oil filter YAMAHA GRIZZLY 250 2010 Owners Manual

Operating the drive select lever and
driving in reverse ...................................... 6-3
Shifting ....................................................... 6-4
Engine break-in .......................................... 6-6
Parking ....................................................... 6-7
Parking on a slope ..................................... 6-7
Accessories and loading ............................ 6-8
RIDING YOUR ATV ...................................... 7-1
GETTING TO KNOW YOUR ATV............... 7-2
RIDE WITH CARE AND GOOD
JUDGMENT .............................................. 7-2
BE CAREFUL WHERE YOU RIDE ............. 7-9
TURNING YOUR ATV .............................. 7-12
CLIMBING UPHILL ................................... 7-14
RIDING DOWNHILL.................................. 7-16
CROSSING A SLOPE............................... 7-17
CROSSING THROUGH SHALLOW
WATER ................................................... 7-18
RIDING OVER ROUGH TERRAIN ........... 7-20
SLIDING AND SKIDDING ......................... 7-21
WHAT TO DO IF... .................................... 7-22
WHAT TO DO... ........................................ 7-22
PERIODIC MAINTENANCE AND
ADJUSTMENT ............................................... 8-1
Owner’s manual and tool kit ....................... 8-1Periodic maintenance chart for
the emission control system .....................8-3
General maintenance and lubrication
chart ..........................................................8-5
Checking the spark plug .............................8-9
Engine oil and oil filter element .................8-11
Final gear oil .............................................8-17
Cleaning the air filter element ...................8-20
Cleaning the spark arrester ......................8-23
Adjusting the carburetor ............................8-25
Adjusting the engine idling speed .............8-25
Adjusting the throttle cable free play .........8-26
Valve clearance ........................................8-27
Adjusting the drive select lever safety
system cable ...........................................8-27
Brakes .......................................................8-27
Checking the front brake pads and rear
brake shoes ............................................8-27
Checking the brake fluid level ...................8-29
Changing the brake fluid ...........................8-29
Checking the front brake lever free play ...8-30
Adjusting the brake pedal position, free
play and the rear brake lever free play ...8-30
Brake light switches ..................................8-33
Adjusting the clutch free play ....................8-34
Checking and lubricating the cables .........8-35
U1P065E0.book Page 2 Monday, August 31, 2009 1:10 PM

3-1
3
EBU17680
DESCRIPTION
EBU17690Left view
EBU17700Right view
1. Headlights
2. Fuel cock
3. Recoil starter
4. Fuses
5. Battery
6. Tail/brake light
7. Rear shock absorber assembly spring preload adjusting
ring
8. Engine oil drain bolt
9. Shift pedal
9
1. Spark arrester
2. Storage compartment and tool kit
3. Air filter case
4. Engine oil filler cap
5. Brake pedal
6. Clutch adjusting screw
7. Oil filter element
8. Rear brake light switch
5
1234
6 7 8
U1P065E0.book Page 1 Monday, August 31, 2009 1:10 PM

8-7
8
14 Engine oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√ √√√
15Engine oil filter ele-
mentClean or replace if necessary.√√√
16 Engine oil strainerClean.√√√
17 Final gear oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√√
18*Moving parts and
cablesLubricate.√√√√
19*Drive select lever
safety system cableCheck operation and adjust or replace if neces-
sary.√√√
20*Throttle lever hous-
ing and cableCheck operation and correct if necessary.
Check throttle cable free play and adjust if neces-
sary.
Lubricate throttle lever housing and cable.√√√√√
21*Front and rear brake
switchesCheck operation and correct if necessary.√√√√√
22*Lights and switchesCheck operation and correct if necessary.
Adjust headlight beams.√√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1300
(800)2500
(1600)2500
(1600)5000
(3200)
hours 20 80 160 160 320U1P065E0.book Page 7 Monday, August 31, 2009 1:10 PM

8-11
8
TIPIf a torque wrench is not available when installing
the spark plug, a good estimate of the correct
torque is 1/4–1/2 turn past finger tight. However,
the spark plug should be tightened to the specified
torque as soon as possible.3. Install the spark plug cap.EBU2329FEngine oil and oil filter element The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter element cleaned at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
To check the engine oil level
1. Place the ATV on a level surface.
2. Check the engine oil level on a cold engine.
TIPIf the engine was started before checking the oil
level, be sure to warm up the engine sufficiently,
and then wait at least ten minutes until the oil set-
tles for an accurate reading.3. Remove the engine oil filler cap, and then
wipe the engine oil dipstick off with a clean
rag.
4. Insert the dipstick into the filler hole (without
screwing it in), and then remove it again to
check the oil level.TIPThe engine oil should be between the minimum
and maximum level marks.
Tightening torque:
Spark plug:
17.5 Nm (1.75 m·kgf, 12.7 ft·lbf)
U1P065E0.book Page 11 Monday, August 31, 2009 1:10 PM

