engine VOLVO C70 2006 User Guide
[x] Cancel search | Manufacturer: VOLVO, Model Year: 2006, Model line: C70, Model: VOLVO C70 2006Pages: 182, PDF Size: 3.35 MB
Page 47 of 182
Ashtrays/cigarette lighter
The auxiliary sockets can also be used for cigarette lighters. Ashtrays and lighters are available as accessories. Please
contact your Volvo retailer.
pg. 48 Instruments and controls
Power windows
Operation
The power windows are opened and closed using the buttons in the armrests, or can be opened by pressing the unlock
button on the central locking system's remote control (see page 87
).
Opening/closing the windows from inside the car
NOTE:
The ignition must be ON (ignition key in position I, II or the engine running) for the power windows to function.
The power windows will also function after the ignition has been switched off as long neither of the doors has been
opened.
Opening a window
Lightly press down the front edge of any of the buttons (A or B) to the first detent ("stop") to open a window to the
position of your choice.
WARNING!
Always remove the ignition key when the vehicle is unattended.
Never leave children unattended in the vehicle.
Make sure that the windows are completely unobstructed before raising or lowering them.
Press down the front part of one or both buttons A as far as possible and release to automatically open the front
window(s) completely.
To stop the window at any time, pull the button up.
Closing a window
ProCarManuals.com
Page 54 of 182
If your hand -held transmitter appears to program the HomeLink Universal Transceiver but the programmed button
does not activate the garage door, your garage door opener may have a rolling code.
Press the programmed HomeLink button. If the garage door opener has the rolling code feature, the HomeLink
indicator light flashes rapidly and then glows steadily after approximately 2 seconds.
To train a rolling code garage door opener, follow these instructions after programming the desired transceiver
button according to "Programming the transceiver." The help of a second person may make training easier.
1. Locate the training button on the garage door opener motor head unit. The location and color of the training button
may vary. If you encounter difficulty, refer to the garage door opener owner's manual or call toll-free 1-800-355-3515
(Internet: http://www.HomeLink.com
).
2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.
3. Press and release the programmed HomeLink button. Press and release the programmed HomeLink button a second
time to complete the training process.
4. Some garage door openers may require you to do this procedure a third time to complete the training.
5. The programmed button on your HomeLink Universal Transceiver should now operate your garage door opener.
The original handheld transmitter can also be used, as desired, to operate the garage door.
The remaining two HomeLink buttons can be programmed in the same way. In the event of any problems in
programming the HomeLink Universal Transceiver, call toll-free 1-800- 355-3515 (Internet:
http://www.HomeLink.com
).
Operating the HomeLink Universal Transceiver
Once programmed, the HomeLink Universal Transceiver can be used in place of your handheld transmitters.
To operate, the key must be turned to the "accessory" position (II) or the engine must be running. Press the
programmed HomeLink button to activate the garage door, driveway gate, security lightning, home security system etc.
Your original hand -held transmitters may, of course, be used at any time.
Erasing programmed buttons
Individual buttons cannot be erased, To erase all three programmed buttons:
1. Turn the ignition key to the "accessory" position (II).
2. Hold down the two outside buttons on the HomeLink Universal Transceiver for about 20 seconds, until HomeLink's
indicator light begins to flash.
3. Release both buttons.
pg. 55 Instruments and controls
Home Link® Universal Transceiver (option)
The HomeLink buttons can be reprogrammed using the procedures described on the previous page.
Reprogramming a single HomeLink button
1. Press and hold the desired HomeLink button. Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after approximately 20 seconds), position your hand -held
transmitter 2 to 5 in. (5 to 12 cm) away from the HomeLink surface.
3. Press and hold the hand -held transmitter button. The HomeLink indicator light will flash first slowly, then rapidly.
When the indicator light flashes rapidly, release both buttons.
ProCarManuals.com
Page 64 of 182
position.
pg. 68 Interior
Power seats
The power driver's seat can be adjusted:
If the ignition key is in position I or II.
During a 10 minute period after the doors have been unlocked if the door remains open.
If the door is closed and the ignition key is not yet in the ignition, or if the key is in position 0, the seat can be
adjusted or during a period of 40 seconds. The power passenger's seat can only be adjusted if the ignition key is in
position I or II, or if the engine is running.
Adjusting the seat
Controls 5, 6, and 7 on the side of the seat can be used to make adjustments.
5. Backrest tilt
6. Move this section of the control up or down to raise/lower the rear section of the seat. Move the control forward to
move the seat forward.
7. Move this section of the control up or down to raise/lower the front section of the seat. Move the control rearward
to move the seat rearward.
