buttons VOLVO XC90 2014 Owner´s Manual

03 Climate
Electronic climate control (ECC)
03
100* Option/accessory, for more information, see Introduction.
switch will light up to indicate that the defrost function is engaged.
• Blower speed increases automatically and the air conditioning will switch on (ifnot already on and if the passenger com-partment blower is not turned off) todehumidify the air in the passenger com-partment.
• Recirculation will not function whiledefrost is engaged.
The climate system will return to its previous settings when the defroster function isswitched off.
Rear window and door mirror
defrosters
This function defrosts/deices the rear window and door mirrors. The LED in the switch willlight up to indicate that the heating function isengaged. For additional information on thisfunction see page 75. Never use ice scrapers made of metal as they can easily scratch the mirror surface.
Heated front seats*
1. Press the switch once for maximum seat heating. Both LEDs in the switch will be lit. 2. Press the switch a second time for com-
fort heating. One LED in the switch will belit.
3. Press the switch a third time to turn the heating off completely. The LED will gooff.
The seat heating for the passenger seatshould be switched off when the seat is notoccupied.
Heated rear seats (XC90 Executive*)
G030976
Button for rear seat heating Heating for the respective outboard rear seats can be switched on or off with buttons on either side of the center console (see theillustration). To switch on rear seat heating:
–Press the button.
> The symbol in the button will illumi-
nate.
To switch off rear seat heating:
–Press the button.
> The symbol in the button will go out.
Temperature
These controls are used to individually set the temperature for both sides of the passengercompartment. Please note that the compart-ment will not be heated or cooled faster bysetting the temperature higher or lower thannecessary. Set the control to the temperature you prefer.
Blower control 1
Turn the control clockwise to increase or counterclockwise to decrease the blowerspeed. Pressing the
AUTO switch will auto-
matically regulate blower speed and overridemanual adjustment. Turning the blower control counterclockwise until an orange LED comes on will turn boththe blower and the air conditioning off.
1 See also see page 94.

04 Interior
Front seats
04
* Option/accessory, for more information, see Introduction.105
Power seat*
OperationDriver's seat: The seat can be adjusted if the
ignition key is in position I, II or if the engine
is running. It can also be adjusted as follows with the ignition off:
• Within several minutes after the driver's door has been unlocked from the outside,has been opened, and remains open.
• Within a short period if the driver's doorhas just been closed.
• Within a short period if the driver's doorhas not been opened after the ignitionhas been switched off.
Passenger seat: The seat can only be
adjusted if the ignition key is in position I, II or
if the engine is running.
G027036
Power seat adjustment controls
Seat adjustmentAdjust the power seat(s) with the two controls at the side of the seat as follows:
Front edge of seat (raise/lower)
Forward – rearward
Rear edge of seat (raise/lower)
Backrest tilt
NOTE
The power seats have an overload protec- tor that activates if a seat is blocked byany object. If this occurs, switch off theignition (key in position 0 ) and wait for ashort period before operating the seatagain.
Emergency stopIf the seat accidentally begins to move, press any of the buttons to stop the seat.
NOTE
Please refer to the following page for infor- mation on programming the memory func-tion in the driver's seat.
Remote keyless entry system and the driver's seat
The remote key transmitter also controls the position of the electrically operated driver'sseat in the following way:
• Adjust the seat to your preferences.
• When you leave your vehicle, lock it using the remote key.
The position of the seat is now stored in the remote key.

04 Interior
Front seats
04
106* Option/accessory, for more information, see Introduction.
Automatic seat adjustmentTo move the seat to the position in which you left it:
1. Unlock the driver's door with the same
remote key (the one used to lock the doors)
2. Open the driver's door within 2 minutes. The driver's seat will automatically move to the position in which you left it.
NOTE
• The seat will move to this position even if someone else has moved it to adifferent seating position and lockedthe vehicle with a different remote key.
• This feature will work in the same waywith all of the remote key transmitters(up to 3 ) that you use with your vehi-cle.
• This feature will not function if you lockyour vehicle with the key.
WARNING
•Because the driver's seat can be adjusted with the ignition off, childrenshould never be left unattended in thevehicle.
• Movement of the seat can be STOP-PED at any time by pressing any but-ton on the power seat control panel.
• Do not adjust the seat while driving.
• The seat should be adjusted so thatthe brake pedal can be depressedfully. In addition, position the seat asfar rearward as comfort and controlallow.
• The seat rails on the floor must not beobstructed in any way when the seat isin motion.
G027037
Programming the memoryThree different seating and door mirror posi- tions can be stored in the driver seat's mem-ory. The following example explains how button 1 can be programmed. Buttons 2 and 3 can beprogrammed in the same way. To program (store) a seat position in button 1:
1. Move the seat to the desired position
using the seat adjustment controls (see page 104).
2. Press and hold down the MEM (memory)
button.

