maintenance YAMAHA DT125R 2006 Owner's Guide

1. Gap
7. After tightening the axle holder
nuts, push down hard on the
handlebars several times while
applying the front brake to check
if the front fork compresses and
rebounds smoothly.
8. Connect the speedometer cable.
EAU25080
Rear wheel
EAU25230
To remove the rear wheel
1. Axle retainer bolt
EWA10820
s s
WARNING
It is advisable to have a Yama-
ha dealer service the wheel.
Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Loosen the axle nut.
2. Lift the rear wheel off the ground
according to the procedure on
page 6-26.
1. Axle nut
2. Chain tensioner
3. Remove the swingarm end bolts.
4. Turn the drive chain adjusting
plate on each side of the swin-
garm fully in direction (a).
5. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.
6. Pull the wheel axle out from the
left-hand side, and then remove
the wheel by pulling it back.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-28
112
1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 59

ECA11070
CAUTION
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU25530
To install the rear wheel
1. Install the drive chain onto the
rear sprocket, and then insert the
wheel axle from the left-hand
side.
NOTE:
Make sure that there is enough space
between the brake pads before inser-
ting the brake disc between the brake
pads.
2. Install the drive chain adjusting
plates.
NOTE:
Make sure that the drive chain adjus-
ting plates are installed with the pun-
ched side facing to the outside.
3. Install the swingarm end bolts.4. Adjust the drive chain slack. (See
page 6-19.)
5. Tighten the axle nut and the
swingarm end bolts to the speci-
fied torques, and then install the
cotter pin.
EWA10700
s s
WARNING
Always use a new cotter pin for the
axle nut.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
Swingarm end bolt:
3 Nm (0,3 m•kgf)
EAU25850
Troubleshooting
Although Yamaha motorcycles recei-
ve a thorough inspection before ship-
ment from the factory, trouble may
occur during operation. Any problem
in the fuel, compression, or ignition
systems, for example, can cause poor
starting and loss of power.The following troubleshooting chart
represents a quick and easy procedu-
re for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
1D0-F8199-E2.qxd 20/9/04 11:32 Página 60

EAU25921
Troubleshooting charts
Starting problems or poor engine performanceEWA10840
s s
WARNING
Keep away open flames and do not smoke while checking or working on the fuel system.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
6
Check the fuel level in
the fuel tank.
1. FuelThere is enough fuel.
There is no fuel.Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
Operate the electric starter.
2. CompressionThere is compression.
There is no compression.Check the ignition.
Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.
3. IgnitionWipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
The engine does not start.
Check the battery.
Operate the electric starter.
4. BatteryThe engine turns over
quickly.
The engine turns over
slowly.The battery is good.
Check the battery lead connections,
and charge the battery if necessary.
Dry
WetOpen the throttle halfway and operate
the electric starter.
1D0-F8199-E2.qxd 20/9/04 11:32 Página 61

NOTE:
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended
coolant as soon as possible.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6Wait until the
engine has cooled.Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See NOTE.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
Engine overheatingEWA10400
s s
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the his-
sing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
1D0-F8199-E2.qxd 20/9/04 11:32 Página 62

AAdjusting the autolube pump ..................6-21
Adjusting the brake lever free play ..........6-16
Adjusting the brake pedal position and
free play .................................................6-17
Adjusting the clutch lever free play .........6-15
Adjusting the drive chain slack ................6-20
Adjusting the engine idling speed ...........6-12
Adjusting the rear brake light switch .......6-17
Ajusting the carburetor ............................6-11
Ajusting the throttle cable free play .........6-12
BBrake lever .................................................3-5
Brake pedal ................................................3-5
CCare............................................................7-1
Catalytic converter .....................................3-6
Changing the brake fluid..........................6-19
Checking and lubricating the brake and
shift pedals ............................................6-21
Checking and lubricating the breake and
clutch levers...........................................6-21
Checking and lubricating the cables .......6-21
Checking and lubricating the sidestand ..6-21
Checking and lubricating the throttle grip
and cable ...............................................6-21
Checking the drive chain slack ................6-19
Checking the front and rear brake
pads .......................................................6-18
Checking the front fork ............................6-22
Checking the spark plug ............................6-6
Checking the steering ..............................6-22
Checking the wheel bearings ..................6-23Cleaning the air filter element and check
hose .......................................................6-10
Clutch lever ................................................3-4
Controls and instruments ..........................2-3
Coolant.......................................................6-8
D2-stroke engine oil .....................................3-7
EEngine break-in ..........................................5-2
FFront wheel ..............................................6-26
Fuel cock....................................................3-7
Fuel tank cap .............................................3-5
H
Handlebar switches ...................................3-3
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-10
Indicator and warning lights ......................3-2
LLeft view .....................................................2-1
Lubricating the drive chain ......................6-20
MMain switch/steering lock ..........................3-1
OOwner’s tool kit ..........................................6-1
PParking .......................................................5-3
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear wheel ...............................................6-28Removing and installing cowlings and
panels ......................................................6-5
Replacing the fuse ...................................6-24
Replacing the headlight bulb ...................6-24
Replacing the tail/brake light bulb ...........6-25
Replacing the turn signal light bulb .........6-26
Right view ..................................................2-2
SSeat ............................................................3-8
Shift pedal ..................................................3-4
Shifting .......................................................5-2
Shock absorber..........................................3-9
Sidestand .................................................3-10
Specifications.............................................8-1
Speedometer unit ......................................3-3
Spoke wheels...........................................6-15
Starter (choke) lever ...................................3-8
Starting a cold engine ................................5-1
Starting a warm engine ..............................5-2
Storage.......................................................7-3
Supporting the motorcycle ......................6-26
TTires .........................................................6-13
Transmission oil .........................................6-7
Troubleshooting .......................................6-29
YYEIS handling precautions.........................3-9
YPVS ..........................................................3-9
INDEX
1D0-F8199-E2.qxd 20/9/04 11:32 Página 72