided by its manufactur-er and insert the tab into the buckle taking care not to twist the lap belt.
CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and
that the lap belt is not twisted.
Do not insert coins, clips, etc. in the
buckle as this may prevent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, it cannot protect your
child from injury. Contact your
Toyota dealer immediately. Do not
use the seat until the seat belt isfixed.

39
(A) INFANT SEAT INSTALLATION
An infant seat is used in rear-facing
position only.CAUTION!
Do not put a rear-facing child re-
straint system in the rear seat if the
child restraint system interferes
with the front seat lock mechanism
or with your proper driving posi-
tion. This can cause severe injury
to the child and front passenger in
case of sudden braking or a colli- sion.
If your driving position is not satis-
factory, install the child restraint
system at another position.
1. Run the lap and shoulder belt through
or around the infant seat following the
instructions provided by its manufac-
turer and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
ÐInstallation with 3-point
type seat belt