service TOYOTA TERCEL 1996 Service Manual PDF

SS0KP-02
- SERVICE SPECIFICATIONSMANUAL TRANSAXLE
SS-25
155 Author
: Date
:
1996 TERCEL (RM440U)
MANUAL TRANSAXLE
SERVICE DATA
Input shaft roller bearing journal diameterMin.24.970 mm (0.9831 in.)
Input shaft 3rd gear journal diameterMin.30.970 mm (1.2193 in.)
Input shaft 4th gear journal diameterMin.28.970 mm (1.1405 in.)
Input shaft 5th gear journal diameter (for C151)Min.24.870 mm (0.9791 in.)
Input shaft runoutMax.0.05 mm (0.0020 in.)
Output shaft roller bearing journal diameterMin.32.970 mm (1.2980 in.)
Output shaft 1st gear journal diameterMin.37.970 mm (1.4949 in.)
Output shaft 2nd gear journal diameterMin.31.970 mm (1.2587 in.)
Output shaft runoutMax.0.05 mm (0.0020 in.)
Gear thrust clearance 1st STD
Max.0.10 - 0.40 mm (0.0039 - 0.0157 in.)
0.45 mm (0.0177 in.)
Gear thrust clearance 2nd STD
Max.0.10 - 0.45 mm (0.0039 - 0.0177 in.)
0.50 mm (0.0197 in.)
Gear thrust clearance 3rd STD
Max.0.10 - 0.35 mm (0.0039 - 0.0138 in.)
0.40 mm (0.0157 in.)
Gear thrust clearance 4th STD
Max.0.10 - 0.55 mm (0.0039 - 0.0217 in.)
0.60 mm (0.0236 in.)
Gear thrust clearance 5th (for C151) STD
Max.0.10 - 0.57 mm (0.0039 - 0.0224 in.)
0.65 mm (0.0256 in.)
1st, 2nd, 3rd, 4th and 5th (for C151) gear radial clearance STD
Max.0.015 - 0.058 mm (0.0006 - 0.0023 in.)
0.070 mm (0.0028 in.)
Shift fork to hub sleeve clearance Max.1.0 mm (0.039 in.)
Synchronizer ring to gear clearance Min.0.6 mm (0.024 in.)
Drive in depth
Input shaft front oil seal
Speedometer driven gear oil seal
Control shaft cover oil seal
Select inner lever slotted spring pin
No. 1 shift inner lever slotted spring pin
No. 2 shift inner lever slotted spring pin
Transmission case oil seal
Transaxle case oil seal
15.8 ± 0.2 mm (0.622 ± 0.008 in.)
25 mm (0.98 in.)
1.0 - 2.0 mm (0.039 - 0.079 in.)
0 ± 0.5 mm (0 ± 0.020 in.)
0 ± 0.5 mm (0 ± 0.020 in.)
0 ± 0.5 mm (0 ± 0.020 in.)
2.4 ± 0.3 mm (0.094 ± 0.012 in.)
1.9 ± 0.3 mm (0.075 ± 0.012 in.)
Differential side gear backlash0.05 - 0.20 mm (0.0020 - 0.0079 in.)
Differential side gear thrust washer thickness1.50 mm (0.0591 in.)
1.55 mm (0.0610 in.)
1.60 mm (0.0630 in.)
1.65 mm (0.0650 in.)
1.70 mm (0.0669 in.)
1.75 mm (0.0689 in.)
Differential side bearing preload (at starting) (for use with SST)
New bearing
Reused bearing
0.8 - 1.6 N´m (8 - 16 kgf´cm, 6.9 - 13.9 in.´lbf)
0.5 - 1.0 N´m (5 - 10 kgf´cm, 4.3 - 8.7 in.´lbf)

