engine YAMAHA FX HO 2022 Owner's Manual

Watercraft operation
33
EJU40003
Watercraft operation modes
EJU45892Reverse assist
The reverse assist is a function for temporar-
ily increasing the engine speed when moving
in reverse, such as to enter the water
smoothly when launching the watercraft from
a trailer.
This function operates after the engine is
started and only if the watercraft is not shifted
into forward.
TIP
Once the watercraft is shifted into forward af-
ter the engine is started, the reverse assist
cannot be operated.
Activating and deactivating the reverse
assist
The activation of the reverse assist can be
confirmed by the reverse assist indicator on
the multifunction information center.
To activate the reverse assist:
(1) Start the engine.
(2) Squeeze the RiDE lever to the fully openposition, and then push the upper side of
the “SPEED ADJUST” switch. Once the
beeper sounds three times and the re-
verse assist indicator is displayed, the engine speed will increase. The engine
speed can be adjusted to two levels: +1
and +2.
To deactivate the reverse assist:
Perform one of the following operations. The
beeper sounds two times and the reverse as-
sist indicator disappears when the reverse
assist is deactivated.
Relax your grip on the RiDE lever.
Push the lower side of the “SPEED AD-
JUST” switch when the reverse assist level
is set to +1.
Squeeze the throttle lever.EJU45900T.D.E. (thrust directional enhancer)
The T.D.E. is a function for slightly lifting or
lowering the reverse gate from the neutral po-
sition to operate the watercraft at very low
speeds when the engine is running at idling
speed.
1
Reverse assist indicator
2 Reverse assist level
km/h
RPM
x1000
12.7V10 :00AM
Reverse Assist +2
21
1 RiDE lever
1 “SPEED ADJUST” switch
1
1
UF3V73E0.book Page 33 Friday, October 8, 2021 1:30 PM

Watercraft operation
34
This function can be used only when the wa-
tercraft is in neutral.
TIP
While the watercraft is shifted into forward,
the “TRIM/T.D.E.” switch controls the electric
trim system. (See page 31 for information on
the electric trim system.)
Activating and deactivating the T.D.E.
The activation of the T.D.E. can be confirmed
by the T.D.E. indicator on the multifunction
information center.
To activate the T.D.E.:
(1) Shift into neutral.
(2) Push the upper side of the “TRIM/T.D.E.”switch to move forward at a very low
speed or push the lower side of the
“TRIM/T.D.E.” switch to move in reverse
at a very low speed.
TIP
While the T.D.E. is activated, the “N” (neutral)
shift indicator will be displayed and “0” will be
displayed on the speedometer.
To deactivate the T.D.E.:
Perform one of the following operations. The
T.D.E. indicator disappears and the T.D.E. is
deactivated.
Squeeze the throttle lever.
Squeeze the RiDE lever.
Push and hold the “CRUISE/NO WAKE”
switch.
While moving forward at a very low speed,
push the lower side of the “TRIM/T.D.E.”
switch.
While moving in reverse at a very low
speed, push the upper side of the
“TRIM/T.D.E.” switch.
TIP
The T.D.E. is also deactivated when the en-
gine is stopped.
EJU45911No-wake mode
The no-wake mode is a function that main-
tains the engine speed at a fixed setting for
operating the watercraft at low speeds. While
the watercraft is operating in no-wake mode,
the engine speed can be adjusted to one en-
1T.D.E. indicator
2 Forward operation at a very low speed
3 Reverse operation at a very low speed
MPH
RPM
x1000
12.7V10 :00AM
T.D.E. FORWARD
T.D.E. REVERSE T.D.E. FORWARD
1
3
2
1 “TRIM/T.D.E.” switch
1
UF3V73E0.book Page 34 Friday, October 8, 2021 1:30 PM

Watercraft operation
35
gine speed each above and below the initial
engine speed.
This function can be used only when the wa-
tercraft is in neutral, or when the watercraft is
shifted into forward and the engine is operat-
ing at idling speed.
TIP
If the no-wake mode is activated when the
watercraft is in neutral, the watercraft will au-
tomatically shift into forward and the water-
craft will start moving at a low speed.
Activating and deactivating the no-wake
mode
The activation of the no-wake mode can be
confirmed by the no-wake mode indicator on
the multifunction information center.
To activate the no-wake mode:
(1) Shift into neutral, or release the throttlelever and let the engine speed return to
idle.
(2) Push and hold the “CRUISE/NO WAKE” switch. Once the beeper sounds three
times and the no-wake mode indicator is
displayed, the no-wake mode is activat-
ed. (3) Push the upper side or the lower side of
the “SPEED ADJUST” switch to adjust
the engine speed to three settings: “No
Wake –1”, “No Wake” (standard setting),
and “No Wake +1”.
To deactivate the no-wake mode:
Perform one of the following operations. The
beeper sounds two times and the no-wake
mode indicator disappears when the no-
wake mode is deactivated.
Push the “CRUISE/NO WAKE” switch.
Squeeze the throttle lever.
Squeeze the RiDE lever.
TIP
The no-wake mode is also deactivated when
the engine is stopped.
1No-wake mode indicator
2 No-wake mode level
km/h
RPM
x1000
12.7V10 :00AM
No Wake +1
21
1 “CRUISE/NO WAKE” switch
1 “SPEED ADJUST” switch
1
1
UF3V73E0.book Page 35 Friday, October 8, 2021 1:30 PM

