lock VOLVO XC90 TWIN ENGINE 2019 Service Manual

WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory. 173
Wind blockerThe panoramic roof is equipped with a wind
blocker that folds up when the roof is open.
Related information

Operating the panoramic roof* (p. 173)
Auto closing the panoramic roof* sun curtain
(p. 175)
Pinch protection for windows and sun cur-
tains (p. 166)
Keyless locking and unlocking* (p. 259)
Locking and unlocking using the remote key
(p. 246) Operating the panoramic roof*
The panoramic roof and sun curtain are oper-
ated using a control in the ceiling panel, and
both are equipped with pinch protection.
WARNING Children, other passengers or objects can be
trapped by the moving parts.
Always operate the windows with caution.
Do not allow children to play with the
operating controls.
Never leave a child alone in the vehicle.
Remember to always cut the current to
the power windows by setting the vehi-
cle's electrical system to ignition mode 0
and then taking the remote key with you
when leaving the vehicle.
Never stick objects or body parts out
through the windows, even if the vehicle
electrical system is completely turned off.
CAUTION
Do not open the panoramic roof when
load carriers are installed.
Never place heavy objects on the panor-
amic roof.
CAUTION
Remove ice and snow before opening the
panoramic roof. Be careful not to scratch
any surfaces or damage the trim.
Do not operate the panoramic roof if it is
frozen in place. To operate the panoramic roof and sun curtain,
the ignition must be in mode I or II.
It can also be operated using keyless opening*
with the door handle.
WARNING Make sure that no child or other passenger
comes into contact with the windows as they
are closing with keyless closing*.
CAUTION
Check that the panoramic roof is properly
closed when closing.
The movement of the roof will stop if the control
is released during manual operation or when the
glass has reached the comfort
4
or fully open/
closed position. The movement of both the pan-
oramic roof and the sun curtain is also stopped if
the control in the ceiling is operated again in the 4
The comfort position is a position which helps keep wind and resonance s\
ounds to a comfortably low level.

WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory. 175
Auto operation
1. To open the sun curtain to the fully open
position, pull the control backward to the
auto open mode and release.
2. To open the panoramic roof to the comfort position, pull the control backward a second
time to the automatic opening position and
release.
3. To open the panoramic roof fully, pull the control backward a third time to the auto-
matic opening position and release.
Close by repeating the above procedure in
reverse - push the control forward/down to the
auto close position.
Automatic operation - rapid opening or
closing
The panoramic roof and sun curtain can be
opened or closed simultaneously:
– Open - press the control backward twice to
the automatic operation position and release.
– Close - press the control forward/down twice
to the automatic operation position and
release.
Related information
Panoramic roof* (p. 172)
Auto closing the panoramic roof* sun curtain
(p. 175)
Pinch protection for windows and sun cur-
tains (p. 166)
Keyless locking and unlocking* (p. 259)
Locking and unlocking using the remote key
(p. 246) Auto closing the panoramic roof*
sun curtain
With this function, the sun curtain closes auto-
matically 15 minutes after the car has been
locked if it is parked in hot weather. This is done
to lower the passenger compartment tempera-
ture and protect the upholstery against being
bleached by the sun.
The function is deactivated as the default factory
setting and can be activated or deactivated using
the center display.
1. Tap Settings in the Top view in the center
display.
2.

Tap My Car Locking
.
Select Auto Close Sunroof Curtain to
activate/deactivate.
NOTE The sun curtain also closes when all windows
are closed with keyless closing*.
Related information

Panoramic roof* (p. 172)
Operating the panoramic roof* (p. 173)
Pinch protection for windows and sun cur-
tains (p. 166)

