VAUXHALL ASTRA K 2020 Owner's Manual

Vehicle care269floor mats be purchased. Always
check that the floor mats do not
interfere with the pedals.
● Use the floor mat with the correct
side up. Do not turn it over.
● Do not place anything on top of the driver side floor mat.
● Use only a single floor mat on the
driver side.
● Do not place one floor mat on top
of another.
Inserting and removing the floor
mats
The driver side floor mat is held in place by two retainers.
To install the driver's side floor mat: 1. Move the driver's seat backwards
as far as possible.
2. Align slots in the mat with the retainers, as shown.
3. Turn retainers clockwise for aquarter turn.
Removing1. Move the driver's seat backwards
as far as possible.
2. Turn retainers a quarter turn towards the opposite direction
than during installation.
3. Remove the mat.

270Service and maintenanceService and
maintenanceGeneral information ...................270
Service information ..................270
Recommended fluids, lubricants
and parts .................................... 271
Recommended fluids and lubricants ................................ 271General information
Service information In order to ensure economical and
safe vehicle operation and to
maintain the value of your vehicle, it
is of vital importance that all
maintenance work is carried out at the proper intervals as specified.
The detailed, up-to-date service
schedule for your vehicle is available
at the workshop.
Service display 3 106.
European service intervals Maintenance of your vehicle is
required every 20,000 miles or after
one year, whichever occurs first. Engine oil and filter change is
indicated by the engine oil life system, when required earlier than
maintenance.
A shorter service interval can be valid for severe driving behaviour, e.g. for
taxis and police vehicles.
The European service intervals are
valid for the following countries:Andorra, Austria, Belgium, Bosnia-
Herzegovina, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany,
Greece, Greenland, Hungary,
Iceland, Ireland, Italy, Latvia,
Liechtenstein, Lithuania,
Luxembourg, North Macedonia,
Malta, Monaco, Montenegro,
Netherlands, Norway, Poland,
Portugal, Romania, San Marino,
Serbia, Slovakia, Slovenia, Spain,
Sweden, Switzerland, United
Kingdom.
Service display 3 106.
International service intervals Maintenance of your vehicle is
required every 10,000 miles or after
one year, whichever occurs first. Additional engine oil and filter change
is indicated by the engine oil life
system, when required earlier than
maintenance.
Severe operating conditions exist if
one or more of the following
circumstances occur frequently: Cold
starting, stop and go operation, trailer operation, mountain driving, driving

Service and maintenance271on poor and sandy road surfaces,
increased air pollution, presence of
airborne sand and high dust content,
driving at high altitude and large
variations of temperature. Under
these severe operating conditions,
certain service work may be required more frequently than the regularservice interval.
The international service intervals are
valid for the countries which are not
listed in the European service
intervals.
Service display 3 106.
Confirmations Confirmation of service is recorded inthe Service and warranty booklet.
The date and mileage is completed
with the stamp and signature of the
servicing workshop.
Make sure that the Service and
warranty booklet is completed
correctly as continuous proof of
service is essential if any warranty or
goodwill claims are to be met. It is also
a benefit when selling the vehicle.Recommended fluids,
lubricants and parts
Recommended fluids andlubricants
Only use products that meet the
recommended specifications.9 Warning
Operating materials are
hazardous and could be
poisonous. Handle with care. Pay
attention to information given on
the containers.
Engine oil
Engine oil is identified by its quality
and its viscosity. Quality is more
important than viscosity when
selecting which engine oil to use. The oil quality ensures e.g. engine
cleanliness, wear protection and oil
aging control, whereas viscosity
grade gives information on the oil's
thickness over a temperature range.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 275.
Topping up engine oilCaution
In case of any spilled oil, wipe it up and dispose it properly.
Engine oils of different manufacturersand brands can be mixed as long as
they comply with the required engine
oil quality and viscosity.
Use of engine oils for all petrol
engines with only ACEA quality is
prohibited, since it can cause engine
damage under certain operating
conditions.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 275.
Additional engine oil additives
The use of additional engine oil
additives could cause damage and
invalidate the warranty.

272Service and maintenanceEngine oil viscosity grades
The SAE viscosity grade gives
information of the thickness of the oil.
Multigrade oil is indicated by two
figures, e.g. SAE 5W-30. The first
figure, followed by a W, indicates the
low temperature viscosity and the
second figure the high temperature viscosity.
Select the appropriate viscosity grade
depending on the minimum ambient
temperature 3 275.
All of the recommended viscosity
grades are suitable for high ambient
temperatures.
Coolant and antifreeze
Use only organic acid type-long life
coolant (LLC) antifreeze approved for
the vehicle. Consult a workshop.
The system is factory filled with
coolant designed for excellent
corrosion protection and frost
protection down to approx. -28 °C. In
cold regions with very low
temperatures the factory filled coolant provides frost protection down to
approx. -37 °C. This concentrationshould be maintained all year round.
The use of additional coolant
additives that intend to give additional
corrosion protection or seal against
minor leaks can cause function
problems. Liability for consequences
resulting from the use of additional coolant additives will be rejected.
Washer fluid
Use only washer fluid approved for
the vehicle to prevent damage of
wiper blades, paintwork, plastic and
rubber parts. Consult a workshop.
Brake and clutch fluidOver time, brake fluid absorbs
moisture which will reduce braking
effectiveness. The brake fluid should
therefore be replaced at the specified
interval.