Watercraft operation
37
TIP
For acceleration, select from “SLOW”, “ME-
DIUM”, and “FAST”.
Activating the auto trim
The auto trim is activated, the trim angle is
automatically adjusted.
To set auto trim, select “Auto Trim” on the
drive control mode screen.
TIP
For auto trim, select from “Performance” and
“Comfort”.
When auto trim is activated, the trim icon on
the home screen changes color. When auto
trim is set to “Performance”, the “ ” icon is
blue. When auto trim is set to “Comfort”,
the “ ” icon is yellow.
Locking the drive control mode
The drive control mode can be locked.
To lock the drive control mode:
(1) Select the drive control mode indicator.
(2) Select “Unlock”.
(3) Input the 4-digit PIN, and select “ ”.
To unlock the drive control mode:
(1) Select the drive control mode indicator.
(2) Select “Lock”.
(3) Input the 4-digit PIN, and select “ ”.
EJU45930Cruise assist
The cruise assist is a function for maintaining
a desired engine speed within a fixed range
while operating the watercraft. Once the
cruise assist is activated, the set engine
speed can be increased or decreased. How-
ever, the adjustment is limited to a maximum
of five increments above or below the initial
cruise assist setting.
1 Acceleration
1 “Auto Trim”
Auto TrimOff
16FA S Tkm/hONAcceleration
Drive ControlLock
1
Auto TrimOff
16FA S Tkm/hONAcceleration
Drive ControlLock
1
1Unlock
Auto TrimOff
16FA S Tkm/hONAcceleration
Drive ControlUnlock
1
123
456
789
Cancel0
Enter PIN Code
UF3V73E0.book Page 37 Friday, October 8, 2021 1:30 PM

Watercraft operation
38
TIP
The cruise assist can only be set between en-
gine speeds of approximately 3000 r/min and
approximately 7000 r/min.
Activating and deactivating the cruise as-
sist
Activation of the cruise assist can be con-
firmed by the cruise assist indicator on the
multifunction information center.
To activate the cruise assist:
(1) Operate the throttle lever until the de-sired engine speed is reached.
(2) When the engine speed reaches the de- sired cruise assist setting, push the
“CRUISE/NO WAKE” switch. Once the
beeper sounds three times and the
cruise assist indicator is displayed, the
cruise assist is activated. (3) When the cruise assist is activated, slow-
ly squeeze the throttle lever to keep it
squeezed further than the position at
which the cruise assist was set.
TIP
Check the multifunction information center to
make sure that the cruise assist is activated
before squeezing the throttle lever to the full
throttle position. If the cruise assist is not ac-
tivated, the engine will respond normally to
the throttle operation.
(4) Once the cruise assist is activated, pushthe upper side of the “SPEED ADJUST”
switch to increase the set engine speed
or the lower side of the “SPEED AD-
JUST” switch to decrease the set engine
speed. The engine speed can be
changed in the range of the cruise assist
levels –5 to +5.
1Cruise assist indicator
2 Cruise assist level
km/h
RPM
x1000
12.7V10 :00AM
Cruise Assist +4
21
1 “CRUISE/NO WAKE” switch
1
UF3V73E0.book Page 38 Friday, October 8, 2021 1:30 PM

Watercraft operation
39
TIP
Because the cruise assist can only be set be-
tween engine speeds of approximately 3000
r/min and approximately 7000 r/min, the
cruise assist level cannot be adjusted to an
engine speed outside of this range.
To deactivate the cruise assist:
Relax your grip on the throttle lever past the
position at which the cruise assist was set.
The beeper sounds two times and the cruise
assist indicator disappears when the cruise
assist is deactivated.
1“SPEED ADJUST” switch
1
UF3V73E0.book Page 39 Friday, October 8, 2021 1:30 PM

