light TOYOTA TERCEL 1996 Service Owners Manual

P20175
New
Gasket
FI1654
Fulcrum Length
SST
30 cm
FI4295
CORRECT
WRONG
WRONG Delivery Pipe O-Ring
Grommet
Injector
FI4296
Delivery
Pipe
O-Ring
Grommet
InjectorCylinder Head
- MFIMFI SYSTEM
MF-3
527 Author
: Date
:
1996 TERCEL (RM440U)
(b) When connecting the union bolt on the high pressure pipe
union, observe these procedures:
(1) Always use 2 new gaskets.
(2) Tighten the union bolt by hand.
(3) Tighten the union bolt to the specified torque.
Torque: 29.0 N´m (290 kgf´cm, 22 ft´lbf)
(c) When connecting the flare nut on the high pressure pipe
union, observe these procedures:
(1) Apply a light coat of engine oil to the flare nut, and
tighten the flare nut by hand.
(2) Using SST, tighten the flare nut to specified torque.
SST 09631-22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque: 30 N´m (300 kgf´cm, 23 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(d) Observe these precautions when removing and installing
the injectors.
(1) Never reuse the O-ring.
(2) When placing a new O-ring on the injector, take
care not to damage it in any way.
(3) Coat a new O-ring with spindle oil or gasoline be-
fore installing-never use engine, gear or brake oil.
(e) Install the injector in the delivery pipe and cylinder head
as shown in the illustration.

SF1PU-02
- MFIFUEL PRESSURE REGULATOR
MF-15
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL FUEL PRESSURE REGULATOR
(a) Apply a light coat of gasoline to a new O-ring, and install
it to the pressure regulator.
(b) Attach the pressure regulator to the delivery pipe.
(c) Check that the pressure regulator rotates smothly.
NOTICE:
If it does not rotate smothly, the O-ring may be pinched, so
remove the pressure regulator and perform again steps (b)
and (c) above.
(d) Install the pressure regulator with the 3 bolts.
Torque:8.0 N´m (80kgf´cm, 69 in.´lbf)
2. CONNECT FUEL RETURN HOSE TO FUEL PRES-
SURE REGULATOR
3. CONNECT VACUUM SENSING HOSE TO FUEL PRES-
SURE REGULATOR
4. CHECK FOR FUEL LEAKS (See page MF-1)

SF0X4-05
FI3271
New
O-Ring
New Grommet
P00159
CORRECT
WRONG
InjectorDelivery Pipe GrommetO-Ring
WRONG
P20295
Spacer
Insulator
Connector MF-22
- MFIINJECTOR
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL INJECTORS AND DELIVERY PIPE
(a) Install a new grommet to the injector.
(b) Apply a light coat of gasoline to an O-ring, and install it
to the injector.
(c) While turning the injector left and right, install it to the de-
livery pipe. Install the 4 injectors.
(d) Place the 2 spacers and 4 insulators in position on the cyl-
inder head.
(e) Place the injectors together with the delivery pipe on the
cylinder head.
(f) Check that the injectors rotate smoothly.
HINT:
If the injectors do not rotate smoothly, the probable cause is in-
correct installation of O-rings. Replace the O-rings.
(g) Position the injector connector upward.
(h) Install the 2 bolts.
Torque: 19 N´m (190 kgf´cm, 14 ft´lbf)
2. CONNECT ENGINE WIRE
(a) Connect the 4 injector connectors.
(b) Connect the engine wire to the surge tank stay.
3. CONNECT FUEL INLET HOSE TO DELIVERY PIPE
(a) Install 2 new gaskets and the inlet hose with the union
bolt.
Torque: 30 N´m (300 kgf´cm, 23 ft´lbf)
(b) Connect the engine wire clamp to the No.2 engine hang-
er.
4. CONNECT FUEL RETURN HOSE TO FUEL RETURN
PIPE
5. CONNECT VACUUM SENSING HOSE TO FUEL PRES-
SURE REGULATOR

CO18B-01
CO1205
Dimension B
Stopper Bolt
Overhaul HandlePart A
ClawSST
P21090
Lock
Plate
Stopper BoltTank
P21091
CO-18
- COOLINGRADIATOR
1996 TERCEL (RM440U)
DISASSEMBLY
1. ASSEMBLE SST
SST 09230-01010
(a) Install the claw to the overhaul handle, inserting it in the
hole in part A as shown in the diagram.
(b) While gripping the handle, adjust the stopper bolt so that
dimension B is as shown in the diagram is 0.2 - 0.5 mm
(0.008 - 0.020 in.).
NOTICE:
If this adjustment is not performed, the claw may be dam-
aged.
2. UNCAULK LOCK PLATES
Using SST to release the caulking, squeeze the handle until
stopped by the stopper bolt.
SST 09230-01010
3. REMOVE TANKS AND O-RINGS
Lightly tap the radiator hose inlet (or outlet) with a soft-faced
hammer, and remove the tank.
Remove the O-ring.
4. A/T:
REMOVE OIL COOLER FROM LOWER TANK
(a) Remove the 2 nuts, spring washers, plate washers and oil
cooler.
(b) Remove the O-ring from the oil cooler.

