light VOLKSWAGEN BEETLE CONVERTIBLE 2013 3.G Owner's Manual

Opening and closing the convertible top

Fig. 30 In the roof console: convertible top button.
You can open or close the convertible top at speeds up to 30 mph (50 km/h). If the convertible top has
already begun opening or closing, it will stop if you exceed that speed. You can only continue opening
or closing the convertible top once the vehicle speed drops below about 30 mph (50 km/h).
For safety reasons, Volkswagen recommends opening or closing the convertible top only when the
vehicle is stationary and parked at a safe distance from moving traffic ⇒ .
Opening the convertible top
x Please note and follow the steps described in the checklists
x Switch on the ignition, if necessary
x Press and hold the button ⇒ fig. 30 in the roof console until all windows go down and the convert-
ible top is completely open ⇒ . A chime sounds and the indicator light in the instrument cluster
goes out when the process is complete. A message may also appear in the instrument cluster display.
x Secure the convertible top cover (boot), if necessary
Closing the convertible top
x Please note and follow the steps described in the checklists
x Switch on the ignition, if necessary
x Remove the convertible top cover (boot), if necessary
x Pull and hold the button until the convertible top and all windows close completely ⇒ : a chime
sounds and the indicator light in the instrument cluster goes out. A message may also appear in the
instrument cluster display.
Interrupting convertible top operation
Releasing the button interrupts convertible top operation ⇒ .

Fig. 33 A: Sliding in the bars on the wind blocker. B: Sliding in the locking pins.
The wind blocker is in a storage compartment in the vehicle's luggage compartment.
You can close the convertible top even when the wind blocker is installed.
Unfolding the wind blocker
Folding the wind blocker outward before installing it is the easiest way to get it into the correct position
for installation.
x Remove the wind blocker from the luggage compartment
x Fold both side sections outward in the direction of the arrows ⇒ fig. 32 until they lock into place.
Installing the wind blocker
The wind blocker is installed correctly when the longer side faces toward the front and the wind block-
er frame is on top.
x Insert both pins on the driver side of the wind blocker into the holes in the side trim panel above the
rear seats ⇒ fig. 33 A (1) (magnified area).
x Fold the handle B (4) at the front center of the wind blocker upward in the direction of the arrow
and hold it in place.
x Pull the section of the wind blocker that is facing the front passenger side upward slightly.
x Insert both pins on the wind blocker on the front passenger side into the holes in the side trim
panel above the rear seats B (2) (magnified area).
x Press down lightly on the center of the wind blocker B (3) until it locks into place.
x Pull the top section of the wind blocker upward so it contacts the stops and snaps into place.
Removing the wind blocker
x Fold the upper section of the wind blocker down toward the rear of the vehicle.
x Fold the handle B (4) at the front center of the wind blocker upward in the direction of the arrow
and hold it in place.
x Pull the center of the wind blocker upward opposite the direction of the arrow B (3).
x Remove both wind blocker retaining pins on the front passenger side from the holes in the side trim
panel opposite the direction of the arrows B (2).
x Remove both wind blocker retaining pins on the driver side from the holes in the side trim panel
opposite the direction of the arrows A (1).
Closing the wind blocker
x Fold the handle B (4) at the front center of the wind blocker upward in the direction of the arrow
and hold it in place.
x Fold both side sections inward opposite the direction of the arrow ⇒ fig. 32.

The convertible top button does not work when the convertible top cover is installed. If the button
is pressed anyway, the convertible top indicator light will blink as long as the button is pressed.
What to do if the convertible top will not move

Description Possible solution
The convertible top
will not open or close.
– Check to make sure all the preliminary requirements for convertible top
operation are met
– If the convertible top still will not operate, use the emergency procedure to
close the convertible top, if necessary
– Have the system checked by an authorized Volkswagen dealer or an
authorized Volkswagen Service Facility.
The convertible top
stops when opening
or closing.
– Check the instrument cluster display for information on what to do ⇒ table.
– Pull the button ⇒ fig. 30 to completely close and latch the convertible top.
– If the convertible top does not close completely and latch, try to close and
latch it using the emergency closing procedure
– Get professional help if necessary and have the system checked by an
authorized Volkswagen dealer, an authorized Volkswagen Service Facility,
or another qualified workshop.