WINDOWS, GLASS AND MIRRORS
* Option/accessory.
176
Keyless locking and unlocking* (p. 259)
Locking and unlocking using the remote key
(p. 246) Wiper blades and washer fluid
The wipers and the washer fluid are used to
improve visibility and the headlight pattern.
The washer nozzles are heated* automatically in
cold weather to prevent the washer fluid from
freezing.
When there is approximately 1 liter (1 qt) of
washer fluid remaining, a message to refill will
appear in the instrument panel.
Related information
Using the rain sensor (p. 177)
Using the windshield and headlight washers
(p. 179)
Using automatic rear window wiping when
backing up (p. 181)
Using the rain sensor's memory function
(p. 178)
Using the rear window wiper/washer
(p. 180)
Filling washer fluid (p. 662)
Windshield wipers in the service position
(p. 661)
Replacing windshield wiper blades (p. 660)
Changing rear window wipers (p. 659)
Using the windshield wipers (p. 176) Using the windshield wipers
The windshield wipers clean the windshield. The
right-side steering wheel lever is used to adjust
windshield wiper settings. Right-hand steering wheel lever.
Thumb wheel, used to set rain sensor sensi-
tivity and interval wiper speed.
Single sweepMove the lever down and release for a
single sweep.
Wipers offMove the lever to position 0 to turn off
the windshield wipers.
Interval wipersSet the number of sweeps per time unit
with the thumb wheel when interval wip-
ers are selected.

SEATS AND STEERING WHEEL
* Option/accessory.
184 Manual front seats
The power front seats can be adjusted in a num-
ber of different ways for optimal comfort and
ergonomics.
Raise/lower the front edge of the seat cush-
ion* by moving the control up/down.
1Change the length of the seat cushion* by
pulling up the lever and moving the cushion
forward/backward. Move the seat forward/backing by lifting the
handle and moving the seat to a suitable dis-
tance from the steering wheel and pedals.
Check to make sure the seat is securely
locked into place after its setting has been
changed. Adjust lumbar support* by pressing the but-
ton up/down/forward/rearward 2
. Raise/lower the seat by moving the control
up/down.
Change the backrest tilt by turning the knob
on the backrest.
WARNING

Do not adjust the seat while driving. The
seat should be adjusted so that the brake
pedal can be depressed fully. In addition,
position the seat as far rearward as com-
fort and control allow.
Check that the seat is securely locked
into position after adjusting.
Related information

Power* front seats (p. 185)
Adjusting the power* front seats (p. 185)
Storing positions for seats, mirrors and head-
up display* (p. 186)
Using stored positions for seats, mirrors and
head-up display* (p. 187)
Adjusting front seat massage settings*
(p. 189)
Adjusting* front seat cushion length (p. 189)
Front seat massage* settings (p. 188)
Adjusting front seat side bolster settings*
(p. 190)
Adjusting front seat lumbar support* (p. 191)
Adjusting the passenger seat from the driv-
er's seat* (p. 192) 1
Only applies to the driver's seat.
2 Applies for four-way lumbar support*. Two-way lumbar support* is adjusted forward/rearward.

SEATS AND STEERING WHEEL
}}
* Option/accessory. 185
Power* front seats
The power front seats can be adjusted in a num-
ber of different ways for optimal comfort and
ergonomics. The power seat can be moved for-
ward/backward and up/down. The height and
length* of the seat cushion and the tilt of the
backrest can be adjusted. Lumbar support* can
be adjusted up, down, forward and backward 3
.
The power seats can be adjusted for a certain
period of time after the door is unlocked without
the engine running. The seats can always be
adjusted while the engine is running. They can
also be adjusted for a short period after the
engine is turned off.
CAUTION The power seats have an overload protector
that is triggered if a seat is blocked by any
object. If this occurs, remove the object and
attempt to adjust the seat again.
Related information

