light TOYOTA TERCEL 1996 Service Manual Online

P03849
Overall Length
EM0255
P20367
45° Carbide Cutter
Z07819
Width
Z08336
45°
1.0 - 1.4 mm30° EM-34
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
(d) Check the valve overall length.
Standard overall length:
Intake93.45 mm (3.6791 in.)
Exhaust93.89 mm (3.6768 in.)
Minimum overall length:
Intake92.95 mm (3.6594 in.)
Exhaust93.39 mm (3.6768 in.)
If the overall length is less than minimum, replace the valve.
(e) Check the surface of the valve stem tip for wear.
If the valve stem tip is worn, resurface the tip with a grinder or
replace the valve.
NOTICE:
Do not grind off more than minimum.
7. INSPECT AND CLEAN VALVE SEATS
(a) Using a 45° carbide cutter, resurface the valve seats.
Remove only enough metal to clean the seats.
(b) Check the valve seating position.
(c) Apply a light coat of prussian blue (or white lead) to the
valve face. Lightly press the valve against the seat. Do not
rotate valve.
(d) Check the valve face and seat for the following:
(1) If blue appears 360° around the face, the valve is
concentric. If not, replace the valve.
(2) If blue appears 360° around the valve seat, the
guide and face are concentric. If not, resurface the
seat.
(3) Check that the seat contact is in the middle of the
valve face with the following width:
1.0 - 1.4 mm (0.039 - 0.055 in.)
If not, correct the valve seats as follows:
(1) If the seating is too high on the valve face, use 30°
and 45° cutters to correct the seat.

Z14254
Painted
Black Painted Silver Intake Exhaust
P20416
SST
EM9933
- ENGINE MECHANICALCYLINDER HEAD
EM-43
1996 TERCEL (RM440U)
HINT:
The intake valve oil seal is silver and the exhaust valve oil seal
is black.
(b) Install the valve.
(c) Install the spring seat.
(d) Install the valve spring.
(e) Install the spring retainer.
(f) Using SST, compress the valve spring and place the 2
keepers around the valve stem.
SST 09202-70010
(g) Using a plastic-faced hammer, lightly tap the valve stem
tip to assure proper fit.
3. INSTALL VALVE LIFTERS AND SHIMS
(a) Install the valve lifter and shim.
(b) Check that the valve lifter rotates smoothly by hand.
4. INSTALL STUD BOLT FOR CYLINDER HEAD COVER
5. INSTALL NO.2 ENGINE HANGER
Torque:
No. 1
21 N´m (210 kgf´cm, 15 ft´lbf)
No. 2
53 N´m (530 kgf´cm, 38 ft´lbf)

P20389
Gasket
EM1OG-01
P20419
EX
(A)
Bi-Hexagon Wrench
(B)IN
(B)
(A)(B)
(B)(B)
(B)
8
61 3
9
10 4 257
(A) (A) (A)(A) IN
EX
P20413
Painted Mark
90°
P20174
(b)(c)
(d)(e)
EM-44
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
INSTALLATION
1. PLACE CYLINDER HEAD ON CYLINDER BLOCK
(a) Place a new cylinder head gasket in position on the cylin-
der block.
NOTICE:
Be careful of the installation direction.
(b) Place the cylinder head in position on the cylinder head
gasket.
2. INSTALL CYLINDER HEAD BOLTS
HINT:

The cylinder head bolts are tightened in 2 progressive
steps (steps (b) and (d)).

If any cylinder head bolt is broken or deformed, replace
it.

There are 2 lengths of cylinder head bolts, long (A) and
short (B).
(a) Apply a light coat of engine oil on the threads and under
the heads of the cylinder head bolts.
(b) First, using a bi-hexagon wrench 8 mm, install and uni-
formly tighten the 10 cylinder head bolts, in several
passes, in the sequence shown.
Torque: 45 N´m (450 kgf´cm, 33 ft´lbf)
If any one of the cylinder head bolts does not meet the torque
specification, replace the cylinder head bolt.
(c) Mark the front of the cylinder head bolt head with paint.
(d) Retighten the cylinder head bolts 90° in the numerical or-
der shown.
(e) Check that the painted mark is now at a 90° angle to front.
3. ASSEMBLE INTAKE CAMSHAFT
(a) Mount the hexagonal wrench head portion of the cam-
shaft in a vise.
NOTICE:
Be careful not to damage the camshaft.
(b) Install the camshaft gear spring.
(c) Install the camshaft sub-gear.
(d) Install the wave washer.
HINT:
Align the pins on the gears with the gear spring ends.