Automatic Rollover Support System

Fig. 35 Behind the rear bench seat backrest: Automatic Rollover Support System.
The Automatic Rollover Support System® works with the reinforced windshield frame, properly worn
safety belts, and the airbag system, to help protect vehicle occupants in a rollover accident.
If the Automatic Rollover Support System is triggered, 2 supports behind the rear seat backrest deploy
upwards in a fraction of a second.
The Automatic Rollover Support System works only when the ignition is switched on. It deploys when
the convertible top is open as well as when it is closed.
The Automatic Rollover Support System is electronically controlled together with the airbag system. A
malfunction in the rollover support system is indicated by the airbag indicator light t in the instrument
cluster

The Automatic Rollover Support System can only deploy one time. After the Automatic Rollover Sup-
port System has deployed, you cannot slide it back into its original position. It must be replaced by an
authorized Volkswagen dealer or an authorized Volkswagen Service Facility.
The Automatic Rollover Support System may deploy in the following situations:
x In driving situations in which the vehicle tips sharply to one side, consistent with the values pro-
grammed into the electronic control module.
x In certain frontal, side, and rear-end collisions.
x In rollovers.
x If the vehicle briefly leaves the ground, for example when cresting a hill at a comparatively high
speed.
WARNING
The Automatic Rollover Support System can cause serious injuries if persons or objects are
in the way when it deploys.
x Never use accessory seat covers or protective covers that block the rollover protection
deployment area.
x Every rear seat passenger must be properly seated on a seat of his or her own and must
stay in a proper seating position at all times.
x Always keep the area around the supports free of anything that could interfere with their
deployment or fly about and injure occupants when the supports deploy.
x Never take the covers off the Automatic Rollover Support System.
x Never attach a child seat, child restraints, straps, or anything else to the rollover protec-
tion supports.
WARNING
If there is a system malfunction, the Automatic Rollover Support System may cause serious
injuries by not deploying properly, by not deploying at all, or by deploying unexpectedly.
x If a malfunction exists in the system, have it checked immediately by an authorized
Volkswagen dealer or an authorized Volkswagen Service Facility. A malfunction exists in the
system if the indicator light:
– does not come on when the ignition is turned on;
– does not go out about 5 seconds after you start the engine;
– goes out after switching on the ignition and then comes back on again;
– comes on or flickers when you are driving.
NOTICE
If deployed, the Automatic Rollover Support System can damage the convertible top fabric
when opening or closing the top.
x Do not open or close the convertible top if the Automatic Rollover Support System has
deployed.

WARNING
Always adjust seat, safety belts, and head restraints properly before driving and make sure
that all passengers are properly restrained.
x Push the passenger seat as far back as possible. Always be sure that there are at least
10 inches (25 cm) between the front passenger's breastbone and the instrument panel.
x Always adjust the driver's seat and the steering wheel so that there are at least 10 inches
(25 cm) between your breastbone and the steering wheel.
x Adjust the driver's seat so that you can easily push the pedals all the way to the floor
while keeping your knee(s) slightly bent. The distance to the instrument panel in the knee
area must be at least 4 inches (10 cm).
x If these requirements cannot be met for physical reasons, contact an authorized
Volkswagen dealer or an authorized Volkswagen Service Facility to see whether adaptive
equipment is available.
x Always hold the steering wheel on the outside of the steering wheel rim with your hands
at the 9 o'clock and 3 o'clock positions to help reduce the risk of personal injury if the driv-
er's airbag inflates.
x Never hold the steering wheel at the 12 o'clock position or with your hands at other places
inside the steering wheel rim or on the steering wheel hub. Holding the steering wheel the
wrong way can cause serious injuries to the hands, arms, and head if the driver's airbag in-
flates.
x Pointing the steering wheel toward your face decreases the ability of the driver's airbag to
help protect you in a collision.
x Never drive with backrests reclined or tilted back farther than necessary to drive comfort-
ably. The farther back the backrests are tilted, the greater the risk of injury caused by incor-
rect positioning of the safety belts and improper seating position.
x Never drive with the front seat passenger backrest tilted forward. If the front airbag de-
ploys, the front backrest can be forced backward and injure passengers on the rear seat.
x Sit as far back as possible from the steering wheel and the instrument panel.
x Always sit upright with your back against the backrest with the front seats properly ad-
justed. Never lean against or place any part of your body too close to the area where the air-
bags are located.
x Rear seat passengers who are not properly seated and restrained are more likely to be
seriously injured in a crash.
WARNING
Improper adjustment of the seats can cause accidents and severe injuries.
x Never adjust the seats while the vehicle is moving. Your seat may move unexpectedly and
you could lose control of the vehicle. In addition, you will not be in the correct seating posi-
tion while adjusting the seats.
x Adjust the front seat height, angle and longitudinal direction only if the seat adjustment
area is clear.
x The adjustment of the front seats must not be restricted by things in the footwell in front
or behind the seats.
Examples of improper seating positions