Manual front seats (p. 184)
Adjusting the power* front seats (p. 185)
Storing positions for seats, mirrors and head-
up display* (p. 186)
Using stored positions for seats, mirrors and
head-up display* (p. 187)
Adjusting front seat massage settings*
(p. 189)
Adjusting* front seat cushion length (p. 189)
Front seat massage* settings (p. 188)
Adjusting front seat side bolster settings*
(p. 190)
Adjusting front seat lumbar support* (p. 191)
Adjusting the passenger seat from the driv-
er's seat* (p. 192) Adjusting the power* front seats
Set the desired seating position using the con-
trols on the front seat cushion. To set the con-
venience functions, turn the multifunction con-
trol 4
upward/downward. The illustration shows the controls in a vehicle with four-
way lumbar support*. Vehicles with two-way lumbar sup-
port* do not have the rotary multifunction control. In vehicles with four-way lumbar support*,
turn the multifunction control 4
up/down to
set the convenience functions. In vehicles
with two-way lumbar support*, use the round
button to adjust the lumbar support forward/
rearward. Raise/lower the front edge of the seat cush-
ion by moving the control up/down.
3
Applies for four-way lumbar support*. Two-way lumbar support* is adjusted forward/rearward.

||SEATS AND STEERING WHEEL
* Option/accessory.
190 2.
Select Cushion extension in the seat set-
tings view.
Push in the front part of the four-way but-
ton to extend the seat cushion.
Press the rear part of the four-way button to shorten the seat cushion.
Manually adjusting seat cushion length
Control for adjusting seat cushion.
1.
Grasp the handle on the front of the seat
and pull upward.
2.

Adjust the length of the seat cushion.
3. Release the handle and make sure the seat cushion locks into position.
Related information
Manual front seats (p. 184)
Power* front seats (p. 185)
Adjusting the power* front seats (p. 185)
Storing positions for seats, mirrors and head-
up display* (p. 186)
Using stored positions for seats, mirrors and
head-up display* (p. 187)
Adjusting front seat massage settings*
(p. 189)
Front seat massage* settings (p. 188)
Adjusting front seat side bolster settings*
(p. 190)
Adjusting front seat lumbar support* (p. 191)
Adjusting the passenger seat from the driv-
er's seat* (p. 192) Adjusting front seat side bolster
settings*
Enhance comfort in the front seat by adjusting
the sides of the backrest. Multifunction control, located on the side of the seat
cushion.
The side bolsters in the front seat backrests can
be inflated/deflated to adjust the amount of sup-
port provided. The settings for the multifunctional
seats can be adjusted using either the mutifunc-
tion control on the seat or the center display. The
adjustment settings are shown in the center dis-
play.
To adjust the side bolsters:
1.

Activate the multifunction control by turning
it upward/downward . The seat settings
view will appear in the center display.

SEATS AND STEERING WHEEL
}}
* Option/accessory. 193Move the passenger seat forward/rearward
by moving the control forward/rearward.
Change the backrest tilt of the passenger
seat by moving the control forward/back-
ward.
Related information

Manual front seats (p. 184)
Power* front seats (p. 185)
Adjusting the power* front seats (p. 185)
Storing positions for seats, mirrors and head-
up display* (p. 186)
Using stored positions for seats, mirrors and
head-up display* (p. 187)
Adjusting front seat massage settings*
(p. 189)
Adjusting* front seat cushion length (p. 189)
Front seat massage* settings (p. 188)
Adjusting front seat side bolster settings*
(p. 190)
Adjusting front seat lumbar support* (p. 191) Folding the second row backrests
The second row of seats has three individual
seating positions. The backrests can be folded
down separately.
WARNING
Adjust the seat and ensure it locks into
position before driving. Use caution when
adjusting the seat. Uncontrolled or care-
less adjustments could lead to injury.
Long objects must always be securely
tied down to help prevent injury or dam-
age in the event of sudden braking.
Always turn off the engine and apply the
parking brake when loading or unloading
the vehicle.
Put the gear selector in P to help prevent
the gear selector from being inadvertently
moved.
CAUTION When the backrest is folded down, make sure
there are no objects in the rear seat, and the
seat belts are not buckled. Otherwise there is
a risk of damage to the upholstery.

||SEATS AND STEERING WHEEL
* Option/accessory.
194
CAUTION The seat cushion of the integrated child
restraint* must be in the stowed position
before the center seat backrest can be folded
down.
The armrest* in the center seat must be
raised before the seat backrest is folded
down.
NOTE The front seats may need to be pushed for-
ward and/or the backrest adjusted so that the
rear seat backrests can be fully lowered.
The rear seats may also need to be moved
rearward.
The seats in the second row must be in the
upright position before they can be folded
down completely. They should not be folded
down when they are tilted forward to access
the third row of seats.
Center seat
To fold down the backrest:
1.

