reverse YAMAHA FX HO 2007 User Guide

Operation
72
put until you apply throttle again or you reach
trolling speed.
EJU33290Stopping the watercraft
The watercraft is not equipped with a sepa-
rate braking system. It is stopped by water re-
sistance when the throttle lever is released.
From full speed, the watercraft comes to a
complete stop in approximately 100 m (330 ft)
after the throttle lever is released or the en-
gine is stopped, although this distance will
vary depending on many factors, including
gross weight, water surface conditions, and
wind direction. The watercraft slows down as
soon as the throttle lever is released, but will
coast for a distance before fully stopping. If
you are not sure you can stop in time before
hitting an obstacle, apply throttle and turn in
another direction.
WARNING
EWJ00740

Allow adequate stopping distance.

Take early action to avoid collisions. Re-
member, watercraft and other boats do
not have brakes.

Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft to give you
time to stop.

Do not shut the engine off when slowing
down in case you need engine power tosteer away from a boat or other obstacle
that comes into your path.

Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.
EJU35960Beaching the watercraft
(1) Make sure that there are no boats, swim-
mers, or obstacles near the beach. Re-
lease the throttle lever about 100 m (330
ft) before you reach the intended beach-
ing area.
(2) Approach the beach slowly and stop the
engine before reaching land.
Remember, you need throttle to steer.
(3) Get off the watercraft and pull it up on the
beach.
CAUTION:
ECJ00490
Small pebbles, sand, seaweed, and other
debris can be sucked into the jet intake
and impair or damage the impeller. Always
stop the engine and get off the watercraft
before beaching it.
EJU36060Docking the watercraft
(1) Make sure that there are no boats, swim-
mers, or obstacles near the watercraft.
Reduce speed about 100 m (330 ft) away
from the dock.
(2) Slowly approach the dock and stop the
engine just before coming alongside it.
EJU33320Reverse on waterways
Reverse can be used for slow-speed maneu-
vering when it is necessary to back up out of
tight spots where you cannot turn around. Re-
verse can be used to slow down or stop only
during slow-speed maneuvering, such as
when docking.
UF1X71E0.book Page 72 Tuesday, September 26, 2006 9:52 AM

Operation
73
Once the engine is idling, shift into reverse
and gradually increase engine speed. Make
sure that there are no obstacles or people be-
hind you before shifting into reverse.
EJU33350Rough water operation
The force of landing after jumping can cause
a strong impact on both the watercraft and the
operator and passengers. It is possible for the
operator to hit his or her chest or jaw on the
watercraft or handlebars and be injured. The
passengers could also impact the watercraft
and be injured.
Do not operate the watercraft with your chin
right above the handlebars. In addition, the
operator and passengers should keep their
feet on the floor of the footwell.
Operating in rough water or jumping waves
can also crack the watercraft hull and deck,
and damage internal parts. Avoid operating in
rough water or bad weather conditions.
EJU36361
Post-operation care
To keep your watercraft in top shape, always
take it out of the water after using it and per-
form the following procedures. Leaving the
watercraft in the water for extended periods
will accelerate the rate of normal deterioration
of the jet unit components and hull finish. Ma-
rine organisms and corrosion are some of the
conditions that can adversely affect the life of
many watercraft components.
(1) Remove the watercraft from the water.
(2) Wash down the hull, handlebars, and jet
unit with fresh water.
(3) Remove the seat and check the engine
compartment for water. To drain excess
water, remove the stern drain plugs, and
then raise the bow of the watercraft
enough to allow the water in the bilge to
drain out.
NOTE:
This watercraft is equipped with a jet vacuum
bilge draining system and an electric bilge
draining system that remove water from the
engine compartment while you are underway.
However, some residual water will remain.
(See page 54 for bilge draining procedures.)
(4) Place the watercraft in a horizontal posi-
tion.
UF1X71E0.book Page 73 Tuesday, September 26, 2006 9:52 AM

Operation
75
EJU33461
Transporting
When transporting the watercraft on a trailer,
secure the tie downs to the trailer through the
bow eye and stern eyes.
CAUTION:
ECJ00641

Do not attach ropes or tie downs to any
part of the watercraft other than the bow
eye and stern eyes to secure the water-
craft to the trailer. Otherwise, the water-
craft may be damaged.

Do not route ropes or tie downs over the
seat, as they may leave permanent
marks on the seat’s surface. Also, wrap
the ropes or tie downs with towels or
rags where they touch the body of the
watercraft to avoid scratches or dam-
age.

Before putting the watercraft on the trail-
er or transporting it, be sure to put the
shift lever in the forward position, other-
wise the reverse gate may hit an obsta-
cle, which may cause damage.
UF1X71E0.book Page 75 Tuesday, September 26, 2006 9:52 AM

Maintenance and care
85
EJU34320Checking the jet thrust nozzle angle
Check the handlebars and jet thrust nozzle for
smooth operation.
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust noz-
zle and the nozzle is within specification.
If the steering is stiff or misadjusted, have a
Yamaha dealer service it.
EJU34340Checking the shift cable
Place the shift lever in the reverse position.
Make sure that the reverse gate makes con-
tact with the stopper on the bracket, and thatthe shift arm makes contact with the reverse
gate.
If the reverse gate does not reach the correct
positions, have a Yamaha dealer service it.
EJU34360Checking and adjusting the throttle
cable
Check that the throttle cable moves back to
the set position smoothly and that the throttle
lever free play is within specification.
(1) Squeeze and release the throttle lever. If
the throttle lever does not return smooth-
ly, have a Yamaha dealer service it.
(2) Adjust the free play by loosening the lock-
nut and turning the adjuster. Difference of A and B:
Maximum 5 mm (0.20 in)
1Stopper
2Shift arm
1Locknut
2Adjuster
3Throttle lever free play
Throttle lever free play:
4.0–7.0 mm (0.16–0.28 in)
UF1X71E0.book Page 85 Tuesday, September 26, 2006 9:52 AM

Maintenance and care
88

QSTS cables (pulley end)

QSTS cables (handlebar end)
Remove the QSTS cable housing. Spray a
rust inhibitor into the outer cables. Reinstall
the QSTS cable housing.