x Adjust the seat backrest angle to an upright position so that your back is in full contact with it when
the vehicle is moving.
x Always keep both feet on the floor and in the footwell whenever the vehicle is moving.
x Always adjust and fasten safety belts properly .
Driver–seat and steering wheel adjustment:
x Adjust the steering wheel so that there are at least 10 inches (25 cm) between the steering wheel
and your breast bone ⇒ fig. 36. When adjusting the proper distance to the steering wheel, grasp the
top of the steering wheel with your elbows slightly bent.
x Always hold the steering wheel on the outside of the steering wheel rim with your hands at the
9 o'clock and 3 o'clock positions to help reduce the risk of personal injury if the driver's airbag inflates.
x Never hold the steering wheel at the 12 o'clock position or with your hands at other places inside
the steering wheel rim or on the steering wheel hub. Holding the steering wheel the wrong way can
cause serious injuries to the hands, arms, and head if the driver's airbag inflates.
x Adjust the steering wheel so that the steering wheel cover points at your chest and not at your
face. Pointing the steering wheel toward your face decreases the ability of the driver's airbag to help
protect you in a collision.
x Adjust the driver's seat so that you can easily push the pedals all the way to the floor while keeping
your knee(s) slightly bent.
x Adjust the seat height so that the top point of the steering wheel can be reached.
x Always keep both feet in the footwell so that you are in control of the vehicle at all times.
Passenger–front seat adjustment:
x Push the passenger seat as far back as possible in order to ensure optimum protection if the
airbag is deployed.
Manual controls on the driver and passenger seat

Fig. 38 Controls on the left front seat.

Fig. 41 Removing the rear head restraints.
Please first read and note the introductory information and heed the WARNINGS
All seats are equipped with head restraints.
Removing the front head restraints
x Sit in the back seat behind the head restraint you want to remove.
x Pull the head restraint all the way up ⇒  in Adjusting the front and rear head restraints. Recline
the backrest with the head restraint so that there is enough overhead clearance to remove it.
x Slide a flat object, such as a plastic credit card, underneath the right side of the cap on the right-
hand seat guide rod ⇒ fig. 40 (1) to unlock the head restraint.
x Push the flat object (plastic card) in against the guide rod to depress a release button located
under the cap (not visible).
x Use one hand to hold the release button in with the flat object. With your other hand, lift the same
guide rod slightly to expose a notch in the rod at the bottom (can be seen and felt with fingers). The
right-hand guide rod is now released.
x To release the left-hand guide rod, press button (2) in (towards guide rod) and hold.
x Pull the head restraint out completely while holding button (2).
Installing the front head restraints
x Position head restraint properly over the head restraint guides of the respective seat backrest and
insert the head restraint into the guides.
x Push the head restraint down while pressing button (2).
x Move the seat backrest into an upright position using the adjusting wheel.
x Adjust the head restraint according to the occupant's size
Removing the rear head restraint
x Unlock the backrest of the rear seat bench and fold it forward
x Pull the head restraint all the way up ⇒ .
x If necessary, press the flat blade of the screwdriver from the vehicle tool kit into the slit of the trim
cap ⇒ fig. 41 (1) in the direction of the arrow and hold it in this position.
x At the same time press button (2) while a second person pulls out the head restraint completely.
x Fold the backrest of the rear seat bench back so that it locks securely.
Reinstalling the rear head restraint
x Unlock the backrest of the rear seat bench and fold it forward .

Function Action for seat heating ⇒fig.44
Switch on: Press the Aor ebutton. Seat heating is switched on
to maximum.
Adjust the heating
level:
Press the Aor e button repeatedly until the desired
heating level is set.
Switch off: Press the A or e button repeatedly until all indicator
lights in the button are off.