EG0010
Timing Mark
P20369
Timing Mark
EXIN
Other Timing Mark
P20377
8
6
13 4
2
57
P20248
Seal Packing EM-46
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
(e) Apply engine oil to thrust portion of the exhaust camshaft.
(f) Engage the exhaust camshaft gear to the intake cam-
shaft gear by matching the timing marks on each gear.
NOTICE:
There are also assembly reference marks on each gear as
shown in the illustration. Do not use these marks.
(g) Roll down the exhaust camshaft onto the bearing journals
while engaging gears with each other.
HINT:
The above angle allows the No.2 and No.4 cylinder cam lobes
of the exhaust camshaft to push their valve lifters evenly.
(h) Lightly push the exhaust camshaft gear without applying
excessive force.
(i) Install the 4 bearing caps in their proper locations.
(j) Temporarily tighten the bearing cap bolts uniformly and
alternately, in several passes, in the sequence shown un-
til the bearing caps are snug with the cylinder head.
(k) Remove the service bolt.
(l) Clean the installed surfaces of the No.2 bearing cap and
cylinder head with cleaner.
(m) Apply seal packing to the No.2 bearing cap as shown.
Seal packing:
Part No. 08826-00080 or equivalent

P20948
P20953
Timing Mark
Installation
Mark
P20746
P20748
P20749
- ENGINE MECHANICALCYLINDER HEAD
EM-49
1996 TERCEL (RM440U)
8. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with timing
mark º0º of the No.1 timing belt cover.
(b) Turn the camshaft, and align the hole of the camshaft tim-
ing pulley on the side with the 5E mark with the timing
mark of the bearing cap.
9. INSTALL TIMING BELT
(a) Starting from the right hand side of the pulley and instal-
ling the belt counterclockwise.
(b) Loosen the No.1 idler pulley mounting bolt until the pulley
is moved slightly by the spring tension.
(c) Turn the crankshaft pulley 2 revolutions from TDC to TDC.
NOTICE:
Always turn the crankshaft clockwise.

P20565
M/T EM-58
- ENGINE MECHANICALENGINE UNIT
1996 TERCEL (RM440U)

Engine coolant temperature sender gauge connec-
tor

Engine coolant temperature sensor connector

Camshaft position sensor connector

EGR VSV

Fan engine coolant temperature switch connector

A/T only:
Lock-up solenoid connector

A/T only:
Park/Neutral position switch connector

M/T only:
Backup light switch connector

A/T only:
No.2 vehicle speed sensor connector

Ground strap

Throttle position sensor connector

IAC valve connector

Injector connectors

Crankshaft position sensor connector

Knock sensor connector

Starter connector and wire

Generator connector and wire
15. M/T only:
REMOVE CLUTCH RELEASE CYLINDER WITHOUT
DISCONNECTING TUBE
(a) Remove the 3 bolts, release cylinder and tube from the
transaxle.
(b) Disconnect the ground strap.
16. M/T:
DISCONNECT CONTROL CABLE(S) FROM TRANS-
AXLE
(a) Remove the clip and plate washer.
(b) Remove the retainer from the cable.

EM-66
- ENGINE MECHANICALENGINE UNIT
1996 TERCEL (RM440U)
15. CONNECT ENGINE WIRE HARNESS
Connect these connectors and wires:

Main heated oxygen sensor connector

Oil pressure switch connector

Engine coolant temperature sender gauge
connector

Engine coolant temperature sensor connector

Camshaft position sensor connector

EGR VSV

Fan engine coolant temperature switch connector

A/T only:
Lock-up solenoid connector

A/T only:
Park/Neutral position switch connector

M/T only:
Backup light switch connector

A/T only:
No.2 vehicle speed sensor connector

Ground strap

Throttle position sensor connector

IAC valve connector

Injector connectors

Crankshaft position sensor connector

Knock sensor connector

Starter connector and wire

Generator connector and wire
16. w/ PS:
CONNECT IDLE-UP AIR HOSES TO AIR CONTROL
VA LV E
17. CONNECT SPEEDOMETER CABLE
18. CONNECT HOSES
(a) Connect the brake booster vacuum hose.
(b) Connect the MAP sensor hose.
(c) Connect the heater hoses.