SS-26
- SERVICE SPECIFICATIONSMANUAL TRANSAXLE
156 Author
: Date
:
1996 TERCEL (RM440U) Input shaft snap ring thickness
No. 2 clutch hub Mark 0
1
2
3
4
5
No. 3 clutch hub (for C151) Mark A
B
C
D
E
F
G
Input shaft rear bearing Mark A
B
C
D
E
F
2.30 mm (0.0906 in.)
2.36 mm (0.0929 in.)
2.42 mm (0.0953 in.)
2.48 mm (0.0976 in.)
2.54 mm (0.1000 in.)
2.60 mm (0.1024 in.)
2.25 mm (0.0886 in.)
2.31 mm (0.0909 in.)
2.37 mm (0.0933 in.)
2.43 mm (0.0957 in.)
2.49 mm (0.0980 in.)
2.55 mm (0.1004 in.)
2.61 mm (0.1028 in.)
2.29 mm (0.0902 in.)
2.35 mm (0.0925 in.)
2.41 mm (0.0949 in.)
2.47 mm (0.0972 in.)
2.53 mm (0.0996 in.)
2.59 mm (0.1020 in.)
Output shaft snap ring thickness
No. 1 clutch hub Mark A
B
C
D
E
F
2.50 mm (0.0984 in.)
2.56 mm (0.1008 in.)
2.62 mm (0.1031 in.)
2.68 mm (0.1055 in.)
2.74 mm (0.1079 in.)
2.80 mm (0.1102 in.)
Differential side bearing adjusting shim thickness Mark A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U2.10 mm (0.0827 in.)
2.15 mm (0.0846 in.)
2.20 mm (0.0866 in.)
2.25 mm (0.0886 in.)
2.30 mm (0.0906 in.)
2.35 mm (0.0925 in.)
2.40 mm (0.0945 in.)
2.45 mm (0.0965 in.)
2.50 mm (0.0984 in.)
2.55 mm (0.1004 in.)
2.60 mm (0.1024 in.)
2.65 mm (0.1043 in.)
2.70 mm (0.1063 in.)
2.75 mm (0.1083 in.)
2.80 mm (0.1102 in.)
2.85 mm (0.1122 in.)
2.90 mm (0.1142 in.)
2.95 mm (0.1161 in.)
3.00 mm (0.1181 in.)

SS0KQ-04
- SERVICE SPECIFICATIONSMANUAL TRANSAXLE
SS-27
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head
10 mm head64
46
7.4650
470
7547
34
65 in.´lbf
Engine left mounting bracket x Insulator4849036
Engine rear mounting insulator x Body7880058
Engine rear mounting insulator x Bracket B bolt
C bolt64
90650
92047
67
Front exhaust pipe clamp set bolt1919014
Front exhaust pipe x Exhaust manifold6263046
Starter x Transaxle3940029
Clutch release cylinder x Transaxle121209
Shift lever assembly x Body121209
Grommet retainer x Body4.95043 in.´lbf
Retainer x Body4.95043 in.´lbf
Output shaft front bearing lock plate set bolt1111 58
Transmission case x Transaxle case2930022
Reverse shift arm bracket1717513
Straight screw plug (Reverse restrict pin) (C151)
Straight screw plug13
13130
1309
9
Straight screw plug (Shift fork shaft)2525018
Straight screw plug (Lock ball assembly) (C151)
Straight screw plug (C141)39
39400
40029
29
Reverse idler gear shaft lock bolt2930022
Rear bearing retainer2728020
Output shaft lock nut11 81,20087
Shift fork and shift head x Shift fork shaft1616012
Shift and select lever assembly2020014
Transmission case x Transmission case cover1818513
Back-up light switch4041030
Filler and drain plugs3940029
Ring gear x Differential case1241,26091
Speedometer driven gear1111 58
Control lever housing support bracket x Transmission case1111 58
Selecting bellcrank assembly x Transmission case2525018
Shift and select lever shaft assembly lock bolt2930022
Transaxle case receiver x Transaxle case1111 58
No. 1 and No. 2 oil receiver pipe1717513

