remote start VOLVO V90 2017 Owner's Manual

LOCKS AND ALARM
}}
* Option/accessory.253
NOTE
•A door's lock reset only locks that partic- ular door - not all doors simultaneously.
• A manually locked rear door with acti-vated manual or electric child safety lockscannot be opened from either the outsideor the inside. A rear door that is locked inthis way can only be unlocked with theremote control key or central locking but-ton.
Related information
• Detachable key blade (p. 250)
Power operated tailgate
*
The car's tailgate can be opened/closed electri- cally.
Opening/closing via a foot movement is also available as an extended option - see the section"Opening/closing the power operated tailgatewith foot movement" for more information.
OpeningThe tailgate can be opened with its handle, with foot movement *, a button on the instrument
panel or the remote control key.
Opening/closing button on the instrument panel.
Choose one of the following options to open the tailgate:
• Light press on the tailgate handle.
• Long press on the instrument panel's
button. Keep it depressed until the tailgate starts to open.
• Long press on the remote control key's
button. Keep it depressed until the tailgate starts to open.
ClosingThe tailgate can be closed via the instrument panel's button, with foot movement *, with the
remote control key or the buttons 12
along the
bottom edge of the tailgate. Choose one of the following options to close the tailgate.
–Long press on the instrument panel's
button or the remote control key's but-
ton.
> The tailgate closes automatically and acoustic signals sound - the tailgate remains unlocked.
12A car with keyless locking/entry (Passive Entry *) has one button for closing and one button for closing and locking.

LOCKS AND ALARM
* Option/accessory.255
2.
Press the
button on the underside of
the tailgate for at least 3 seconds.
> Two short acoustic signals sound to indi- cate that the set position has been saved.
To reset max. opening:
–Manually move the tailgate to its highest possible position - press the
button on
the tailgate for at least 3 seconds.
> Two acoustic signals sound to indicate that the set position has been cleared. The tailgate will then assume its max.position when opened.
NOTE
• If the system has been operating continu- ously for a long time, it is switched off toavoid overload. It can be used again afterabout 2 minutes.
Pinch protectionIf something with sufficient resistance prevents the tailgate from opening/closing then the pinchprotection is activated.
• During opening - movement is interrupted,the tailgate stops and a long acoustic signalsounds.
• During closing - movement is interrupted, thetailgate stops, a long acoustic signal soundsand the tailgate returns to the programmedmax. position.
WARNING
Observe the risk of trapping when opening/ closing. Before starting opening/closing,check that there is nobody near to the tailgateas trapping may have serious consequences. Always operate the tailgate with caution.
Pre-tensioned springs
The pre-tensioned springs for the power operated tail- gate.
WARNING
Do not open the pre-tensioned springs for the power operated tailgate. They are pre-ten-sioned with high pressure and can causeinjury if opened.
Related information
• Opening/closing the tailgate with foot move- ment
* (p. 256)
• Remote control key range (p. 238)

LOCKS AND ALARM
}}
* Option/accessory.257
NOTE
There is a risk of reduced function, or no function, if the rear bumper is loaded withlarge amounts of ice, snow, dirt or similar. Forthis reason, make sure you keep it clean.
NOTE
Pay attention to the possibility that the sys- tem may be activated in a car wash or similarif the remote key is within range.
Related information
•Locking/unlocking the tailgate (p. 247)
• Power operated tailgate
* (p. 253)
• Remote control key range (p. 238)
Replacing the battery in the remote control key
The battery in the remote control key needs to be replaced when it has become discharged.
NOTE
All batteries have a limited service life and must eventually be replaced (does not applyto Key Tag). The service life of the battery var-ies depending on how often the vehicle/keyis used.
The battery for the remote control key should be replaced if:
the information symbol illuminates and the message
Car key battery low
See Owner's manual is shown in the
driver display
and/or
• the locks repeatedly do not react to signals from the remote control key within 20 metresfrom the car.
NOTE
Always try moving closer to the car and mak- ing another unlock attempt.
The battery in the button-less key 16
(Key Tag)
cannot be replaced - a new key can be ordered from an authorised Volvo workshop.
IMPORTANT
A discharged Key Tag must be handed over to an authorised Volvo workshop. The keymust be deleted from the car since it is stillpossible to use it to start the car via back-upstart.
16 This key is supplied with a car equipped with the keyless locking/entry option (Passive Entry *).

