fuel YAMAHA GP1300R 2007 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2007, Model line: GP1300R, Model: YAMAHA GP1300R 2007Pages: 90, PDF Size: 5.78 MB
Page 38 of 90
Features and functions
31
speeds. If this occurs, the “WARNING” light
and the engine overheat warning indicator
come on and the buzzer sounds continuously.
In addition, the warning system will cut the ig-
nition to the engine to reduce the risk of se-
vere overheating. The engine cannot be
started until it cools down, so it may be neces-
sary to have the watercraft towed back to the
shore. (See “Towing the watercraft” on page
78 for towing procedures.)
The warning signals will be cleared when the
engine is restarted after it has cooled down.
NOTE:
If multiple warnings occur at the same time,
their priority is as follows:
(1) Final engine overheat warning
(2) Fuel level warning
(3) Oil level warning
(4) Initial engine overheat warning
(5) Exhaust temperature warning
(6) Check engine warning
EJU31610Exhaust temperature warning indicator
This model is equipped with an exhaust tem-
perature warning system.
If the exhaust temperature becomes too hot,
the “WARNING” light and the exhaust tem-
perature warning indicator begin to blink, and
the buzzer sounds intermittently.If this occurs, reduce the engine speed and
return to shore to allow the exhaust system to
cool down.
WARNING
EWJ00830
Do not touch the hot muffler or catalytic
converter during or immediately after en-
gine operation; they can cause serious
burns. In addition, the catalytic converter
becomes hotter after the engine stops be-
fore cooling down.
CAUTION:
ECJ00810
This model is equipped with a catalytic
converter.
If the “WARNING” light, exhaust temper-
ature warning indicator, and buzzer
come on, reduce the engine speed (be-
low 4000 r/min) and return to shore.
If you cannot locate and correct the
cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe en-
gine damage.
The warning signals will be cleared when the
engine is restarted after it has cooled down.
EJU31630Check engine warning indicator
If a sensor malfunction or a short circuit is de-
tected, the “WARNING” light and the check
UF1G74E0.book Page 31 Monday, July 31, 2006 10:10 AM
Page 42 of 90
Operation
35
EJU31800
Fuel and oil
This engine uses Yamaha’s oil injection sys-
tem, which provides superior lubrication by
ensuring the proper fuel-to-oil ratio for all op-
erating conditions. No fuel premixing is nec-
essary, except during the engine break-in
period. Simply pour gasoline into the fuel tank
and oil into the oil tank.
The engine utilizes an electronic fuel injection
system to deliver the optimal air-fuel ratio re-
quired by the engine. By ensuring the optimal
combustion conditions, this system is able to
increase startability and improve fuel econo-
my.
EJU31850Gasoline
WARNING
EWJ00440
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!
Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.
Stop the engine before refueling.
Refuel in a well-ventilated area with the
watercraft in a horizontal position.
Do not stand or sit on the watercraft
while refueling in case of fire.
Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.
Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated areawith the watercraft in a horizontal posi-
tion.
Tighten the fuel tank filler cap securely
after refueling.
If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.
If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
CAUTION:
ECJ00320
Do not use leaded gasoline. Leaded gas-
oline can seriously damage the catalytic
converter.
Use only fresh gasoline that has been
stored in clean containers.
EJU31860Gasohol
There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets the minimum octane ratings.
Gasohol containing methanol is not recom-
mended by Yamaha because it can cause
fuel system damage and engine performance
problems.Recommended gasoline:
Regular unleaded gasoline with a mini-
mum octane rating of
86 (Pump octane number) = (R +
M)/2
90 (Research octane number)
UF1G74E0.book Page 35 Monday, July 31, 2006 10:10 AM
Page 43 of 90
Operation
36
EJU318802-stroke engine oil
CAUTION:
ECJ00270
Use only YAMALUBE 2-W engine oil, oth-
erwise the catalytic converter and other
engine components could be seriously
damaged.
NOTE:
YAMALUBE 2-W engine oil is developed for
this watercraft and available from a Yamaha
dealer.
EJU31920Filling the fuel tank
CAUTION:
ECJ00290
Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.