Special seat heating features
On the driver and the passenger side, the seat heating may resume at the setting that was set when
the ignition was switched off. However, this feature only works if the key is not taken out of the ignition
switch, or, for vehicles with Keyless Access, the driver door is not opened or the vehicle is not locked.
People suffering from a low level of perceived pain or a lowered awareness of pain as from medica-
tion, paralysis, or chronic illness (e.g. diabetes) should NEVER use the seat heating feature ⇒ !
The use of seat heating by persons with these conditions could result in burns to the back, buttocks,
and legs that may take a long time to heal and may never heal completely. If you have any of these
conditions, you should take regular breaks and get out of the vehicle, particularly on long trips. Consult
your doctor for advice regarding your specific condition.
WARNING
Certain medical conditions, such as paralysis and diabetes, and certain medications can
increase the risk of serious burns when the seat heating feature is switched on.
x Vehicle occupants who have a low level of perceived pain or a lowered awareness of pain
can receive serious burns to the back, buttocks, and legs that take a long time to heal or may
never heal completely.
x Never use the seat heating feature if you or your passengers are at risk of being burned
because of a medical condition. Take regular breaks and get out of the vehicle, particularly
on long trips. Consult your doctor for advice regarding your specific condition.
x Never let exposed skin remain in contact with the seat upholstery when the seat heating is
being used.
WARNING
A wet seat can cause the seat heating to malfunction and increase the risk of serious burns.
x Always make sure the seats are dry before using the seat heating.
x Never sit on the seat with wet clothes.
x Never put damp or wet things including clothes on the seat.
x Never spill liquids on the seats.
NOTICE
x To help prevent damage to electrical and other parts in the seat, do not kneel on the front
seats or apply concentrated pressure to a small area of the seat or backrest.
x Liquids, sharp objects and things that do not let the heat in the seat escape into the air,
including, for example, a child restraint, a blanket, or seat covers on the seat can damage seat
heating.

WARNING
Damage to safety belts reduces their overall effectiveness and increases the risk of serious
personal injury and death whenever the vehicle is being used.
x Never let safety belts become damaged by being caught in the door or seat hardware.
x Torn or frayed safety belts can tear, and damaged safety belt hardware can break in an
accident.
x Inspect belts regularly for damage. If webbing, bindings, buckles, or retractors are dam-
aged, have the belts replaced immediately with the correct replacement belts approved by
Volkswagen for your vehicle, model, and model year.
x Safety belts that were subject to stress in an accident and stretched must be replaced with
a correct, new safety belt, preferably by an authorized Volkswagen dealer or authorized
Volkswagen Service Facility.
x Replacement after a crash may be necessary even if a safety belt shows no visible dam-
age. Anchorages that have been loaded must also be inspected.
x Damaged safety belts must be replaced; they cannot be repaired.
x Never try to repair a damaged safety belt yourself. Never remove or modify the safety belts
in any way.
x Have safety belts, bindings, retractors and buckles replaced by an authorized Volkswagen
dealer or authorized Volkswagen Service Facility.
x Always keep the belts clean. Dirty belts may not work correctly and can impair the func-
tion of the inertia reel.
Warning light

Fig. 45 Warning light in the instrument cluster.

A warning chime also sounds.
The safety belt warning light ª comes on for 6 seconds when the ignition is switched on. A warning
chime also sounds for up to 6 seconds if the driver's safety belt is not buckled. The chime stops soon-
er if the driver buckles his or her safety belt. The warning light and the chime go out when both driver
and front passenger have bucked their safety belts.
If the driver and front seat passenger do not both fasten their safety belts within about 24 seconds
after the chime stops and the vehicle is moving at a speed of more than about 15 mph (25 km/h), the
chime will again sound for about 6 seconds, then go off for about 24 seconds, then sound again for
about another 6 seconds. The same thing happens if one of the safety belts is fastened and then
unfastened while the vehicle is moving. The safety belt warning light ª also flashes. The warning
chime continues to sound at 24 second intervals for up to 2 minutes. No chime sounds at speeds of
less than about 5 mph (8 km/h).
If the ignition is switched on, the safety belt warning light ª stays on until the driver and front passen-
ger have both buckled their safety belts.
WARNING
Not wearing a safety belt or wearing an improperly positioned safety belt increases the risk of
severe personal injury or death. Safety belts offer optimum protection only when used cor-
rectly.
Frontal collisions and laws of physics

Fig. 46 A vehicle with passengers not wearing safety belts approaches a wall.

Fig. 47 A vehicle with passengers not wearing safety belts hits a wall.
Please first read and note the introductory information and heed the WARNINGS