low beam TOYOTA tC 2010 Owners Manual (in English)

5
Indicator symbols on the instrument cluster
Brake system warning light∗1
Driver ’s seat belt reminder light∗1
Charging system warning light∗1
Malfunction indicator lamp∗1
Low engine oil pressure warning light∗1
Anti–lock brake system warning light∗1
SRS warning light∗1
Tire pressure warning light∗1
Turn signal indicator lights Headlight high beam indicator light
Cruise control indicator light
∗2
Front passenger ’s seat belt reminder light∗1
Open door warning light∗1 ∗
1
: For details, see “Service reminder indicators and warning
buzzers” on page 107.
∗2: If this light flashes, see “Cruise control” on page 127.
Engine oil replacement reminder light∗1Automatic transmission indicator lights

94
Headlights and turn signals
HEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1—Parking, tail, license plate,
side marker and instrument panel lights
Position 2—Headlights and all of the
aboveAutomatic light cut off system
If the engine switch is turned to “LOCK”
or “ACC” position and the driver’s door is
opened with the headlight switch is on,
the light will be extinguished.
With the driver ’s door opened, turn the
ignition on or once turn the headlight
switch off and then on, the lights will turn
on. In this case, the automatic light cut off
system will not function, so the lights will
remain on. Turn off the lights if they are
not needed.
NOTICE
To prevent the battery from being dis-
charged, do not leave the lights on
longer then necessary when the en-
gine is not running.High–Low beams—
For high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)—Pull the lever all the way
back. The high beam headlights turn off
when you release the lever.
The high beam flasher works even when
the headlight switch is off.

257
—Headlights
73T024
High beam
(inside)Low beam
(outside)
1. Open the hood. Turn the bulb base
counterclockwise to the front of the
vehicle as shown.
73T006
2. Unplug the connector while depress-ing the lock release.
If the connector is tight, wiggle it.
73T007
3. Plug in a new bulb into the connec- tor and install it into the mounting
hole.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Scion dealer.

266
Fuses
81T001
Engine compartment
Fuses1. ST 7.5 A: Starting system, multiport
fuel injection system/sequential multi-
port fuel injection system
2. H–LP RH LO 10 A: Right hand head-
light (low beam)
3. H–LP LH LO 10 A: Left hand headlight
(low beam)
4. H–LP RH HI 10 A: Right hand head-
light (high beam)
5. H–LP LH HI 10 A: Left hand headlight
(high beam)
80T002
Instrument panel
6. ECU–B 10 A: Multiplex communication
system (power door lock system, illumi-
nated entry system, wireless remote
control system, back door opener, pan-
orama moonroof), air conditioning sys-
tem, gauges and meters
7. DOME 7.5 A: Interior lights, personal
lights, engine (ignition) switch light, lug-
gage compartment light
8. RAD NO.1 20 A: Audio system
9. HTR 40 A: Air conditioning system
10. ABS NO.2 40 A: Anti–lock brake sys-
tem 11. ABS NO.1 50 A:
Anti–lock brake sys-
tem
12. CDS 30 A: Electric cooling fan
13. RDI 30 A: Electric cooling fan
14. EFI 20 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system
15. OBD2 10 A: On–board diagnosis sys-
tem
16. TURN–HAZ 10 A: Turn signal lights,
emergency flashers
17. HORN 10 A: Horn
18. IGN 15 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system
19. ETCS 10 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system
20. AM2 30 A: Starting system, “IG2” and
“MET IG2” fuses
21. ALT–S 7.5 A: Charging system
22. DCC 30 A: “ECU–B”, “RAD1” and
“DOME” fuse
23. MAIN 40 A: “H–LP RH LO”, “H–LP LH
LO”, “H–LP RH HI” and “H–LP LH HI”
fuses