(1) Open the hood, remove the front storage
compartment, and then check the fuel
level. (See “Front storage compartment”
on page 32 for more information.)
(2) Remove the fuel tank filler cap, and then
slowly add fuel to the fuel tank. Stop fillingwhen the fuel level just reaches the bot-
tom of the filler tube.
(3) Install the fuel tank filler cap and front
storage compartment, and then close the
hood.
NOTE:
Do not fill up the filler tube because fuel ex-
pands as it warms up and could overflow.
EJU31960Filling the oil tank
WARNING
EWJ00420
Do not add gasoline to the oil tank. Fire
or explosion could result.
Oil in the bilge is a serious fire hazard.
Wipe up any spilled oil immediately.
CAUTION:
ECJ00300
Do not allow the oil tank to become com-
pletely empty. If the oil tank becomes emp-
ty, the oil pump must be bled to ensure
proper oil flow, otherwise engine damage
could result. If necessary, have a Yamaha
dealer bleed the oil pump.
(1) Remove the seat to view the oil level.
(See page 21 for seat removal and instal-
lation procedures.) Recommended engine oil:
YAMALUBE 2-W
Fuel tank capacity:
60.0 L (15.9 US gal) (13.2 Imp.gal)
UF1G74E0.book Page 36 Monday, July 31, 2006 10:10 AM
Page 45 of 90
Operation
38
EJU31980
Pre-operation checks EJU31990Pre-operation check list
Before operating this watercraft, perform the checks in the following check list. See the accom-
panying text in this chapter for details on how to perform the checks.
WARNING
EWJ00410
If any item in the pre-operation check list is not working properly, have it inspected and
repaired before operating the watercraft, otherwise an accident could occur.
NOTE:
Pre-operation checks should be made each time the watercraft is used. These checks can be
completed in a short time. It is worth the time spent to ensure safety and reliability.
ITEM ROUTINE PAGE
BEFORE LAUNCH OR OPERATION
Engine compartmentRemove the seat and front storage compartment to
ventilate the engine compartment. Check for fuel va-
pors and loose electrical connections.39
BilgeCheck for water and fuel and drain if necessary. 39
Stern drain plugsCheck for proper installation. 40
Throttle leverCheck that the throttle lever springs back smoothly. 42
Steering systemCheck for proper operation. 42
QSTSCheck for proper operation. 42
Fuel and oilCheck the fuel and oil levels and replenish if neces-
sary.
Check the hoses and tanks for leakage.39
Water separatorCheck for water and drain if necessary. 39
BatteryCheck the electrolyte level and battery condition. 40
HoodCheck that the hood is securely closed. 21
SeatCheck that the seat is securely installed. 21
Hull and deckCheck the hull and deck for cracks and other dam-
age.39
Jet intakeCheck for debris and remove if necessary. 43
Fire extinguisherCheck the condition and replace if necessary. 41
Engine shut-off cordCheck the condition and replace if frayed or broken. 44
SwitchesCheck the start switch, engine stop switch, and en-
gine shut-off switch for proper operation.44
AFTER LAUNCH
Cooling water pilot outletCheck that water is discharged while the engine is
running and the watercraft is in the water.44
Multifunction information
centerCheck for warning indications and proper operation. 44
UF1G74E0.book Page 38 Monday, July 31, 2006 10:10 AM
Page 46 of 90
Operation
39
EJU32280Pre-operation check points EJU32300Engine compartment
Ventilate the engine compartment before
each use.
To ventilate the engine compartment, remove
the seat and front storage compartment. (See
“Seat” on page 21 and “Front storage com-
partment” on page 32 for more information.)
Leave the engine compartment open for a few
minutes to allow any fuel vapors to escape.
While the engine compartment is open, check
for loose electrical connections.
WARNING
EWJ00460
Failure to ventilate the engine compart-
ment could result in a fire or explosion. Do
not start the engine if there is a fuel leak or
a loose electrical connection.
EJU32350Hull and deck
Check the hull and deck for cracks and other
damage. If any damage is found, have a
Yamaha dealer repair the watercraft.
