Temperature TOYOTA TERCEL 1996 Service Owner's Manual

A15686
A15687
DI-30
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove the lower finish panel.
(b) Connect terminals THW and E2 of ECM connector to-
gether.
HINT:
Engine coolant temperature sensor connector is disconnected.
Before checking, do a visual and contact pressure check for the
ECM connector (See page IN-26).
(c) Turn the ignition switch ON.
CHECK:
Read the temperature value on the OBD II scan tool or TOYO-
TA hand-held tester.
OK:
Temperature value: 140°C (284°F) or more
OK Open in harness between terminal E2 or termi-
nal THW, repair or replace harness.
NG
Confirm good connection at ECM.
If OK, replace ECM.
4 Check for short in harness and ECM.
PREPARATION:
(a) Disconnect the engine coolant temperature sensor con-
nector.
(b) Turn the ignition switch ON.
CHECK:
Read the temperature value on the OBD II scan tool or TOYO-
TA hand-held tester.
OK:
Temperature value: -40°C (-40°F)
OK Replace engine coolant temperature sensor.
NG

A15688
- DIAGNOSTICSENGINE
DI-31
1996 TERCEL (RM440U)
5 Check for short in harness or ECM.
PREPARATION:
(a) Remove the lower finish panel.
(b) Disconnect the E7 connector of ECM.
HINT:
The engine coolant temperature sensor connector is discon-
nected.
(c) Turn the ignition switch ON.
CHECK:
Read the temperature value on the OBD II scan tool or TOYO-
TA hand-held tester.
OK:
Temperature value: -40°C (-40°F)
OK Repair or replace harness or connector.
NG
Check and replace ECM (See page IN-26).

DI-32
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
DTC P0116 Engine Coolant Temp. Circuit Range/
Performance Problem
CIRCUIT DESCRIPTION
Refer to Engine Coolant Temp. Circuit Malfunction on page DI-28.
DTC No.DTC Detection ConditionTrouble Area
P0116
20 min. or more after the engine starts, engine coolant
temp. sensor value is 40°C (104°F) or less (2 trip detection
logic)
Engine coolant temp. sensor

Cooling system
INSPECTION PROCEDURE
HINT:
If DTC P0115 and P0116 are output Simultaneously, engine coolant temperature sensor circuit may be open.
Perform troubleshooting of DTC P0115 first.
1 Are there any other codes (besides DTC P0116) being output?
YES Go to relevant DTC chart.
NO
2 Check thermostat (See page CO-10).
NG Replace thermostat.
OK
Replace engine coolant temp. sensor.
DI1E7-08

A15693
- DIAGNOSTICSENGINE
DI-39
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Connect OBD II scan tool or TOYOTA hand-held tester and read value for volt-
age output of heated oxygen sensor.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up the engine to the normal operating temperature.
CHECK:
Read the voltage output of the heated oxygen sensor (bank 1 sensor 1) when the engine is suddenly raced.
HINT:
Perform quick racing to 4,000 rpm 3 times using accelerator pedal.
OK:
Heated oxygen sensor output a RICH signal (0.45 V or more) at least once.
OK Check and replace ECM (See page IN-26).
NG
2 Check for open and short in harness and connector between ECM and oxygen
sensor (See page IN-26).
NG Repair or replace harness or connector.

DI-42
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check for open and short in harness and connector between ECM and oxygen
sensor (See page IN-26).
NG Repair or replace harness or connector.
OK
2 Check for oxygen sensor data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the oxygen sensor output voltage and short-term fuel trim.
RESULT:
PatternOxygen sensor output voltageShort-term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about +20 %
2Rich condition (Changes at 0.4 V or more)Changes at about -20 %
3Except 1 and 2
1, 2 Check fuel trim system (See page DI-49).
3

DI-50
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check air induction system (See page MF-1).
NG Repair or replace.
OK
2 Check for heated oxygen sensor data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the oxygen sensor output voltage and short-term fuel trim.
RESULT:
PatternOxygen sensor output voltageShort-term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about + 20 %
2RIch condition (Changes at 0.4 V or more)Changes at about - 20 %
3Except 1 and 2
3 Check for oxygen sensor
(See page DI-41).
1, 2
3 Check fuel pressure (See page MF-1).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter. (See page MF-5)
OK