CO0Y3-02
P21092
A
B
C
CO1267
Lock PlateLock Plate
Core
N00305
CORRECTWRONG
WRONG
P21093
CORRECT
WRONGTank
Lock
Plate
- COOLINGRADIATOR
CO-19
1996 TERCEL (RM440U)
REASSEMBLY
1. A/T:
INSTALL OIL COOLER TO LOWER TANK
(a) Clean the O-ring contact surface of the lower tank and oil
cooler.
(b) Install new O rings to the oil cooler.
(c) Install the oil cooler with the O-rings to the lower tank.
(d) Install the plate washers, spring washers and nuts.
Torque:
Nut A: 15 N´m (150 kgf´cm, 11 ft´lbf)
Nut B and C: 8.5 N´m (85 kgf´cm, 75 in.´lbf)
2. INSPECT LOCK PLATE
Inspect the lock plate for damage.
HINT:

If the sides of the lock plate groove are deformed, reas-
sembly of the tank will be impossible.

Therefore, first correct any deformation with pliers or like
object. Water leakage will result if the bottom of the lock
plate groove is damaged or dented or dented. There fore,
repair or replace if necessary.
3. INSTALL NEW O-RINGS AND TANKS
(a) After checking that there are no foreign objects in the lock
plate groove, install a new O-ring without twisting it.
HINT:
When cleaning the lock plate groove, lightly rub it with sand pa-
per without scratching it.
(b) Install the tank without damaging the O-ring.
(c) Tap the lock plate with a soft-faced hammer so that there
is no gap between it and the tank.

CO1206
Dimension B
Punch Assembly
Overhaul HandleStopper BoltPartSST
P21094
8 7
65
43
2
1
P21095
Stopper
BoltSSTTank
Lock
Plate
P21096
RibBracket
Claw
Z15037
CO-20
- COOLINGRADIATOR
1996 TERCEL (RM440U)
4. ASSEMBLE SST
SST 09230-01010
(a) Install the punch assembly to the overhaul handle, insert-
ing it in the hole in part A as shown in the illustration.
(b) While gripping the handle, adjust the stopper bolt so that
dimension B shown in the diagram is 7.7 mm (0.30 in.)
5. CAULK LOCK PLATE
(a) Lightly press SST against the lock plate in the order
shown in the illustration. After repeating this a few times,
fully caulk the lock plate by squeezing the handle until
stopped by the stopper plate.
SST 09230-01010
HINT:

Do not stake the areas protruding around the ports,brack-
et or tank ribs.

The oil cooler (A/T only) and the points attowed in the il-
lustlation cannot be staked with the SST. Use a plier or like
object and be careful not to damage the core plates.

P20908
CORRECT
WRONG
S06255
P21178
Ohmmeter
S06256
Push
P04690
CORRECT
WRONG IG-2
- IGNITIONIGNITION SYSTEM
633 Author
: Date
:
1996 TERCEL (RM440U)
2. INSPECT HIGH-TENSION CORDS
(a) Disconnect the high-tension cords from the spark plugs.
(1) Disconnect the high-tension cords at the rubber
boot. Do not pull on the cords.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside.
(2) Disconnect the high-tension cords from the clamp.
(b) Disconnect the high-tension cords from the ignition coils.
(1) Using a screwdriver, lift up the lock claw and discon-
nect the holder from the ignition coils.
(2) Disconnect the high-tension cord at the grommet.
(3) Do not pull on the cord.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside. Do not wipe any of the oil from the grommet after the
high-tension cord is disconnected.
(c) Reconnect the high-tension cords to the ignition coils.
Maximum resistance: 25 kW per cord
If the resistance is greater than maximum, check the terminals.
If necessary, replace the high-tension cord.
(d) Reinstall the high-tension cords.
(1) Assemble the holder and grommet.
(2) Align the spline of the ignition coil with the spline of
the holder, and push in the cord.
NOTICE:
Check that the holder is correctly installed to the grommet
and distributor cap as shown in the illustration.
(3) Check that the lock claw of the holder is engaged by
lightly pulling the holder.
(4) Connect the high-tension cords to the clamp.
(e) Reconnect high-tension cords to spark plugs.