EJU32371Fuel and oil systems
Check the fuel system for leakage, cracks,
and malfunctions before each use. (See page
66 for check points and correct procedures.)
(1) Remove the fuel tank filler cap to release
any pressure that might have built up in
the fuel tank.(2) Remove the seat and front storage com-
partment. (See “Seat” on page 21 and
“Front storage compartment” on page 32
for more information.)
(3) Check the fuel and oil levels in the tanks
and replenish if necessary. (See page 36
for refueling procedures and page 36 for
oil tank filling procedures.)
(4) Install the fuel tank filler cap, seat, and
front storage compartment.
EJU32420Water separator
Check the water separator for water. The wa-
ter separator retains any water that may have
entered through the fuel tank breather hose if
the watercraft was capsized. Normally, the
water separator is empty.
If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to in-
stall the drain screw after draining the water
separator.
EJU32440Bilge
Check the bilge for moisture and fuel residue.
This watercraft is equipped with a convention-
al jet vacuum bilge draining system and an
1Water separator
2Drain screw
UF1G74E0.book Page 39 Monday, July 31, 2006 10:10 AM
Page 52 of 90
Operation
45
tion on proper operation of the multifunction
information center.)EJU32740
Operation
WARNING
EWJ00510
Before operating your watercraft, become
familiar with all of the controls. Consult a
Yamaha dealer about any control or func-
tion that you do not fully understand. Fail-
ure to understand how the controls work
could cause an accident or prevent you
from avoiding an accident.
CAUTION:
ECJ00460
Make sure that the stern drain plugs are
tightened securely before launching the
watercraft.
EJU32760Engine break-in
The engine break-in period is essential to al-
low the various components of the engine to
wear and polish themselves to the correct op-
erating clearances. This ensures proper per-
formance and promotes longer component
life.
CAUTION:
ECJ00450
For the first tankful of fuel, premix the
fuel in a fuel-to-oil ratio of 50:1 (in addi-
tion to the oil in the oil tank).
After break-in, use straight gasoline for
normal operation.
UF1G74E0.book Page 45 Monday, July 31, 2006 10:10 AM
Page 53 of 90
Operation
46
(1) Launch the watercraft and start the en-
gine. (See page 46 for engine starting
procedures.)
(2) Run the engine at trolling speed for 5 min-
utes.
(3) Gradually apply throttle and run the en-
gine at 5000 r/min or less.
(4) Operate the watercraft at 5000 r/min or
less for the first tankful of fuel.
(5) Fill the fuel tank with straight gasoline,
and then proceed with normal operation.
CAUTION:
ECJ00430
Failure to follow the engine break-in pro-
cedure could result in reduced engine life
or even severe engine damage.
EJU32820Launching the watercraft
When launching the watercraft, make sure
that there are no obstacles around you.
After the watercraft is in the water, turn it
around so that the bow faces the direction you
wish to go. Start the engine, and then slowly
move away from the launching area. If there
are waves, someone should make sure that
the watercraft is not pushed into the trailer af-
ter launching the watercraft.
EJU32840Starting the engine
WARNING
EWJ00560
Never start the engine or let it run for any
length of time in an enclosed area. Ex-
haust fumes contain carbon monoxide, a
colorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.
(1) Launch the watercraft in water free from
weeds and debris and at least 60 cm (2 ft)
deep.
WARNING
EWJ00570
Never operate in water that is less than 60
cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged ob-
ject, which could result in injury.
CAUTION:
ECJ00470
Never operate in water that is less than 60
cm (2 ft) deep, otherwise pebbles or sand
could be sucked into the jet intake, caus-
ing impeller damage and engine overheat-
ing.
UF1G74E0.book Page 46 Monday, July 31, 2006 10:10 AM
Page 67 of 90
Maintenance and care
60
EJU33490
Storage
WARNING
EWJ00330
Always place the watercraft upright in a
horizontal position when storing it, other-
wise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
Storage for long periods of time, such as win-
ter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
EJU33520Flushing the cooling system
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
WARNING
EWJ00270
Do not start the engine on land if anyone is
behind the watercraft. Hot water and
steam spurting from the exhaust outlet
into the air can cause serious burns.