FI7132
Engine Speed
2,500 - 3,000 rpm
Idling
IG SW OFF
Warmed up3 min. or soCheckTime (a)(c)
(d)
(b)
FI6514
OX Signal Waveform (Oscilloscope)
1.0 V
0 V
200 m sec. /Division
DI-74
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
CONFIRMATION ENGINE RACING PATTERN
(a) Connect the TOYOTA hand-held tester to the DLC3, or connect the probe of the oscilloscope between
terminals OX1, OX2 and E1 of ECM.
(b) Start engine and warm it up with all accessories switched OFF until engine coolant temperature is
stable.
(c) Race the engine at 2,500 - 3,000 rpm for about 3 minutes.
(d) After confirming that the waveform of the oxygen sensor, bank 1 sensor 1 (OX1), oscillate around 0.5
V during feedback to the ECM, check the waveform of the heated oxygen sensor, bank 1 sensor 2
(OX2).
HINT:
If there is a malfunction in the system, the waveform of the
heated oxygen sensor, bank 1 sensor 2 (OX2), is almost the
same as that of the oxygen sensor, bank 1 sensor 1 (OX1), on
the left.
There are some cases where, even though a malfunction ex-
ists, the MIL may either light up or not light up.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P0420) being output?
YES Go to relevant DTC chart.
NO
2 Check heated oxygen sensor (bank 1 sensor 2) (See page DI-44).

DI4M5-01
Supplemental Restraint System Check Sheet
Date Problem Dist Occurred
Customer 's Name
Registration No.
Registration Year
Frame No.
Odometer Reading
Weather
Temperature
Vehicle Operation
Road Conditions
Details Of Problem
Vehicle Inspection, Repair History
Prior to Occurrence of Malfunction
(Including Supplemental Restraint
System)
Diagnosis System Inspection
SRS Warning Light
Inspection
DTC Inspection1st Time
2nd Time
1st Time
2nd TimeInspector 's
Name
Fine Cloudy Rainy Snowy Other
Approx.
Starting Idling
Driving [ Constant speed Acceleration Deceleration
Other ]
Remains ON Sometimes Light Up Does Not Light Up
Remains ON Sometimes Light Up
Does Not Light Up
Normal Code Malfunction Code
Normal Code Malfunction Code[ Code. ]
[ Code. ]km
Miles //
//
// Date Vehicle Brought In
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-147
1996 TERCEL (RM440U)
CUSTOMER PROBLEM ANALYSIS CHECK

DI4MN-01
DOOR LOCK CONTROL SYSTEM Check Sheet
Inspector 's name:
Customer 's Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading / /km
Mile
Weather Conditions
When Problem
Occurred Frequency Problem OccursWeather
Outdoor temperature
/ /

Constant
Sometimes ( Times per day, month)

Once only Brought in

Driver's door lock
control switch

Malfunction in Key Confinement Prevention Function.

Others.
Date Problem First Occurred

Fine
Cloudy
Rainy
Snowy

Various/Others

Hot
Warm
Cool

Cold (Approx. 5F ( 5C))
Problem Symptom

Driver's door

Passenger's door

Rear RH door

Rear LH door
Malfunction in Door Lock/Unlock
Operation Using Door Lock Control
Switch.

Passenger 's door lock
control switch
Driver's door

Passenger's door

Rear RH door

Rear LH door

Malfunction in Door Lock/Unlock
Operation Using Key.
Driver's door key lock
and unlock switch

Passenger 's door key
lock and unlock switch
Driver's door

Passenger's door

Rear RH door

Rear LH door

Driver's door

Passenger's door

Rear RH door

Rear LH door

Malfunction in Luggage Compartment Door Opener Function.
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-191
1996 TERCEL (RM440U)
CUSTOMER PROBLEM ANALYSIS CHECK

DI4MZ-01
THEFT DETERRENT SYSTEM Check Sheet
Inspector 's name:
Customer 's Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading / /km
Mile
Weather Conditions
When Problem
Occurred Frequency Problem OccursWeather
Outdoor temperature
/ /

Constant
Sometimes ( Times per day, month)

Once only Brought in

Theft deterrent system cannot be set.

Indicator light does not flash when the theft deterrent system is set.
(It stays on or does not light at all.)

Theft deterrent system
does not operate.
When unlocked using the
door lock knob.

When the engine hood is
opened.

System cannot be
canceled once set.
When door is unlocked using key or wireless door lock control system.

When the key is inserted in the ignition key cylinder and turned to ACC or ON
position.
(However, only when the system has never operated)

When the luggage compartment door is opened with the key.

System cannot be
canceled during warning
operation.
When door is unlocked using key or wireless door lock control system.

When the key is inserted in the ignition key cylinder and turned to ACC or ON
position.

Warning operation starts when the system is set and the door or luggage compartment door is opened with
the key.

Others.
Date Problem First Occurred

Fine
Cloudy
Rainy
Snowy

Various/Others

Hot
Warm
Cool

Cold (Approx. 5F ( 5C))
Problem Symptom
Malfunction

Horns only

Theft deterrent horn only

Headlights only

Taillights only

Starter cut only

Door lock operation only
DI-216
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
1996 TERCEL (RM440U)
CUSTOMER PROBLEM ANALYSIS CHECK