EM9988
EM3441
P20487
EM9392
EM3444
- ENGINE MECHANICALCYLINDER BLOCK
EM-71
1996 TERCEL (RM440U)
16. REMOVE REAR OIL SEAL RETAINER
(a) Remove the 4 bolts.
(b) Using a screwdriver, remove the oil seal retainer by prying
the portions between the oil seal retainer and main bear-
ing cap.
17. CHECK CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while mov-
ing the rod back and forth.
Standard thrust clearance:
0.15 - 0.35 mm (0.0059 - 0.0138 in.)
Maximum thrust clearance:
0.45 mm (0.0177 in.)
If the thrust clearance is greater than maximum, replace the
connecting rod assembly. If necessary, replace the crankshaft.
18. REMOVE CONNECTING ROD CAPS AND CHECK OIL
CLEARANCE
(a) Check the matchmarks on the connecting rod and cap to
ensure correct reassembly.
(b) Remove the 2 connecting rod cap nuts.
(c) Using a soft-faced hammer, lightly tap the connecting rod
bolt and lift the cap and lower bearing.
HINT:
Keep the lower bearing inserted with the connecting rod cap.

P20551
P20530
Front
Z14291
1
2 3
45
6
7
89
10
EM3480
P20569
Front Mark
(Cavity)
FrontPush
- ENGINE MECHANICALCYLINDER BLOCK
EM-87
1996 TERCEL (RM440U)
7. INSTALL MAIN BEARING CAPS AND LOWER
THRUST WASHERS
(a) Install the 2 thrust washers on the No.3 bearing cap with
the oil grooves facing outward.
(b) Install the 5 main bearing caps in their proper locations.
HINT:
Each bearing cap has a number and front mark.
(c) Apply a light coat of engine oil on the threads and under
the heads of the main bearing caps.
(d) Install and uniformly tighten the 10 bolts of the main bear-
ing caps, in several passes, in the sequence shown.
Torque: 58 N´m (580 kgf´cm, 42 ft´lbf)
(e) Check that the crankshaft turns smoothly.
(f) Check the crankshaft thrust clearance (See page
EM-70).
8. INSTALL PISTON AND CONNECTING ROD AS-
SEMBLIES
(a) Cover the connecting rod bolts with a short piece of hose
to protect the crankshaft from damage.
(b) Using a piston ring compressor, push the correctly num-
bered piston and connecting rod assemblies into each
cylinder with the front mark of the piston facing forward.

EM3481
Front Mark
(Protrusion)
Front
EM3448
P20475
Seal Packing
A'B'
A
B
A - A' B - B' EM-88
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
9. INSTALL CONNECTING ROD CAPS
(a) Match the numbered connecting rod cap with the num-
bered connecting rod.
(b) Install the connecting rod cap with the front mark facing
forward.
(c) Apply a light coat of engine oil on the threads and under
the nuts of the connecting rod cap.
(d) Install and alternately tighten the nuts of the connecting
rod cap in several passes.
Torque: 40 N´m (400 kgf´cm, 29 ft´lbf)
(e) Check that the crankshaft turns smoothly.
(f) Check the connecting rod thrust clearance (See page
EM-70).
10. INSTALL REAR OIL SEAL RETAINER
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the rear oil
seal retainer and cylinder block.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing groove.
Thoroughly clean all components to remove all the
loose material.
Using a non-residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the rear oil seal retainer as shown
in the illustration.
Seal packing:
Part No. 08826-00080 or equivalent
Install a nozzle that has been cut to a 2 - 3 mm (0.08
- 0.12 in.) opening.
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.