NOTE: The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs,
switch off the ignition (key in position 0) and wait for approximately 20 seconds before operating the seat again.
Emergency stop
NOTE: If the seat inadvertently begins to move, press any of the buttons to stop the seat.
Programming the seat memory, driver's seat only (option)
Three different seating positions can be stored (buttons 1, 2, and 3 in the illustration) in the seat's memory.
The following example explains how button 1 can be programmed. Buttons 2 and 3 can be programmed in the same
way.
To program (store) a seat position in button 1:
Use controls 5, 6, and 7 to adjust the seat to the desired position.
Press and hold down the M (memory) button.
With the M button depressed, press button 1 to store the seat's current position.
ProCarManuals.com
Page 66 of 182
The trunk divider (see page 71) must be closed.
The trunk must be closed.
The brake pedal must be depressed while the retractable hard top is in motion. Volvo also recommends the
following:
The vehicle should be parked outdoors, on level ground.
Raising or lowering the power retractable hard top should preferably be done in one, continuous operation.
If the vehicle is parked outdoors, the engine should be idling to help avoid battery drain.
CAUTION!
If the instructions on these pages are not followed, damage to the power retractable hard top's mechanism may occur.
WARNING!
The power retractable hard top must not be obstructed in any way when it is being operated. Always have an
unobstructed view of the power retractable hard top when it is in motion. See also the decal on the trunk divider.
Anyone near the vehicle should be well clear of the power retractable hard top's moving parts before it is
operated.
Children must never be allowed to play with the power retractable hard top control buttons.
pg. 71 Interior
Power retractable hard top
Trunk divider
ProCarManuals.com
Page 68 of 182
Raising or lowering the power retractable hard top
Turn the ignition key to position II, or start the engine if the vehicle is parked outdoors.
Press the brake pedal and keep it depressed while the retractable hard top is in motion.
Press and hold down the left button (1) to raise the power retractable hard top or the right button (2) to lower it. Hold
down the respective button until the top is completely raised or lowered.
Release the button when an audible signal sounds. The message ROOF OPEN or ROOF CLOSED will be displayed.
NOTE:
Please heed any messages that may appear in the information display while the top is in operation.
Any windows that are closed will be opened approximately 1 inch (2 cm) while the power retractable hard top is in
operation. The windows will be automatically re-closed when the top is completely raised or lowered.
pg. 73 Interior
Power retractable hard top
WARNING!
See the section "Before raising or lowering the power retractable hard top" on page 70
before operating the power
retractable hard top. Never pull the release wire for the power retractable hard top's hydraulic system that is located
under the rear seat cushion. This wire is only intended for use by qualified service personnel. Pulling this wire could
lead to:
High risk of being injured by the power retractable hard top mechanism.
Unexpected movement of the hard top, or the hard top or the trunk could inadvertently open.
The retractable hard top can be damaged.
Power retractable hard top-related text messages
PRESS BRAKE TO OPERATE ROOF
The brake pedal must be depressed while the retractable hard top is in motion.
CLOSE TRUNK FOR ROOF OPERATION
The trunk is open and must be closed before operating the power retractable hard top.
CLOSE TRUNK SEP. FOR ROOF OPERAT.
The trunk divider (see page 71
for more information) must be closed before operating the power retractable hard top.
LOW BATTERY FOR ROOF OPERATION
ProCarManuals.com
Page 69 of 182
The battery's charge is too low to operate the power retractable hard top. In this case, the top can only be raised. Start
the engine, or if necessary, have the battery charged before operating the top.
ROOF NOT LOCKED
The power retractable hard top is not fully up or down. Press and hold down the respective button again to complete
the operation.
TEMP LIMITS ROOF OPERATION
The power retractable hard top mechanism has overheated, or the ambient temperature is below 14° F (-10° C). If the
mechanism has overheated, wait for approximately 5 minutes (the message in the information display will disappear)
and try to lower or raise the top again.
If a fault in the power retractable hard top mechanism occurs, the following messages will be displayed:
ROOF FAILURE SERVICE REQUIRED
The power retractable hard top cannot be operated. Contact an authorized Volvo retailer or service technician. If the
top is down in this situation, a cover for the vehicle is provided in the trunk. See page 75
for more information.
ROOF FAILURE SEE MANUAL
The power retractable hard top must be operated according to the following instructions.
Emergency operation
If the message ROOF FAILURE SEE MANUAL is displayed, the power retractable hard top cannot be operated in the
normal way.
NOTE: If a fault has occurred and the power retractable hard top has been raised, it cannot be lowered again until the
fault has been corrected.
CAUTION!
Carefully read the information under "Before raising or lowering the power retractable hard top" on page 70 before
operating the power retractable hard top.