Shift cable (shift lever end)

Shift cable (reverse gate end)

Intermediate housing
Fill the intermediate housing with water-re-
sistant grease through the grease nipple
using a grease gun.
EJU34450Checking the battery
Check the level of the battery electrolyte and
make sure that the negative (–) and positive
(+) battery leads are tightened securely.
Grease quantity:
Initial 10 hours or 1 month:
33.0–35.0 cm³ (1.12–1.18 US oz)
(1.16–1.23 Imp.oz)
Every 100 hours or 12 months:
6.0–8.0 cm³ (0.20–0.27 US oz)
(0.21–0.28 Imp.oz)
1Grease nipple
UF1X71E0.book Page 88 Tuesday, September 26, 2006 9:52 AM

Trouble recovery
96
gine. Any wrong connection could dam-
age the electrical system.
(4) Start the engine, and then disconnect the
jumper cables by reversing the steps
above.
CAUTION:
ECJ00690

Never push the start switch while the en-
gine is running.

Do not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not start
in 5 seconds, release the start switch,
wait 15 seconds, and then try again.
EJU34680Replacing the fuses
The fuses are located in the electrical box.
To replace a fuse:
(1) Remove the cap on the electrical box.(2) Replace the blown fuse with the spare
fuse of the correct amperage by using the
fuse puller on the reverse side of the cap.
WARNING
EWJ00800
Do not use fuses of higher amperage than
recommended. Substitution with a fuse
that has an improper rating can cause ex-
1Electrical box
2Cap
3Fuse
4Spare fuse
1Fuse puller
Fuse amperage:
Main fuse:
20 A
Meter fuse:
3 A
Bilge pump fuse:
3 A
UF1X71E0.book Page 96 Tuesday, September 26, 2006 9:52 AM

Index
Lubrication................................................ 77
Lubrication points ..................................... 87
M
Main components, location of .................. 20
Maintenance and adjustments ................. 79
Model information....................................... 2
Multifunction information center ......... 34, 60
O
Oil pressure warning indicator.................. 40
Operating your watercraft......................... 64
Operation ................................................. 61
Operation of controls and
other functions ...................................... 24
Operation requirements ........................... 12
Owner’s/operator’s manual and tool kit .... 80
P
Periodic maintenance chart...................... 81
Post-operation care .................................. 73
Pre-operation check list............................ 51
Pre-operation check points ...................... 53
Pre-operation checks ............................... 51
Primary Identification (PRI-ID) number ...... 1
Pull-up cleats
(for FX Cruiser High Output) ................. 33
Q
Quick Shift Trim System (QSTS) ............. 58
Quick Shift Trim System (QSTS)
selector ................................................. 30
R
Reboarding step ....................................... 32
Recommended equipment ....................... 14
Remote control transmitter ....................... 26
Reverse on waterways ............................. 72
Riding with passengers ............................ 65
Right multifunction display and
operation buttons
(for FX Cruiser High Output) ................. 42
Rough water operation ............................. 73
“RPM” indicator light................................. 36
S
Safe boating rules .................................... 19
Seat storage compartment ....................... 46
Seats ........................................................ 24
Shift cable, checking ................................ 85
Shift lever ................................................. 29Shift lever and reverse gate ..................... 57
Spark plugs, cleaning and adjusting ........ 86
“SPEED” indicator light ............................ 36
Start switch............................................... 27
Starting the engine ................................... 61
Starting the watercraft .............................. 65
Steering system ................................. 28, 57
Stern drain plugs ...................................... 55
Stern eyes ................................................ 33
Stopping the engine ................................. 63
Stopping the watercraft ............................ 72
Storage..................................................... 76
Storage compartments ............................. 45
Submerged watercraft .............................. 97
Switches ................................................... 60
T
Throttle cable, checking and adjusting ..... 85
Throttle lever ...................................... 28, 57
Tilt lever .................................................... 29
Towing the watercraft ............................... 97
Transporting ............................................. 75
Trolling speed, checking .......................... 90
Troubleshooting ....................................... 92
Troubleshooting chart .............................. 92
Turning the watercraft .............................. 70
U
“UNLOCK” indicator light .......................... 37
W
“WARNING” indicator light ....................... 37
Water separator ....................................... 54
Watercraft characteristics ......................... 15
Water-skiing ............................................. 17
Watertight compartment ........................... 47
Y
Yamaha Engine Management
System (YEMS) .................................... 33
Yamaha Security System ......................... 33
Yamaha Security System lock and
unlock modes........................................ 33
UF1X71E0.book Page 2 Tuesday, September 26, 2006 9:52 AM