SS0LK-02
SS-28
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
158 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A132L)
SERVICE DATA
Governor pressure Vehicle speed reference
30 km/h (19 mph)
60 km/h (37 mph)
90 km/h (56 mph)
59 - 137 kPa (0.6 - 1.4 kgf/cm2, 9 - 20 psi)
186 - 265 kPa (1.9 - 2.7 kgf/cm2, 27 - 38 psi)
353 - 431 kPa (3.6 - 4.4 kgf/cm2, 51 - 63 psi)
Line pressure (Wheel locked)
Engine Idling D position
R position
AT stall (Throttle valve fully opened) D position
R position
363 - 422 kPa (3.7 - 4.3 kgf/cm2, 53 - 61 psi)
530 - 706 kPa (5.4 - 7.2 kgf/cm2, 77 - 102 psi)
902 - 1,049 kPa (9.2 - 10.7 kgf/cm2, 131 - 152 psi)
1,412 - 1,647 kPa (14.4 - 16.8 kgf/cm2, 205 - 239 psi)
Engine stall revolution D and R positions2,300 ± 200 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF) N position750 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)
Between boot end face and inner cable stopper
0 - 1 mm (0 - 0.04 in.)
Torque converter clutch installation distance
Drive plate runoutMax.
Torque converter clutch runout Max.More than 13.0 mm (0.512 in.)
0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
Differential oil seal drive in depth0 ± 0.5 mm (0 ± 0.020 in.)
Speedometer driven gear oil seal drive in depth19 mm (0.75 in.)
Shift Point
D position
Throttle valve fully opened 1 "2
2 " 3
3 " 2
2 " 1
L position
Throttle valve fully closed 2 " 1
47 - 62 km/h (29 - 39 mph)
91 - 107 km/h (57 - 66 mph)
85 - 104 km/h (53 - 65 mph)
36 - 46 km/h (22 - 29 mph)
39 - 49 km/h (24 - 30 mph)
Lock-up point
D position
Throttle valve fully closed Lock-up ON
Lock-up OFF
63 - 72 km/h (39 - 45 mph)
59 - 68 km/h (37 - 42 mph)

SS0LL-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
SS-29
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug4950036
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C
Bolt D7.4
25
46
6475
250
470
65065 in.´lbf
18
34
47
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

SS0LI-04
SS-30
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
160 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A242L)
SERVICE DATA
Governor pressure Vehicle speed reference
30 km/h (19 mph)
60 km/h (37 mph)
90 km/h (56 mph)
59 - 137 kPa (0.6 - 1.4 kgf/cm2, 9 - 20 psi)
196 - 275 kPa (2.0 - 2.8 kgf/cm2, 28 - 40 psi)
363 - 441 kPa (3.7 - 4.5 kgf/cm2, 53 - 64 psi)
Line pressure (Wheel locked)
Engine Idling D position
R position
AT stall (Throttle valve fully opened) D position
R position
373 - 422 kPa (3.8 - 4.3 kgf/cm2, 54 - 61 psi)
549 - 706 kPa (5.6 - 7.2 kgf/cm2, 80 - 102 psi)
902 - 1,049 kPa (9.2 - 10.7 kgf/cm2, 131 - 152 psi)
1,638 - 1,902 kPa (16.7 - 19.4 kgf/cm2, 238 - 276 psi)
Engine stall revolution D and R positions2,300 ± 200 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF) N position750 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)
Between boot end face and inner cable stopper
0 - 1 mm (0 - 0.04 in.)
Torque converter clutch installation distance
Drive plate runoutMax.
Torque converter clutch runout Max.More than 13.0 mm (0.512 in.)
0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
Differential oil seal drive in depth LH side
RH side5.3 ± 0.5 mm (0.209 ± 0.020 in.)
3.1 ± 0.5 mm (0.122 ± 0.020 in.)
Speedometer driven gear oil seal drive in depth25.0 mm (0.98 in.)
Shift Point
D position
Throttle valve fully opened 1 "2
2 " 3
3 " 2
2 " 1
Throttle valve fully closed 3 O/D
L position
Throttle valve fully closed 2 " 1
45 - 61 km/h (28 - 38 mph)
89 - 106 km/h (55 - 66 mph)
83 - 102 km/h (52 - 63 mph)
83 - 43 km/h (19 - 27 mph)
19 - 33 km/h (12 - 21 mph)
44 - 56 km/h (27 - 35 mph)
Lock-up point
D position
Throttle valve fully closed Lock-up ON
Lock-up OFF
65 - 76 km/h (40 - 47 mph)
61 - 72 km/h (38 - 45 mph)

SS0LJ-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
SS-31
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug1717513
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C7.4
64
4675
650
47065 in.´lbf
47
34
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

