wheel YAMAHA KODIAK 700 2017 Owner's Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2017, Model line: KODIAK 700, Model: YAMAHA KODIAK 700 2017Pages: 178, PDF Size: 4.61 MB
Page 161 of 178
8-65
8
2. Lower the ATV to the ground.
3. Tighten the wheel nuts to the specified
torques.
EBU25741TroubleshootingAlthough Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the
fuel, compression, or ignition systems, for exam-
ple, can cause poor starting and loss of power.
The following troubleshooting charts represent
quick and easy procedures for checking these vi-
tal systems yourself. However, should your ATV
require any repair, take it to a Yamaha dealer,
whose skilled technicians have the necessary
tools, experience, and know-how to service the
ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWB02281Do not smoke when checking the fuel system.
Fuel can ignite or explode, causing severe inju-
ry or property damage. Make sure there are no
open flames or sparks in the area, including pi-
lot lights from water heaters or furnaces.
1. Tapered nutTightening torques:Front wheel nut:55 N·m (5.5 kgf·m, 40 lb·ft)
Rear wheel nut: 55 N·m (5.5 kgf·m, 40 lb·ft)1
UB1661E0.book Page 65 Thursday, May 12, 2016 2:47 PM
Page 164 of 178
9-1
9
EBU25861
CLEANING AND STORAGE
EBU25882CleaningFrequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.1. Before cleaning the ATV: a. Block off the end of the exhaust pipe toprevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps are properly installed.
2. If the engine case is excessively greasy, apply degreaser with a paint brush. Do not apply
degreaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden hose. Use only enough pressure to do the
job. WARNING! Wet brakes may have re-
duced stopping ability, increasing the
chance of an accident. Test the brakes af-
ter washing. Apply the brakes several
times at slow speeds to let friction dry out
the linings.
[EWB02312]
NOTICE: Excessive wa-
ter pressure may cause water seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high-pressure de-
tergent applications such as those avail-
able in coin-operated car washers.
[ECB00712]
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or
bottle brush is handy for hard-to-reach pla-
ces.
5. Rinse the ATV off immediately with clean wa- ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
UB1661E0.book Page 1 Thursday, May 12, 2016 2:47 PM
Page 165 of 178
9-2
9
EBU27262StorageShort-term
Always store your ATV in a cool, dry place and, if
necessary, protect it against dust with a porous
cover. NOTICE: Storing the ATV in a poorly ven-
tilated room or covering it with a tarp while it is
still wet, will allow water and humidity to seep
in and cause rust. To prevent corrosion, avoid
damp cellars, stables (because of the presence
of ammonia) and areas where strong chemi-
cals are stored.
[ECB00722]
Long-term
Before storing your ATV for several months: 1. Follow all the instructions in the “Cleaning” section of this chapter.
2. Fill up the fuel tank and add fuel stabilizer (if available) to prevent the fuel from deteriorat-
ing. 3. Perform the following steps to protect the cyl-
inder, piston rings, etc. from corrosion.a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with the starter. (This will coat the cylinder wall
with oil.)
e. Remove the spark plug cap from the spark plug, and then install the spark plug and
the spark plug cap.
4. Lubricate all control cables and the pivoting points of all levers and pedals.
5. Check and, if necessary, correct the tire air pressure, and then block up the ATV so that
all of its wheels are off the ground. Alterna-
tively, turn the wheels a little every month in
order to prevent the tires from becoming de-
graded in one spot.
Specified amount:
7.5 ml of stabilizer to each liter of fuel (or 1
oz of stabilizer to each gallon of fuel)UB1661E0.book Page 2 Thursday, May 12, 2016 2:47 PM
Page 167 of 178
10-1
10
EBU25962
SPECIFICATIONS
Dimensions:Overall length:2070 mm (81.5 in)
Overall width: 1180 mm (46.5 in)
Overall height:
1240 mm (48.8 in)
Seat height: 860 mm (33.9 in)
Wheelbase: 1250 mm (49.2 in)
Ground clearance:
275 mm (10.8 in)
Minimum turning radius: 3200 mm (126 in)Weight:Curb weight:
300.0 kg (661 lb) (YFM70KDXH)
307.0 kg (677 lb) (YFM70KPAH, YFM70KPHH,
YFM70KPXH)
312.0 kg (688 lb) (YFM70KPSH)Noise and vibration level:Noise level (77/311/EEC):80.0 dB(A) at 3125 r/min (YFM70KDXH_EUR/FRA/GBR,
YFM70KPHH, YFM70KPSH, YFM70KPXH)
Uncertainty of measurement: 3.0 dB(A) (YFM70KDXH_EUR/FRA/GBR, YFM70KPHH,
YFM70KPSH, YFM70KPXH) Vibration on seat (EN1032, ISO5008):
Will not exceed 0.5 m/s² (YFM70KDXH_EUR/FRA/GBR,
YFM70KPHH, YFM70KPSH, YFM70KPXH)
Uncertainty of measurement:
0.0 m/s² (YFM70KPHH, YFM70KPSH, YFM70KPXH)
0.1 m/s² (YFM70KDXH_EUR/FRA/GBR)
Vibration on handle (EN1032, ISO5008):
Will not exceed 2.5 m/s² (YFM70KDXH_EUR/FRA/GBR,
YFM70KPHH, YFM70KPSH, YFM70KPXH)
Uncertainty of measurement:
0.3 m/s² (YFM70KDXH_EUR/FRA/GBR, YFM70KPHH,
YFM70KPSH, YFM70KPXH)
Engine:Engine type:Liquid cooled 4-stroke, DOHC
Cylinder arrangement: Single cylinder
Displacement:
708 cm³
Bore × stroke:
103.0 × 85.0 mm (4.06 × 3.35 in)