Instrument operation
40
EJU46620
Multifunction information center
The multifunction information center displays
various watercraft information.
The multifunction information center is a
touch screen that you can touch directly to
turn the various functions on or off or change
settings. You can also perform operations
using the touchpad control.
The language and display units shown can be
changed. (See page 55 for information on
changing the language and display units.) In
the illustrations in this manual, English is used
for the language and US units are used for the
display units.
EWJ01980
For safety, do not touch the multifunction
information center while the watercraft is
moving. Otherwise, you could lose control
of the watercraft, which may lead to an ac-
cident.
TIP
The multifunction information center does not
receive operation input while the watercraft is
moving. Before operating the multifunction
information center, stop the watercraft and
check the area around you to make sure it is
safe to operate the center.
Turning on the multifunction information
center
When the engine start/stop switch is pushed,
the multifunction information center turns on.
After the logo is displayed for a few seconds
followed by a disclaimer, select “CONFIRM”
to display the home screen.
TIP
The multifunction information center is turned
on, even if the engine start/stop switch is also
pushed briefly.
Turning off the multifunction information
center
If no operations are performed for about 50
seconds after the engine stops, a message
appears on the multifunction information
center. Select “Shutdown” on the displayed
message to turn off the multifunction infor-
mation center.
TIP
If there is no operation input within 20 sec-
onds after the message is displayed, the mul-
tifunction information center turns off.
Turning accessory mode on and off
When accessory mode is turned on, the mul-
tifunction information center can be operated
even if the engine is stopped.
To turn on accessory mode, select “Contin-
ue” on the message that appears on the me-
ter after the engine stops.
1 “Shutdown”
ContinueShutdown
Entering Accessory Mode
Engine is off. Vehicle will now be draining battery power.
Would you like to continue? If no selection is made, vehicle will shutdown.
1
UF3V73E0.book Page 40 Friday, October 8, 2021 1:30 PM

Instrument operation
41
To turn off accessory mode, select the ac-
cessory mode button displayed on the home
screen, and select “Shutdown” on the mes-
sage that appears.
TIP
The message is displayed on the multi-
function information center even if there is
no operation for about 50 seconds after the
engine stops.
Accessory mode will drain power from the
battery. To save power for starting the en-
gine, the multifunction information center
may turn off even when accessory mode is
running.
EJU46630Operation buttons
This model is equipped with a touchpad con-
trol to operate the multifunction information
center.D-pad
Operate the d-pad to switch or select
screens for each item.
Operate the d-pad to show the selected item
in red.
“BACK” button
Push this button to go back to the previous
screen.
Push and hold the “BACK” button to display
the home screen.
“OK” button
Push this button to choose the currently se-
lected item.
1
“Continue”
1 Accessory mode button
ContinueShutdown
Entering Accessory Mode
Engine is off. Vehicle will now be draining battery power.
Would you like to continue? If no selection is made, vehicle will shutdown.
1
Auto TrimOff
12.7V2
1
1D-pad
2 “BACK” button
3 “OK” button
1
23
UF3V73E0.book Page 41 Friday, October 8, 2021 1:30 PM

Instrument operation
44
EJU46662
Home screen “ ”
The center display of the home screen dis-
plays the speedometer, tachometer, and in-
dicator that shows the operation of the
cruising mode. (See page 33 for information
on the functions of the various modes.)
Tachometer
The tachometer shows the engine speed us-
ing the numbers ×1000 RPM (r/min) and the
number of display segments.
TIP
While the engine is starting, the tachometer is
also displayed in the lower left of screens oth-
er than the home screen.
Speedometer
The speedometer shows the watercraft
speed.
TIP
The display units of the speedometer are
selected according to the display units of
the multifunction information center. (See
page 55 for information on switching the
display units.)
When operating the watercraft in reverse,
or when moving forward or in reverse at a
very low speed using the T.D.E., “0” will be
displayed on the speedometer.
If the GPS is not operating correctly, the
speedometer cannot display a number.
While the engine is starting, the speedom-
eter is also displayed in the lower left of
screens other than the home screen.
1Tachometer
2 Speedometer
3 Reverse assist indicator
4 T.D.E. indicator
5 No-wake mode indicator
6 Cruise assist indicator
km/h
RPM
x1000
No Wake +1 T.D.E. Forward
Cruise Assist +4 Reverse Assist +2
12
5
4
6
3
1 Tachometer
1 Speedometer
KM/Hx1000 RPM12.7V
1
KM/Hx1000 RPM12.7V
1
UF3V73E0.book Page 44 Friday, October 8, 2021 1:30 PM

Instrument operation
52
To lock or unlock the GeoFence, select
“Lock” or “Unlock” and enter the PIN code.
TIP
If the GeoFence is locked, you cannot acti-
vate or stop the operation of the “GeoFence”
function or edit the GeoFence radius.
EJU46711Map settings “ ”
Map settings can be displayed on the setting
menu screen by selecting “ ” from the
“overflow menu” on the map screen. See
page 59 for detailed information on map set-
tings.
EJU46721
Information screen “ ”
The information screens show the trip infor-
mation and fuel information in the center dis-
play. Displayed items are as follows.
“Trip Time”
“Trip Distance”
“Fuel Average”
“Fuel Used”
“Fuel Rate”
“Engine Hours”
TIP
The display units for the distances and fuel
amounts are selected according to the dis-
play units of the multifunction information
center. (See page 55 for information on
switching the display units.)
1“Save”
W
GeoFenceCancelSave
W3.2 kmFence
1
Trip Information
Trip Time:Hrs0.0
Trip Distance:km1.1
Fuel Average:km/L0.0
Fuel Used00
UF3V73E0.book Page 52 Friday, October 8, 2021 1:30 PM