04 Interior
Interior lighting
04
}}
111
Reading lights and courtesy light
G026960
Driver's side front reading lamp
Courtesy lights
Passenger's side front reading lamp The reading lights can be switched on or offby pressing buttons 1 or 3. The courtesylighting (including footwell lighting) can beturned on or off by pressing button 2.This also activates the automatic func-tion.
G027153
Rear reading lights
Driver's side rear reading light
Passenger's side rear reading light. The rear reading lights can be switched onand off by pressing buttons (4) or (5).
Automatic functionThe reading lights and courtesy lights willswitch off automatically approximately10 minutes after the engine has been turnedoff. The lights can be turned off sooner bypressing the respective buttons.The courtesy lights come on automatically
1
and remain on for approximately 30 secondswhen: • The vehicle has been unlocked from the outside with the remote key or key blade
• If the engine has been switched off andthe ignition key has been turned to posi-tion 0
The courtesy lights will come on and remain on for approximately 10 minutes when:
• One of the doors is opened (assuming the courtesy lighting has not previously beenswitched off)
The courtesy lighting will go off when:
• The engine is started
• The vehicle is locked from the outsidewith the remote key or key blade
The automatic function can be disconnected by pressing button (2) for more than 3 sec-onds. Briefly pressing the button again automati- cally reconnects the function. The courtesy light timer periods can be changed. Contact a trained and qualifiedVolvo service technician.
1 This function is light dependent and is only activated in dark conditions.

04 Interior
Securing cargo
04
120
Attachment eyelet in front seat rail
If the vehicle is equipped with the cargo area cover, lift the cover out of the vehicle beforeinstalling the cargo net.
1. The upper and lower rods of the cargo net are hinged. Position the rods so that they are straight and lock in position.
2. Insert the end of the upper rod in one of the attachment brackets (see illustrationin the left column).
3. Insert the other end of the rod in the attachment bracket on the opposite sideof the vehicle.
NOTE
When using the net in the rear attachment brackets, be sure it is installed in front ofthe side armrests.
4. Attach the lower straps to the eyelets onthe floor if the net has been installed in the rear attachment brackets. Use theeyelets in the front seat rails if the net hasbeen installed in the forward attachmentbrackets.
5. Adjust the straps to pull the net taut.
Folding and storing the cargo netPress the release buttons on the hinges (1 in the illustration) and fold the net.
WARNING
• Be sure the cargo net is properly inserted in the attachment bracketsand the straps are correctly attachedto the eyelets and pulled taut.
• Do not use the net if it is damaged inany way.
• When it is not in use, store the net sothat it cannot be thrown forward in theevent of sudden braking, etc.
G027056
Upper attachments

05 Locks and alarm
Remote keys and key blades
05
129
WARNING
Never use the transmitter to lock the doors from inside the vehicle.• Doing so would ACTIVATE:
• the break-in alarm, which would sound if one of the doors were opened
• the optional interior motion and incli-nation alarm sensors.
• Doing so would DEACTIVATE:
• the moonroof and interior courtesylight controls.
• the central locking buttons on the frontdoor armrests, although the interiordoor handles would still function toallow occupants to leave the vehicle.
• Disabled features would remain disa-bled until the remote is used again tounlock the vehicle.
• In addition, locking an occupied vehi-cle would hinder rapid access to theoccupants in an accident or emer-gency.
Replacing the battery in the remote keyIf the range of the transmitter is noticeably reduced, this indicates that the battery isweak and should be replaced.
To replace the battery:1. Carefully pry open the rear edge of the
cover with a small screwdriver.
2. Insert a new 3-volt, CR2032 battery, with the battery's plus side up. Avoid touching the contact surfaces of the battery withyour fingers.
3. Press the cover back into place. Ensure that the rubber seal is correctly posi-tioned to help keep out moisture.
NOTE
The old battery should be disposed of properly at a recycling center or at yourVolvo retailer.

05 Locks and alarm
Child safety locks
05
132* Option/accessory, for more information, see Introduction.
G021513
Child safety locks in the rear doors - driver's side and passenger's side respectively
Manual child safety locks – rear doorsThe controls are located on the rear door jambs. Use a key or small screwdriver toadjust these controls.
Turn outward: the door cannot be
opened from the inside. The door can be opened from the outside.
Turn inward: the door locks function
normally (the door can be opened from the inside).
WARNING
Remember, in the event of an accident, the rear seat passengers cannot open thedoors from the inside with the buttons inposition A.
REAR AC
G027105
Power child locks*To prevent the rear doors from being opened from the inside:
1. Turn the vehicle's ignition key to at least
position I or II.
2. Press the button in the center console (see the illustration). Indicator light in the button ON:
the rear
doors and windows cannot be opened from the inside. Indicator light in the button OFF: the rear
doors can be opened from the inside and the windows can be opened. A message will appear in the instrument panel display when the child safety locks areactivated/deactivated.