8-13
8
TIPSkip steps 5–11, 16, and 17 if the oil filter element
is not being cleaned.5. Remove the footboard by removing the bolts.6. Fully loosen the brake pedal free play adjust-
ing nut, and push the brake pedal downward.1. Engine oil drain bolt
2. O-ring
3. Compression spring
4. Oil strainer
1. Footboard
2. Bolt
U1P065E0.book Page 13 Monday, August 31, 2009 1:10 PM

8-14
8 7. Move the drive select lever safety system ca-
ble away from the oil filter element cover.8. Remove the oil filter element cover by remov-
ing the bolts, and then remove the oil filter el-
ement and the O-ring. NOTICE: Do not
loosen the adjusting nuts shown when re-
moving the oil filter element cover or oil fil-
ter element.
[ECB00341]
1. Brake pedal free play adjusting nut
1. Drive select lever safety system cable
2. Oil filter element cover
12
U1P065E0.book Page 14 Monday, August 31, 2009 1:10 PM

8-15
89. Clean the oil strainer and oil filter element with
solvent.10. Install the oil filter element and a new O-ring.
TIPMake sure that the O-ring is properly seated.11. Install the oil filter element cover by installing
the bolts, and then tighten them to the speci-
fied torque.
1. Adjusting nut
2. Oil filter element cover
3. Bolt
12
3
3
1. Oil filter element
2. O-ringTightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
U1P065E0.book Page 15 Monday, August 31, 2009 1:10 PM

8-16
8 12. Install the oil strainer, the compression spring,
a new O-ring and the engine oil drain bolt, and
then tighten the engine oil drain bolt to the
specified torque. NOTICE: Before installing
the engine oil drain bolt, be sure to install
the O-ring, compression spring and oil
strainer.
[ECB00321]
13. Refill with the specified amount of the recom-
mended engine oil, and then install and tight-
en the engine oil filler cap.
TIPBe sure to wipe off spilled oil on any parts after the
engine and exhaust system have cooled down.NOTICEECB00300
In order to prevent clutch slippage (since the
engine oil also lubricates the clutch), do not
mix any chemical additives. Do not use oils
with a diesel specification of “CD” or oils of
a higher quality than specified. In addition,
do not use oils labeled “ENERGY CONSERV-
ING II” or higher.
Make sure that no foreign material enters the
crankcase.14. Start the engine, and then let it idle for several
minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.
15. Turn the engine off, wait at least ten minutes,
and then check the oil level and correct it if
necessary.
16. Install the footboard by installing the bolts, and
then tighten them to the specified torques. Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
Recommended oil:
See page 10-1.
Oil quantity:
Without oil filter element removal:
1.50 L (1.59 US qt, 1.32 Imp.qt)
With oil filter element removal:
1.60 L (1.69 US qt, 1.41 Imp.qt)
U1P065E0.book Page 16 Monday, August 31, 2009 1:10 PM

8-20
8 9. Check the final gear case for oil leakage. If oil
is leaking, check for the cause.
10. Install the final gear case guard by installing
the bolts and tightening them to the specified
torque.
EBU23686Cleaning the air filter element The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.TIPThere is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.
1. Place the ATV on a level surface.
2. Remove the seat. (See page 4-11.)
3. Remove the air filter case cover by unhooking
the holders. Tightening torque:
Final gear case guard bolt:
17 Nm (1.7 m·kgf, 12 ft·lbf)1. Air filter case check hose
U1P065E0.book Page 20 Monday, August 31, 2009 1:10 PM

8-22
8 6. Clean the sponge material with water or sol-
vent. WARNING! When using solvent to
clean the sponge material, always use
parts cleaning solvent or water. Never use
low-flash-point solvents or gasoline to
clean the sponge material because the en-
gine could catch fire or explode.
[EWB01951]
7. Squeeze the excess water or solvent out of
the sponge material and let it dry. NOTICE:
Do not twist the sponge material when
squeezing it. Do not apply oil to the
sponge material.
[ECB00471]
8. Check the sponge material and replace it if
damaged.
9. Tap the air filter element lightly to remove
most of the dust and dirt. Blow out the remain-
ing dirt with compressed air as shown. If the
air filter element is damaged, replace it.
1. Air filter element
2. Sponge materialU1P065E0.book Page 22 Monday, August 31, 2009 1:10 PM