CAUTION:
ECJ00130
Do not supply water to the cooling water
passages when the engine is not run-
ning. The water could flow back through
the muffler into the crankcase, causing
severe engine damage.
Do not run the engine for more than 15
seconds on land without supplying wa-
ter, otherwise the engine could over-
heat.
Do not run the engine over 4000 r/min on
land, otherwise the catalytic converter
could be seriously damaged.
(1) Remove the watercraft from the water
and place it in a horizontal position.(2) Remove the flushing hose connector
cap, and then insert the garden hose
adapter into the flushing hose connector
and turn it until it is securely connected.
(3) Connect the garden hose adapter to a
water tap using a garden hose.
NOTE:
A garden hose is not included and must be
purchased separately.
(4) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the cooling water pi-
lot outlet.
(5) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps.
(6) Turn the water supply off, and then force
the remaining water out of the cooling
water passages by running the engine at
4000 r/min or less for 10 to 15 seconds.
(7) Stop the engine.
(8) Remove the garden hose adapter and in-
stall the flushing hose connector cap.
1Flushing hose connector cap
2Garden hose adapter
3Flushing hose connector
UF1G74E0.book Page 60 Monday, July 31, 2006 10:10 AM
Page 68 of 90
Maintenance and care
61
EJU33580Lubrication
WARNING
EWJ00260
Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.
(1) Remove the spark plugs and pour ap-
proximately one tablespoon of engine oil
into each cylinder.
(2) Grease the spark plug threads and rein-
stall the spark plugs.
(3) With the spark plug caps removed from
the spark plugs, crank the engine for 3
seconds or less using the start switch.
(4) Lubricate all cables such as the throttle
and steering cables.
NOTE:
Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.
(5) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
68.
EJU33651Fuel system
WARNING
EWJ00290
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!
Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.
Stop the engine before refueling.
Refuel in a well-ventilated area with the
watercraft in a horizontal position.
Do not stand or sit on the watercraft
while refueling in case of fire.
Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.
Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated area
with the watercraft in a horizontal posi-
tion.
Tighten the fuel tank filler cap securely
after refueling.
If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.
If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
Top off the fuel tank with fresh gasoline and
add 470 ml (15.9 US oz, 16.5 Imp oz) of
Yamaha Fuel Stabilizer and Conditioner.
CAUTION:
ECJ00140
Use only Yamaha Fuel Stabilizer and Con-
ditioner, otherwise the catalytic converter
could be seriously damaged.
EJU33680Battery
If the watercraft will not be used for more than
a month, remove the battery from the water-
craft and store it in a cool, dry place.
(1) Disconnect the negative (–) battery lead
first, then the positive (+) battery lead and
breather hose, and then remove the bat-
tery from the watercraft.
UF1G74E0.book Page 61 Monday, July 31, 2006 10:10 AM
Page 72 of 90
Maintenance and care
65
EJU33820Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, maintenance
may need to be performed more frequently depending on your operating conditions.
This “” mark indicates maintenance that you may do yourself.
This “” mark indicates work to be done by a Yamaha dealer.
* This operation should be performed after every use.
Item OperationInitial Thereafter every
Page 10
hours50
hours100
hours100
hours200
hours
6
months12
months12
months24
months
Spark plugsCheck, clean, adjust 67
Lubrication pointsLubricate 68
Intermediate hous-
ingLubricate 68
Fuel systemCheck 66
Fuel tankCheck, clean 66
Oil injection sys-
temCheck, clean 66
Throttle shaftCheck—
Cooling water pas-
sagesFlush
*60
Water inlet strain-
erCheck, clean—
Bilge strainerClean—
Electric bilge
pump strainerCheck, clean—
ImpellerCheck—
Jet thrust nozzle
angleCheck, adjust 66
QSTS mechanismCheck, adjust—
Throttle cableCheck, adjust 67
Stern drain plugsCheck, replace 40
BatteryCheck, charge 69
Rubber couplingCheck—
Engine mountCheck—
Nuts and boltsCheck—
UF1G74E0.book Page 65 Monday, July 31, 2006 10:10 AM