||
LOCKS AND ALARM
* Option/accessory.
260
Turn the remote control key over and refit
the front side's shell by pressing it down until a clicking sound can be heard.
Then slide the shell back sedan.
> A further click will indicate that the shell is securely attached.
IMPORTANT
Make sure that exhausted batteries are dis- posed of in a manner which is kind to theenvironment.
Related information
• Remote control key (p. 236)
Immobiliser
The electronic immobiliser is a theft protection system that prevents an unauthorised personfrom starting the car.
The car can only be started with the correct remote control key. The following error message in the driver display is related to the electronic immobiliser:
Symbol Message Specification
Car key not found See Owner'smanualError reading the remote control keyduring starting -place the key in thecup holder near thekey symbol and tryagain.
Remote-controlled immobiliser with tracking system 17
The car is fitted with a system which makes it possible to track and locate the car and toremotely activate the immobiliser, which preventsstarting the engine. Contact your nearest Volvodealer for more information and assistance withactivating the system. The following error message in the driver displayis related to the remote-controlled immobiliserwith tracking system:
Symbol
Message Specification
Remotely immobilised Car not pos- sible to startThe remote-con- trolled immobiliserwith tracking sys-tem is activated.The car cannot bestarted. ContactVolvo On CallService Centre.
Related information
•Remote control key (p. 236)
• Remote control key range (p. 238)
17
Only certain markets and in combination with Volvo On Call *.

LOCKS AND ALARM
}}
* Option/accessory.261
Child safety locks
The child safety locks prevent children from being able to open a rear door from the inside. There is an electric * and a manual lock.
Electric activation/deactivation *The electric child safety locks can be activated/ deactivated in all ignition positions higher than 0.
Activation/deactivation can be performed up to 2 minutes after switching off the engine, providedthat no door is opened. See the section "Ignitionposition" for more information.
Button for electric activation/deactivation.
1. Start the engine or choose an ignition posi-
tion higher than 0. 2. Press the button in the driver's door control
panel.
> The driver display shows the message
Rear child lock Activated and the but-
ton's lamp illuminates - the locks are active.
When the electric child safety lock is active thenthe rear:
• windows can only be opened with the driver'sdoor control panel
• doors cannot be opened from inside.
To deactivate the locks:
–Press the button in the driver's door control panel.
> The driver display shows the message
Rear child lock Deactivated and the
button's lamp goes out - the locks are deactivated.
The current setting is stored when the engine isswitched off - if the child safety locks are acti-vated at engine shutdown, the function willremain activated the next time the engine isstarted.
Symbol Message Specification
Rear child lock Acti-
vatedChild safety locks are acti-vated.
Rear child lock Deacti-
vatedChild safety locks are deacti-vated.
Manual activation/deactivation
Manual child safety locks. Not to be mixed up with man- ual door locks.
–Use the remote control key's detachable key blade to turn the knob. For more information,see the section "Detachable key blade".

||
LOCKS AND ALARM
* Option/accessory.
262
The door is blocked against opening from the inside.
The door can be opened from both the out- side and the inside.
NOTE
• A door's knob control only blocks that particular door - not both rear doorssimultaneously.
• Cars with an electric child safety lock donot have a manual child lock.
Related information
• Detachable key blade (p. 250)
• Ignition positions (p. 385)
Alarm
*
The alarm alerts e.g. in the event of a break-in in the car.
When armed, the alarm is triggered if:
• a door, the bonnet or the tailgate is opened 18
• a movement is detected in the passenger compartment (if fitted with a movement detector
*)
• the car is raised or towed away (if fitted witha tilt detector
*)
• the starter battery's cable is disconnected or
• the siren is disconnected.
If there is a fault in the alarm system, the driver display shows the symbol and the message
Alarm system
failure Service required. In which
case, contact a workshop - an authorised Volvo workshop is recommended.
NOTE
Do not attempt to repair or alter components in the alarm system yourself. Any suchattempts may affect the terms of the insur-ance.
NOTE
The movement sensors trigger an alarm in the event of movement in the passengercompartment - air currents are also regis-tered. For this reason the alarm is triggered ifthe car is left with a window or the panoramic roof * open or if the passenger compartment
heater is used. To avoid this: Close the window/panoramic roof when leaving the car. If the car's inte-grated parking heater (or a portable electricheater) shall be used - direct the airflow fromthe air vents so that they are not pointingupwards into the passenger compartment.Alternatively, reduced alarm level can be used- see the section further down in this article.
Arming the alarmLock and arm the car alarm as follows:
• press the remote control key's lock button
• touch in the marked area on the outside of the door handle 19
or
• push on the tailgate's rubberised pressureplate 19
.
If the car is equipped with a power-operated tail- gate, the button on the underside of the tailgatecan also be used to lock the car and arm the caralarm.
18 Applies to certain markets.
19 Only applies to a car with keyless locking/entry (Passive Entry *)