SS0LO-07
SS-32
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
162 Author
: Date
:
1996 TERCEL (RM440U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire inflationTire sizeCold tire inflation
pressure
Tire size
155SR13 ASFront240 kPa (2.4 kgf/cm2, 34 psi)ressure 155SR13 AS Front
Rear
240 kPa (2.4 kgf/cm, 34 si)
225 kPa (2.25 kgf/cm2, 32 psi)
Vehicle heightTire size
155SR13 ASFront
Rear
187.9 mm (7.40 in.)
253.2 mm (9.97 in.)
Front wheel align-
mentToe-in (Total)
Tie rod end left-right error0.1° ± 0.2° (1 ± 2 mm, 0.04 ± 0.08 in.)
1.5 mm (0.059 in.) or less
ment
Camber
Left-right error-0°20' ± 45'
45' or less
Caster
Left-right error1°20' ± 45'
45' or less
Steering axis inclination
Left-right error12°10' ± 45'
45' or less
Wheel angle Inside wheel
Outside wheel35°55' ± 2°
32°10' (Reference)
Rear wheel align-Toe-in (Total)0.3° ± 0.3° (3 ± 3 mm, 0.12 ± 0.12 in.)Rear wheel align-
ment
Camber
Left-right error-0°30' ± 45'
45' or less
Front axleAxle bearing backlash0.05 mm (0.0020 in.) or lessFront axle
Axle hub deviation0.05 mm (0.0020 in.) or less
Front suspensionLower ball joint turning torque0.8 - 2.5 N´m (8 - 25 kgf´cm, 7 - 22 in.´lbf)
Rear axleBearing preload (turning)Add frictional force plus 0 - 11.8 N (0 - 1.2 kgf, 0 - 2.6 lbf)Rear axle
Axle hub axial play0.05 mm (0.0020 in.) or less

SS0LP-06
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-33
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT:
Disc brake dust cover x Steering knuckle8.38574 in.´lbf
Lower ball joint x Steering knuckle981,00072
Steering knuckle x Shock absorber2452,500181
Lower ball joint x Lower suspension arm8082059
Tie rod end lock nut4748035
Tie rod end x Steering knuckle4950036
Disc brake caliper x Steering knuckle8890065
Drive shaft lock nut2162,200159
Piston rod x Suspension support4747534
Suspension support x Body3940029
Flexible hose x Shock absorber2930022
Lower suspension arm x BodyFront side1421,450105Lower sus ension arm x Body Front side
Rear side
142
74
1,450
750
105
55
Hub nut1031,05076
ABS speed sensor x Steering knuckle7.88069 in.´lbf
REAR:
Piston rod x Suspension support3435025
Suspension support x Body3940029
Shock absorber x Axle beam6869050
Backing plate x Axle beam7071051
Parking brake cable x Backing plate7.88069 in.´lbf
Brake line x Wheel cylinder1515511
Body x Axle beam1421,450105
Lateral control rod x Axle beam8385061
Lateral control rod x Body11 31,15083
ABS speed sensor x Axle beam7.88069 in.´lbf
ABS speed sensor wire x Axle beam5.45548 in.´lbf

SS0M2-1 1
SS-34
- SERVICE SPECIFICATIONSBRAKE
164 Author
: Date
:
1996 TERCEL (RM440U)
BRAKE
SERVICE DATA
Brake pedal height (from asphalt sheet) EZ grade143.0 - 153.0 mm (5.63 - 6.02 in.)Brake edal height (from as halt sheet) EZ grade
Except EZ grade
143.0 153.0 mm (5.63 6.02 in.)
140.0 - 150.0 mm (5.51 - 5.91 in.)
Brake pedal freeplay1 - 6 mm (0.04 - 0.24 in.)
Brake pedal reserve distance at 490 N (50 kgf, 110.2 lbf) w/o ABSMore than 60 mm (2.36 in.)Brake edal reserve distance at 490 N (50 kgf, 11 0.2 lbf) w/o ABS
w/ ABS
More than 60 mm (2.36 in.)
More than 55 mm (2.17 in.)
Brake booster push rod to piston clearance (w/ SST)0 mm (0 in.)
Front brake pad thickness STD10.0 mm (0.394 in.)Front brake ad thickness STD
Minimum
10.0 mm (0.394 in.)
1.0 mm (0.039 in.)
Front brake disc thickness STD18.0 mm (0.709 in.)Front brake disc thickness STD
Minimum
18.0 mm (0.709 in.)
17.0 mm (0.669 in.)
Front brake disc runout Maximum0.07 mm (0.0028 in.)
Rear brake drum inside diameter STD180 mm (7.087 in.)Rear brake drum inside diameter STD
Maximum
180 mm (7.087 in.)
181 mm (7.126 in.)
Rear brake lining thickness STD4.0 mm (0.157 in.)Rear brake lining thickness STD
Minimum
4.0 mm (0.157 in.)
1.0 mm (0.039 in.)
Rear brake drum to shoe clearance0.6 mm (0.024 in.)
Parking brake lever travel at 196 N (20 kgf, 44.1 lbf)5 - 8 clicks