05 Locks and alarm
Alarm
05
* Option/accessory, for more information, see Introduction.133
The alarm is automatically armed whenever you lock your vehicle. When armed, the alarm continuously moni- tors a number of points on the vehicle. Thefollowing conditions will set off the alarm: •
The hood is forced open.
• The tailgate is forced open.
• A door is forced open.
• The ignition switch is tampered with.
• If there is movement in the passenger compartment (if the vehicle is equippedwith the optional movement sensor).
• The vehicle is lifted or towed (if the vehi-cle is equipped with the optional inclina-tion sensor).
• The battery is disconnected (while thealarm is armed).
• The siren is disconnected when the alarmis disarmed.
Arming the alarm1. Press the
LOCK button on the remote
key.
2. Lock the vehicle using the key blade in the driver's door or press the central lock button on the driver's door with the dooropen.
One long flash of the turn signals will confirmthat the alarm is armed.
Movement sensor*In addition to triggering the alarm if there ismovement in the passenger compartment,currents of air may also affect the movementsensor. This means that locking the vehiclewith the windows or the moonroof open, orusing an accessory portable passenger com-partment heater, could trigger the alarm. To help avoid this, close the windows and moonroof before locking the vehicle. If a pas-senger compartment heater is used when thevehicle is locked, direct airflow from the heat-er's vent(s) so that it isn't directed upward inthe passenger compartment.
Disarming the alarmPress the UNLOCK button on the remote key
or unlock the doors with the key blade.
Turning off (stopping) the alarmIf the alarm is sounding, it can be stopped bypressing the UNLOCK button on the remote
key or by unlocking the driver's door with thekey blade.
Visual alarm signalThe visual alarm signal is given by flashing allturn signals and turning on the interior lightingfor approximately 5 minutes.
Audible alarm signalAn audible alarm signal is given by a batterypowered siren. One alarm cycle lasts for25 seconds.
"Panic" buttonIn an emergency situation, this feature can beused to attract attention. Activate the "panic" button by pressing the red button on the remote key ( see page 127for illustration) for at least 3 seconds or bypressing this button twice within 3 seconds.The turn signals will flash, and the vehicle'shorn will sound. The function can be turned off by pressing any of the buttons on the remote key or willstop automatically after 25 seconds. When abutton is pressed, there is a 5 second delaybefore the panic alarm is deactivated.
NOTE
This button will NOT unlock the vehicle.
LED alarm status signalsThe status of the alarm system is indicated by the red LED at the top of the dash: • LED off – the alarm is not armed
• LED flashes once per second – the alarm is armed

10 Audio
Audio system overview
10
252* Option/accessory, for more information, see Introduction.
CD player
VOLUME – turn to adjust
POWER – On/Off
AM/FM – for switching between FM1,
FM2 and AM
Display
ENTER – select in the menu or activate a
selection
PHONE : press to turn standby on/off.
MY KEY – programmable key for your
favorite function from the menu
SELECTOR – select sound source
SOUND – make sound settings
EXIT/CLEAR – step back in the menu or
cancel a selection
Not in use
MENU – menu selections/navigation
CD eject
CD slot, CD changer*
search for and store the strongest radio stations in the area in which you are driv-ing
Station preset buttons/select a disc in the CD changer* ( 1-6)
IR* Infrared port – for the optional naviga-
tion system remote control

10 Audio
Audio system controls
10
}}
253
Steering wheel keypad
G027135
The four buttons on the steering wheel key- pad can be used to control the audio system.The steering wheel keypad can be used toadjust volume, shift between preset stationsand change CD tracks.
• Press the
or buttons briefly to
search for a radio station, or to go to the next/previous track on a CD.
• Press and hold down these buttons tosearch within a track.
Accessing and using menus
G027112
In menu mode, you can change settings and program new functions in the audio system.The various menu alternatives are shown inthe display, and the current level in the menustructure is shown at the upper right corner ofthe display. Press the
MENU button to enter menu mode.
Use the menus as follows:
• Use the menu arrow keys (1) to navigate up or down in the menus. Dots in the dis-play indicate that there are more menuselections from which to choose.
• Press
ENTER to confirm or cancel a
menu selection. •
One long press on
EXIT/CLEAR exits
menu mode.
• A short press on the
EXIT/CLEAR ena-
bles you to cancel, undo, or answer no toa menu selection, or to go back in themenu structure.
Shortcut
The menu alternatives are numbered and can be accessed directly by pressing the respec-tive keys on the numbered keypad on the leftside of the audio panel.
MY KEY – programming a shortcut
Use the MY KEY button to program a favorite
function from the menu, such as RANDOM,
etc.
1. Use the MENU buttons to scroll among
the functions.
2. Select the desired function from the menu by pressing the MY KEY button for more
than two seconds.
3. When
MY KEY STORED is shown in the
display, the function has been stored.
4. Activate the function by briefly pressing the MY KEY button.
Repeat steps 1 – 4 to store new functions on the MY KEY buttons.