Compression ratio: 10.1 : 1
Starting system:
Electric starter
Lubrication system: Wet sump
UB1661E0.book Page 1 Thursday, May 12, 2016 2:47 PM
Page 170 of 178
10-4
10
Front wheel:Wheel type:Cast wheel (YFM70KPSH)
Panel wheel (YFM70KDXH, YFM70KPAH, YFM70KPHH,
YFM70KPXH)
Rim size: 12 x 6.0ATRear wheel:Wheel type:
Cast wheel (YFM70KPSH)
Panel wheel (YFM70KDXH, YFM70KPAH, YFM70KPHH,
YFM70KPXH)
Rim size: 12 x 7.5ATFront brake:Type:Disc brake
Operation: Right hand operation
Specified brake fluid:
DOT 4Rear brake:Type:Wet multiple disc brake
Operation:
Left hand and right foot operationFront suspension:Type:Double wishbone
Spring/shock absorber type:
Coil spring/oil damper Wheel travel:
193 mm (7.6 in)
Rear suspension:Type:
Double wishbone
Spring/shock absorber type: Coil spring/oil damper
Wheel travel: 232 mm (9.1 in)Electrical system:Ignition system:TCI
Charging system: AC magnetoBattery:Model:YTX20L-BS
Voltage, capacity: 12 V, 18.0 AhHeadlight(s):Bulb type:Krypton bulbHandlebar-mounted light:Bulb type:
Halogen bulb (YFM70KPAH, YFM70KPHH,
YFM70KPSH, YFM70KPXH)Bulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
UB1661E0.book Page 4 Thursday, May 12, 2016 2:47 PM
Page 171 of 178
10-5
10
Handlebar-mounted light:12 V, 35.0/36.5 W × 1 (YFM70KPAH, YFM70KPHH,
YFM70KPSH, YFM70KPXH)
Tail/brake light: 12 V, 5.0/21.0 W × 1
Meter lighting: EL (Electroluminescent) (YFM70KPAH, YFM70KPHH,
YFM70KPSH, YFM70KPXH)
Neutral indicator light: LED
Fuel level warning light:
LED (YFM70KDXH)
Reverse indicator light: LED
Coolant temperature warning light: LED
EPS warning light:
LED (YFM70KPAH, YFM70KPHH, YFM70KPSH,
YFM70KPXH)
Park indicator light:
LED
Four-wheel-drive indicator light: 12 V, 1.7 W × 1 (YFM70KDXH)
Four-wheel-drive indicator: LCD (YFM70KPAH, YFM70KPHH, YFM70KPXH)
Engine trouble warning light:
LED
High-range indicator light: LED (YFM70KPAH, YFM70KPHH, YFM70KPSH,
YFM70KPXH) Low-range indicator light:
LED (YFM70KPAH, YFM70KPHH, YFM70KPSH,
YFM70KPXH)
Differential gear lock indicator light: LED (YFM70KPSH)
Fuses:Main fuse:
40.0 A
Fuel injection system fuse: 15.0 A
EPS fuse: 40.0 A (YFM70KPAH, YFM70KPHH, YFM70KPSH,
YFM70KPXH)
Headlight fuse: 10.0 A (YFM70KDXH)
15.0 A (YFM70KPAH, YFM70KPHH, YFM70KPSH,
YFM70KPXH)
Signaling system fuse: 10.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse:
10.0 A
Four-wheel-drive motor fuse: 10.0 A (YFM70KPSH)
Radiator fan motor fuse: 20.0 A
UB1661E0.book Page 5 Thursday, May 12, 2016 2:47 PM
Page 175 of 178
12-1
12
INDEX
AAccessories and loading ................................................ 6-5
Accessories, auxiliary jack ........................................... 4-26
Air filter element, cleaning ........................................... 8-37
Axle boots .................................................................... 8-48BBattery ......................................................................... 8-53
Brake fluid, changing ................................................... 8-45
Brake fluid level, checking ........................................... 8-44
Brake lever free play, checking the front ..................... 8-45
Brake lever, front ......................................................... 4-18
Brake levers, checking and lubricating ........................ 8-49
Brake light switches ..................................................... 8-48
Brake pads and friction plates, checking .................... 8-42
Brake pedal and rear brake lever ................................. 4-18
Brake pedal, checking and lubricating ........................ 8-50
Brakes .......................................................................... 8-42
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................ 8-49
Carrier, front ................................................................. 4-23
Carrier, rear .................................................................. 4-23
Chassis fasteners .......................................................... 5-7
Cleaning ......................................................................... 9-1
Coolant .................................................................5-3, 8-29
Coolant temperature warning light ................................ 4-3DDifferential gear lock indicator (YFM70KPSH) ............... 4-6
Differential gear oil ................................................5-3, 8-27Drive lever (YFM70KDXH / YFM70KPXH /
YFM70KPHH / YFM70KPAH) .................................... 4-15
Drive select lever ......................................................... 4-19
Drive select lever and driving in reverse ........................ 6-2
EEngine break-in .............................................................. 6-4
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge .................................. 8-20
Engine stop switch ...................................................... 4-10
Engine trouble warning light .......................................... 4-4
EPS warning light (for EPS model) ................................ 4-5FFinal gear oil ......................................................... 5-3, 8-24
Four-wheel-drive indicator light (YFM70KDXH) ............. 4-5