Damage may be unavoidable if the power retractable hard top must be operated under such conditions.
pg. 74 Interior
Power retractable hard top
Press button 1 or 2 (see the illustration on page 72) until ROOF FAILURE SEE MANUAL is displayed.
Release the button.
Press the button again and hold it down. After approximately 2 seconds, the power retractable hard top will begin to
move. Keep the button depressed until the top is fully raised.
NOTE:
Movement of the top may stop briefly. However, the button should be held down throughout the entire operation.
An audible signal will sound during the entire operation.
WARNING!
Never pull the release wire for the power retractable hard top's hydraulic system that is located under the rear seat
cushion. This wire is only intended for use by qualified service personnel. Pulling this wire could lead to:
High risk of being injured by the power retractable hard top's opening/closing mechanism.
Unexpected movement of the hard top/ the hard top or the trunk could inadvertently open.
ProCarManuals.com
Page 72 of 182
Interior lighting
1. Driver's side reading light
2. Courtesy lighting
3. Passenger's side reading light
The front seat reading lights can be switched on and off by pressing buttons 1 or 3.
The courtesy lighting (2) can be set to three positions:
Off - Press the right side of the button.
Neutral position - the interior courtesy lighting comes on when a door is opened, and is switched off when the door
is closed.
ON - Press the left side of the button.
Rear seat reading lights
The rear reading lights can be switched on or off by pressing the respective buttons.
Courtesy lighting - automatic function
The interior lighting has a built-in automatic function that switches on the courtesy lighting for 30 seconds when:
the car is unlocked from the outside using the key or remote control
the engine is switched off and the ignition key is turned to the 0 position.
The courtesy lighting lights up or remains on for 5 minutes when:
one of the doors is open
the courtesy lighting has not been switched off (the right side of button 2 depressed).
The automatic lighting goes out when:
the engine is started
ProCarManuals.com
Page 73 of 182
the car is locked from the outside using the key or remote control.
If the courtesy lighting is not switched off manually, it will be turned off automatically 5 minutes after the engine has
been switched off.
pg. 78 Interior
Interior lighting
Vanity mirror
Raise the cover to switch on the light.
pg. 79 Interior
Storage compartments
1. Storage pocket (also on front side of front seat cushion)
2. Compartment in door panel
3. Ticket clip
4. Glove compartment
5. Storage compartment behind the center instrument panel (retailer installed accessory)
6. Cup holders
7. Storage compartment in center console (for e.g. CDs)
ProCarManuals.com
Page 78 of 182
Auxiliary 12 volt socket (option)
Fold down the lid to use the socket.
Using the 12 volt socket while the engine is not running drains the vehicle's battery.
If the ignition is switched off and a device drawing more that 0.1A is connected to a socket, a battery alert will be
shown in the driver information display.
The cover should be kept on when the auxiliary socket is not in use.
pg. 84 Interior
Carrying long loads
Carrying long loads (ski hatch)
The center section of the rear seat backrest can be opened to create space for carrying long, light objects (max. length
6.5 ft/2 meters, max. weight 55 lbs/25 kg). To do so, the center section (cushion) of the rear seat backrest must be
removed, and the plastic hatch in the trunk must be opened.
Removing the center backrest cushion
Pull the strap at the upper edge of the cushion, pull it forward, and lift it out.
Opening the plastic hatch
From the trunk, press the catches in the two holes in the hatch toward each other to release the hatch, and fold it down.
NOTE: If the vehicle is equipped with the optional ski bag, the bag's zipper must be opened from the passenger's
compartment in order to insert objects through the ski hatch.
ProCarManuals.com
Page 84 of 182
The vehicle's doors can be locked or unlocked
The engine can be started
Locking points C, D, E, F, and G cannot be unlocked with the remote control.
Activating the valet locking function
Remove the key blade from the remote control.
Turn the key blade 180° clockwise in the glove compartment lock to lock points C, D, E, F, and G and disconnect
these points from the central locking system (a message appears in the information display).
Give the parking attendant or service personnel only the remote control (with the key blade removed).
Deactivating the valet locking function
Turn the key blade 180° counterclockwise in the glove compartment lock to deactivate valet locking.
pg. 90 Locks and alarm
Glove compartment and trunk
Locking the glove compartment
The glove compartment can only be locked and unlocked using the detachable key blade on the remote control.
Unlock the glove compartment by turning the key a quarter of a turn (90°) counterclockwise. The key slot is vertical
when the glove compartment is unlocked.
Lock the glove compartment by turning the key a quarter of a turn (90°) clockwise. The key slot is horizontal when the
glove compartment is locked.
ProCarManuals.com