Fold down the head restraint manually.
2. Pull the strap on the right side of the center seat.
3. Fold the backrest down until it locks into position. The seat cushion will move down-
ward/forward when the backrest is folded
down and create a flat surface.
To return the backrest to the upright position:
1. Pull the strap.
2. Fold up the backrest and release the strap. Push the backrest until it locks into position.
3. Adjust the head restraint if necessary.
Outboard seats To fold down the backrest:
NOTE
When folding down a second row seat back-
rest, always start from the seat's normal
upright position. Do not use the handle for
folding down the seat when the seat is in the
position for accessing the third row.
1. Pull up and hold the handle on the side of
the seat while the backrest is being folded
down.

SEATS AND STEERING WHEEL
}}
* Option/accessory. 195
2.

Make sure that backrest and head restraint
do not come in contact with the seat in front
while the backrest is being folded down. Fold
the backrest down until it locks into position.
> The seat cushion will move downward/ forward when the backrest is folded down
and create a flat surface. The head
restraint folds down automatically when
the backrest is lowered.
WARNING Make sure the backrest is securely locked
into position after it is folded down.
To return the backrest to the upright position:
1.

Pull up and hold the handle on the side of
the seat while the backrest is being folded
up.
2. Make sure that backrest and head restraint do not come in contact with the seat in front
while the backrest is being folded up. Fold up
the backrest and release the handle.
3. Press the backrest until it locks into position.
4. Fold up the head restraint manually.
WARNING Make sure that the rear seat backrest and
head restraint are locked securely in place
after the seat is folded up.
The head restraints at the outer seats must
always be raised when there is a passenger in
one of these spots of the rear seat.
WARNING
The head restraints on the outboard second-
row seats must always be folded up when
there are passengers in the third row of
seats*.
Related information

Adjusting the second row head restraints
(p. 195)
Moving the second row seats forward/rear-
ward* (p. 197)
Adjusting the second row backrest tilt
(p. 197)
Getting into and out of the third row of
seats* (p. 198)
Folding the third row backrests* (p. 199) Adjusting the second row head
restraints
Adjust the center head restraint in the rear seat
to the seat occupant's height. Fold down the
outboard head restraints* to improve rear visibil-
ity.
Adjusting the center head restraint The center head restraint should be adjusted to
suit the passenger's height. The entire back of
the head should be covered if possible. Manually
move the restraint up or down as needed.

||SEATS AND STEERING WHEEL
* Option/accessory.
196 To lower the restraint, press and hold the button
(located between the backrest and the head
restraint, see illustration) while carefully lowering
the head restraint.
WARNING
The center seat head restraint must be in its
lowest position when the seat is not occupied.
When the center seat is occupied, the head
restraint must be correctly adjusted to the
passenger's height, covering the entire back
of the head if possible.
Electrically folding down the rear seat's
outboard head restraints* The outer head restraints can be folded via the
center display's function view. The head restraint
can be folded down when the vehicle is in igni-
tion mode 0.
Tap the Headrest Fold button
to activate/deactivate folding. Manually push the head restraint until it clicks
into position.WARNING Do not lower the head restraint if there are
passengers in any of the rear seats.
WARNING
The head restraint must be locked in the
upright position after it has been folded up.
WARNING
The head restraints on the outboard second-
row seats must always be folded up when
there are passengers in the third row of
seats*.
Related information

Folding the second row backrests (p. 193)
Moving the second row seats forward/rear-
ward* (p. 197)
Adjusting the second row backrest tilt
(p. 197)
Getting into and out of the third row of
seats* (p. 198)
Folding the third row backrests* (p. 199)