YAMAHA MT-03 2006 Owner's Guide

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-15
1. Yamaha U-LOCK (optional)
2. Fastening strap
3. Owner’s tool kit
The passenger seat is designed to
fasten a genuine Yamaha U-LOCK to
the bottom of the seat. (Other locks
may not fit.) When fastening a U-
LOCK to the seat, securely fasten it
with the straps. When the U-LOCK is
not fastened to the seat, be sure to se-
cure the straps to prevent losing them.
Rider seat
1. Rider seat mounting bolts
To remove the rider seat
1. Remove the passenger seat.
2. Remove the bolts, and then pull
the rider seat off.
To install the rider seat
1. Projection
2. Seat holder
1. Insert the projection on the front
of the rider seat into the seat hold-
er as shown, place the seat in the
original position, and then tighten
the bolts.
2. Install the passenger seat.
NOTE:
Make sure that the seats are properly
secured before riding.
MY03 01-03 ING 6-10-2005 13:53 Pagina 3-15

INSTRUMENT AND CONTROL FUNCTIONS
3-16
1
2
3
4
5
6
7
8
9
10
A. Distance (spring preload)
Adjust the spring preload as follows.
1. Loosen the locknut.
2. To increase the spring preload
and thereby harden the suspen-
sion, turn the adjusting nut in di-
rection (a). To decrease the
spring preload and thereby soften
the suspension, turn the adjusting
nut in direction (b).
NOTE:
Use the special wrench included
in the owner's tool kit to make the
adjustment.
The spring preload setting is de-
termined by measuring distance
A, shown in the illustration. The
longer distance A is, the lower the
spring preload; the shorter dis-
tance A is, the higher the spring
preload. With each complete turn
of the adjusting nut, distance A
changes by 1.5 mm (0.059 in).
When measuring distance A, the
rear wheel must be raised off the
ground. (See page 6-36).
EAUB1330
Adjusting the shock
absorber assembly
1. Spring preload adjusting nut
2. Locknut
(a) Increasing the spring preload
(b) Decreasing the spring preload
This shock absorber assembly is
equipped with a spring preload adjust-
ing nut.
ECA10100
WARNING0
Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.
MY03 01-03 ING 6-10-2005 13:53 Pagina 3-16

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-17
Spring preload:
Minimum (soft):
Distance A = 174.5 mm (6.87 in)
Standard:
Distance A = 170 mm (6.69 in)
Maximum (hard):
Distance A = 165.5 mm (6.49 in)Spring preload Distance A
SOFT
174.5 mm
(6.87 in)
For light operators and primarily use without passenger
STANDARD
170 mm
(6.69 in)
HARD
165.5 mm
(6.49 in)
For use with heavy operator and passenger and accessories (trunk, bags, etc.)
MY03 01-03 ING 6-10-2005 13:53 Pagina 3-17

EAU15301
Sidestand
1. Sidestand
The sidestand is located on the left
side of the frame. Raise the sidestand
or lower it with your foot while holding
the motorcycle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain situa-
tions. (See further down for an expla-
nation of the ignition circuit cut-off sys-
tem.)
INSTRUMENT AND CONTROL FUNCTIONS
3-18
1
2
3
4
5
6
7
8
9
10
3. Tighten the locknut to the speci-
fied torque.
ECA11240CAUTION:
Always tighten the locknut against
the adjusting nut, and then tighten
the locknut to the specified torque.
EWA10220
WARNING0
This shock absorber contains high-
ly pressurized nitrogen gas. For
proper handling, read and under-
stand the following information be-
fore handling the shock absorber.
The manufacturer cannot be held
responsible for property damage or
personal injury that may result from
improper handling.
Do not tamper with or attempt
to open the gas cylinder.
Do not subject the shock ab-
sorber to an open flame or oth-
er high heat sources, otherwise
it may explode due to exces-
sive gas pressure.
Do not deform or damage the
gas cylinder in any way, as this
will result in poor damping per-
formance.
Always have a Yamaha dealer
service the shock absorber.
Tightening torque:
Locknut:
45 Nm (4.5 m·kgf, 32.5 ft·lbf)
MY03 01-03 ING 6-10-2005 13:53 Pagina 3-18