N00280
DENSO
Borroughs
CH0087
CORRECTWRONG WRONG
P13685
CH0732
Disconnect Wire
from Terminal B
Generator
Voltmeter BatteryAmmeter
B
- CHARGINGCHARGING SYSTEM
CH-3
1996 TERCEL (RM440U)
(b) Using a belt tension gauge, check the drive belt tension.
Belt tension gauge:
DENSO BTG-20 (95506-00020)
Borroughs No. BT-33-73F
Drive belt tension:
New belt
Used belt160 ± 20 lbf
100 ± 20 lbf
If the belt tension is not as specified, adjust it.
HINT:

ºNew beltº refers to a belt which has been used less than
5 minutes on a running engine.

ºUsed beltº refers to a belt which has been used on a run-
ning engine for 5 minutes or more.

After installing a belt, check that it fits properly in the
ribbed grooved.

Check by hand to confirm that the belt has not slipped out
of the groove on the bottom of the pulley.

After installing a new belt, run the engine for about 5 min-
utes and recheck the belt tension.
4. VISUALLY CHECK GENERATOR WIRING AND
LISTEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) Check that there is no abnormal noise from the generator
while the engine is running.
5. INSPECT CHARGE WARNING LIGHT CIRCUIT
(a) Warm up the engine and then turn it off.
(b) Turn off all accessories.
(c) Turn the ignition switch ºONº. Check that the charge warn-
ing light is lit.
(d) Start the engine. Check that the light goes off.
If the light does not go off as specified, troubleshoot the charge
light circuit.
6. INSPECT CHARGING CIRCUIT WITHOUT LOAD
HINT:
If a battery/generator tester is available, connect the tester to
the charging circuit as per manufacturer's instructions.
(a) If a tester is not available, connect a voltmeter and amme-
ter to the charging circuit as follows:

Disconnect the wire from terminal B of the generator
and connect it to the negative (-) tester probe of the
ammeter.

P13734
Terminal F CH-4
- CHARGINGCHARGING SYSTEM
1996 TERCEL (RM440U)

Connect the positive (+) tester probe of the amme-
ter to terminal B of the generator.

Connect the positive (+) tester probe of the voltme-
ter to terminal B of the generator.

Ground the negative (-) tester probe of the voltme-
ter.
(b) Check the charging circuit as follows:
With the engine running from idling to 2,000 rpm, check
the reading on the ammeter and voltmeter.
Standard amperage: 10 A or less
Standard voltage:
at 25°C (77°F)13.9 - 15.1 V
at 115°C (239°F)13.5 - 14.3 V
If the voltmeter reading is greater than standard voltage, re-
place the voltage regulator.
If the voltmeter reading is less than standard voltage, check the
voltage regulator and generator as follows:

With terminal F grounded, start the engine and
check the voltmeter reading of terminal B.

If the voltmeter reading is greater than standard
voltage, replace the voltage regulator.

If the voltmeter reading is less than standard volt-
age, check the generator.
7. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater blower switch at
ºHIº.
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
If the ammeter reading is less than the standard amperage, re-
pair the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.

MX07F-04
Q06439
Z1891017 mm Head
Starter Set Bolt
Q06443
Q09187
Filler Plug
Oil Level
0 - 5 mm
Drain Plug MX-4
- MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE BATTERY AND AIR CLEANER CASE AS-
SEMBLY WITH AIR HOSE
2. REMOVE CLUTCH RELEASE CYLINDER AND LINE
CLAMP
(a) Remove the 2 bolts and release cylinder.
(b) Remove the 2 bolts and release cylinder line clamp.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
3. DISCONNECT GROUND CABLE
Remove the 2 bolts and disconnect the 2 ground cables from
the transaxle side and engine left mounting bracket side.
4. DISCONNECT BACK-UP LIGHT SWITCH CONNEC-
TOR
5. DISCONNECT CONTROL CABLE
(a) Remove the 2 clips and washers.
(b) Remove the 2 clips from the cables.
6. REMOVE STARTER SET BOLT
Remove the 2 set bolts of the starter from the transaxle upper
side.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
7. REMOVE TRANSAXLE MOUNTING BOLT
Remove the 3 bolts of transaxle case upper side.
Torque:
17 mm head: 64 N´m (650 kgf´cm, 47 ft´lbf)
8. INSTALL ENGINE SUPPORT FIXTURE
9. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
10. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
11. REMOVE LH AND RH ENGINE UNDER COVERS
12. DRAIN TRANSAXLE OIL
Oil grade: API GL-4 or GL-5
Viscosity: SAE 75W-90
Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
13. REMOVE LH AND RH DRIVE SHAFTS
(See page SA-17)