Four-wheel-drive indicator (YFM70KPXH / YFM70KPHH / YFM70KPSH / YFM70KPAH) ............. 4-5
Fuel ....................................................................... 4-19, 5-3
Fuel level warning light (YFM70KDXH) .......................... 4-4
Fuel tank cap ............................................................... 4-19
Fuses, replacing .......................................................... 8-57HHandlebar switches ....................................................... 4-9
Headlight beam, adjusting ........................................... 8-62
Headlight bulb, replacing ............................................. 8-59
High-range indicator light (YFM70KPXH / YFM70KPHH / YFM70KPSH / YFM70KPAH) ............. 4-3
Horn switch .................................................................. 4-10IIdentification numbers ................................................. 11-1
UB1661E0.book Page 1 Thursday, May 12, 2016 2:47 PM
Page 176 of 178
12-2
12
Indicator lights and warning lights ................................. 4-2
Instruments, lights and switches ................................... 5-7LLabel locations ............................................................... 1-1
Light switch .................................................................. 4-10
Low-range indicator light (YFM70KPXH / YFM70KPHH / YFM70KPSH / YFM70KPAH) .............. 4-3MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................8-5
Maintenance chart, emission control system ................ 8-3
Model label ................................................................... 11-1
Multi-function display (YFM70KPXH / YFM70KPHH / YFM70KPSH / YFM70KPAH) ...................................... 4-6NNeutral indicator light .....................................................4-3OOn-Command differential gear lock switch (YFM70KPSH) ............................................................ 4-13
On-Command four-wheel-drive switch (YFM70KPSH) ............................................................ 4-12
Override switch (YFM70KPSH) .................................... 4-11
Owner’s manual and tool kit .......................................... 8-2PPanels, removing and installing ..................................... 8-9
Park indicator light ......................................................... 4-3
Parking ........................................................................... 6-5
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1RRear brake, adjusting the lever, pedal free play ........... 8-45 Rear knuckle pivots, lubricating ................................... 8-52
Reverse indicator light ................................................... 4-3
Riding your ATV ............................................................. 7-1
SSafety information .......................................................... 2-1
Seat .............................................................................. 4-21
Shock absorber assemblies, adjusting the front and
rear (YFM70KPXH / YFM70KPHH / YFM70KPSH /
YFM70KPAH) ............................................................. 4-24
Spark arrester, cleaning ............................................... 8-39
Spark plug, checking ................................................... 8-17
Specifications .............................................................. 10-1
Speed limiter ................................................................ 4-17
Stabilizer bushes, checking ......................................... 8-51
Starting the engine ......................................................... 6-1
Start switch .................................................................. 4-10
Steering shaft, lubricating ............................................ 8-52
Storage .......................................................................... 9-2
Storage compartment .................................................. 4-22TTail/brake light bulb, replacing ..................................... 8-63
Throttle lever ........................................................ 4-16, 5-4
Throttle lever free play, adjusting ................................. 8-41
Tires ............................................................................... 5-4
Trailer hitch (YFM70KPXH / YFM70KPHH / YFM70KPSH / YFM70KPAH) .................................... 4-25
Troubleshooting ........................................................... 8-65
Troubleshooting charts ................................................ 8-66VValve clearance ............................................................ 8-42
V-belt case drain plug .................................................. 8-41
Vehicle identification number ....................................... 11-1
UB1661E0.book Page 2 Thursday, May 12, 2016 2:47 PM
Page 177 of 178
12-3
12
WWheel hub bearings, checking .................................... 8-51
Wheel, installing ........................................................... 8-64
Wheel, removing .......................................................... 8-64
UB1661E0.book Page 3 Thursday, May 12, 2016 2:47 PM