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
EWA10240
WARNING0
The vehicle must not be ridden
with the sidestand down, or if the
sidestand cannot be properly
moved up (or does not stay up),
otherwise the sidestand could con-
tact the ground and distract the
operator, resulting in a possible
loss of control. Yamaha’s ignition
circuit cut-off system has been de-
signed to assist the operator in ful-
filling the responsibility of raising
the sidestand before starting off.
Therefore, check this system regu-
larly as described below and have
a Yamaha dealer repair it if it does
not function properly.
3-19
EAU15311
Ignition circuit cut-off
system
The ignition circuit cut-off system
(comprising the sidestand switch,
clutch switch and neutral switch) has
the following functions.
It prevents starting when the
transmission is in gear and the
sidestand is up, but the clutch
lever is not pulled.
It prevents starting when the
transmission is in gear and the
clutch lever is pulled, but the side-
stand is still down.
It cuts the running engine when
the transmission is in gear and
the sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system accord-
ing to the following procedure.
EWA10250
WARNING0
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
MY03 01-03 ING 6-10-2005 13:53 Pagina 3-19

INSTRUMENT AND CONTROL FUNCTIONS
3-20
1
2
3
4
5
6
7
8
9
10
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
NOTE:
This check is most reliable if performed with a
warmed-up engine.
The neutral switch may be defective.
The motorcycle should not be riddenuntil checked by a
Yamaha dealer.
The sidestand switch may be defective.
The motorcycle should not be riddenuntil checked by a
Yamaha dealer.
The clutch switch may be defective.
The motorcycle should not be riddenuntil checked by a
Yamaha dealer.
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The system is OK. The motorcycle can be ridden.
YES NO
NO YES
NO YES
MY03 01-03 ING 6-10-2005 13:53 Pagina 3-20

1
2
3
4
5
6
7
8
9
10
PRE-OPERATION CHECKS
4-1
EAU15591
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpected-
ly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage
or loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough vi-
sual inspection, to check the following points before each ride.
NOTE:
Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very
short time; and the added safety it assures is more than worth the time involved.
EWA11150
WARNING0
If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operat-
ing the vehicle.
MY03 04-06 ING 6-10-2005 9:24 Pagina 1

PRE-OPERATION CHECKS
4-2
1
2
3
4
5
6
7
8
9
10
ITEM
Fuel
Engine oil
Coolant
Front brake
Rear brake
EAU15603
Pre-operation check list
CHECKS
• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
• Check oil level in oil tank.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.PAGE
3-12
6-8
6-12
3-11, 6-20, 6-21, 6-26
3-11, 6-20, 6-21, 6-26
MY03 04-06 ING 6-10-2005 9:24 Pagina 2

1
2
3
4
5
6
7
8
9
10
PRE-OPERATION CHECKS
4-3
ITEM
Clutch
Throttle grip
Control cables
Drive chain
Wheels and tires
Brake pedal
Brake and
clutch levers
Sidestand
Chassis fastenersCHECKS
• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.
• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate
cable and grip housing.
• Make sure that operation is smooth.
• Lubricate if necessary.
• Check chain slack.
• Adjust if necessary.
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.
• Make sure that operation is smooth.
• Lubricate pedal pivoting point if necessary.
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
• Make sure that operation is smooth.
• Lubricate pivot if necessary.
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.PAGE
3-10, 6-19, 6-26
6-15, 6-25
6-25
6-23, 6-24
6-16, 6-19
6-26
6-26
6-27
–
MY03 04-06 ING 6-10-2005 9:24 Pagina 3

PRE-OPERATION CHECKS
4-4
1
2
3
4
5
6
7
8
9
10
ITEM
Instruments, lights,
signals and switches
Sidestand
switchCHECKS
• Check operation.
• Correct if necessary.
• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.PAGE
3-3, 3-9
3-20
MY03 04-06 ING 6-10-2005 9:24 Pagina 4