LOCKS AND ALARM
* Option/accessory.263
Deactivate the alarmUnlock and disarm the car alarm as follows:
• press the remote control key's unlock button
• grip one of the door handles 19
or
• push on the tailgate's rubberised pressure plate 19
.
Switching off a triggered alarm
–Press the remote control key's unlock button or set the car in ignition position I by turning
the ignition dial to START and then releas-
ing.
NOTE
• Remember that the alarm is activated when the car is locked.
• If any of the doors are opened from theinside then the alarm is triggered.
Alarm signalsWhen the alarm has been triggered, the following happens:
• A siren sounds for 30 seconds or until thealarm is switched off.
• The direction indicators flash for 5 minutesor until the alarm is switched off. If the cause of alarm activation is not rectified, the alarm cycle is repeated up to 10 times
20
.
Lock and alarm indicator
A red LED on the instrument panel indicates the alarm system's status:
• LED not lit – alarm not armed.
• The LED flashes once every other second –alarm is armed.
• After the alarm has been disarmed, the LEDflashes rapidly for up to 30 seconds or until ignition position
I has been selected by turn-
ing the ignition dial to START and releasing
it - the alarm has been triggered.
Reduced alarm levelReduced guard means that the movement and tilt detectors can be temporarily deactivated. Switch off the movement and tilt detectors in order to avoid accidental triggering of the alarm -e.g. if a dog is left in a locked car or during trans-port on a car train or car ferry. The procedure isthe same as with the temporary disengaging ofthe deadlocks function.
Press the
Reduced guardbutton in the centre display's function view in order to switchoff the movement and tiltdetectors temporarily.
For more information, see the section "Dead- locks".
Related information
•Automatic arming/rearming of the alarm
*
(p. 264)
• Disarming the alarm
* without working remote
control key (p. 264)
• Deadlocks
* (p. 246)
19
Only applies to a car with keyless locking/entry (Passive Entry *)
20 Applies to certain markets.

LOCKS AND ALARM
* Option/accessory.
264
Automatic arming/rearming of the alarm *
Automatic rearming of the alarm prevents the car being left with the alarm disarmed unintention-ally.
If the car is unlocked with the remote control key (which disarms the alarm) but none of the doorsor the tailgate is opened within two minutes, thenthe alarm is automatically re-armed. The car isrelocked at the same time. In certain markets, the alarm is re-armed auto- matically after a certain delay after the driver'sdoor has been opened and closed without beinglocked.
Related information
• Alarm
* (p. 262)
• Disarming the alarm
* without working remote
control key (p. 264)
Disarming the alarm * without
working remote control key
The car can be unlocked and disarmed even if the remote control key does not work, e.g. if theremote control key's battery is dead.
1. Open the driver's door with the detachable key blade.
> The alarm is triggered.
The backup reader's location in the cup holder.
2. Place the remote control key in the backupreader in the tunnel console's cup holder.
3. Turn the ignition dial to START and release.
> The alarm is deactivated.
Related information
• Alarm
* (p. 262)
• Automatic arming/rearming of the alarm
*
(p. 264)
• Detachable key blade (p. 250)
• Starting the car (p. 386)

LOCKS AND ALARM
}}
* Option/accessory.265
Type approval for the remote control key system
Type approval for the remote control key system can be read in the table.Lock system keyless start (Passive Start) and keyless locking/unlocking (Passive Entry *)
CEM marking for the remote control key system. For supplementary type approval number, see the tablebelow.
Country/Area Type approval
Jordan TRC/LPD/2014/250
Serbia P1614120100
Argentina CNC ID: C-14771

STARTING AND DRIVING
}}
385
Ignition positions The car's electrical system can be set in different levels/positions and in this way make the differ-ent functions available.
In order to facilitate the use of a limited number of functions with the engine switched off, thecar's electrical system can be set in 3 different levels - 0, I and II. These levels are described
with the denomination "ignition position" throughout the owner's manual. The following table shows the functions available in each ignition position/level:
Level Functions
0 •Odometer, clock and temperature gauge are illuminated.
• Power seats can be adjusted.
• The power windows can be used.
• The centre display is started andcan be used.
• It is possible to start the audio.
The functions are time-controlled inthis ignition position and are switchedoff automatically after a period of time.
I •Panorama roof, power windows,12V socket in the passenger com-partment, navigation, phone, venti-lation fan and windscreen wiperscan be used.
• Power seats can be adjusted.
• 12 V sockets in the cargo areacan be used.
• The audio is started automaticallyif it was running when the car wasleft.
Power is taken from the battery inthis ignition position.Level Functions
II •The headlamps come on.
• Warning/indicator lamps illuminate for 5 seconds.
• Several other systems are acti-vated. However, heating in seatcushions and the rear window canonly be activated after the car hasbeen started.
This ignition position consumes alot of current from the battery andshould therefore be avoided!
Selecting ignition position
Start knob in the tunnel console.
• Ignition position 0
- Unlock the car and
store the remote control key inside the car.