Technical data273Technical dataVehicle identification..................273
Vehicle identification number ..273
Identification plate ...................274
Engine identification ................274
Vehicle data ............................... 275
Recommended fluids and lubricants ................................ 275
Engine data ............................. 278
Performance ............................ 279
Vehicle dimensions .................281
Capacities ................................ 282
Tyre pressures ........................ 283Vehicle identification
Vehicle identificationnumber
The illustrations show different
versions.
The vehicle identification number
may be stamped on the identification
plate and on the floor pan, under the floor covering, visible under a cover.
The vehicle identification number
may be embossed on the instrument
panel, visible through the windscreen,
or in the engine compartment on the
right body panel.

274Technical dataIdentification plate
The identification plate is located on
the front left or right door frame.
Information on identification label:1:manufacturer2:type approval number3:vehicle identification number4:permissible gross vehicle weight rating in kg5:permissible gross train weight
in kg6:maximum permissible front axle
load in kg7:maximum permissible rear axle
load in kg8:vehicle-specific or country-
specific data
The combined total of front and rear
axle loads must not exceed the
permissible gross vehicle weight.
Vehicle's kerb weight depends on the
specification of the vehicle, e.g.
optional equipment and accessories.
Refer to the EEC Certificate of
Conformity provided with your vehicle
or other national registration
documents.
The technical data is determined in
accordance with European
Community standards. We reserve
the right to make modifications.
Specifications in the vehicle
documents always have priority over
those given in this manual.
Engine identification
The technical data tables use the
engine identifier code. The engine
data table additionally shows the
engineering code.
Engine data 3 278.
To identify the respective engine,
refer to the EEC Certificate of
Conformity provided with your vehicle
or other national registration
documents.
The Certificate of Conformity shows the engine identifier code, other
national publications may show the
engineering code. Check piston
displacement and engine power to
identify the respective engine.

Technical data275Vehicle data
Recommended fluids and lubricants
European service schedule Required engine oil qualityAll European countries with European service interval 3 270Engine oil qualityPetrol engines
F12SHL, F12SHR, F12SHT B14XFTPetrol engineF14SHTPetrol engineB16SHTDiesel enginesdexos1 Gen2✔–✔–dexos2––––OV0401547–✔✔✔
In case of dexos or OV0401547 quality is unavailable you may use max. 1l engine oil ACEA A3/B3 or C3 for petrol enginesand ACEA C5 for diesel engines.

276Technical dataEngine oil viscosity gradesAll countries with European service interval 3 270Petrol engines
F12SHL, F12SHR, F12SHTPetrol engine F14SHTPetrol engine
B14XFT, B16SHTDiesel enginesViscositySAE 0W-30
SAE 5W-30SAE 0W-20SAE 0W-20
SAE 0W-30
SAE 5W-30
SAE 0W-40
SAE 5W-40SAE 0W-20
International service schedule
Required engine oil quality
All European countries with European service interval 3 270Engine oil qualityPetrol engines
F12SHL, F12SHR, F12SHT B14XFTPetrol engineF14SHTPetrol engineB16SHTDiesel enginesdexos1 Gen2✔–✔–dexos2––––OV0401547–✔✔✔
In case of dexos or OV0401547 quality is unavailable you may use max. 1l engine oil ACEA A3/B3 or C3 for petrol enginesand ACEA C5 for diesel engines.

Technical data277Engine oil viscosity gradesAll countries with European service interval 3 270Petrol engines
F12SHL, F12SHR, F12SHTPetrol engine F14SHTPetrol engine
B14XFT, B16SHTDiesel enginesViscositySAE 0W-30
SAE 5W-30SAE 0W-20SAE 0W-20
SAE 0W-30
SAE 0W-40SAE 0W-20

278Technical dataEngine dataEngine identifier codeF12SHLF12SHRF12SHTF14SHTB14XFTB16SHTSales designation1.21.21.21.351.41.6Piston displacement [cm3
]119911991199134213991399Engine power [kW]8110796107110147at rpm4500550055005000 -60005000-56005500Torque [Nm]195225225236230280at rpm2000-35002000-35002000-35001500-35002000-40001650-4500Fuel typePetrolPetrolPetrolPetrolPetrolPetrolOctane rating RON 1)recommended959595959598possible989898989895possible919191919191Additional fuel type––––––1)
A country-specific label at the fuel filler flap can supersede the engine-specific requirement.