clutch YAMAHA MT-03 2018 User Guide

Periodic maintenance an d a djustment
6-4
6
EAU71372
General maintenance an d lu brication chart
NO. ITEM
1 *Dia
gnostic system
check • Perform dynamic inspection
using Yamaha diagnostic tool.
• Check the error codes. √√√√√√
2 *Air filter element • Replace. √√
3 Air filter case
check hose • Clean.
√√√√√
4Clutch • Check operation.
•Adjust. √√√√√
5 *Front brake • Check operation, fluid level,
and for fluid leakage.
• Replace brake pads if neces- sary. √√√√√√
6 *Rear brake • Check operation, fluid level,
and for fluid leakage.
• Replace brake pads if neces- sary. √√√√√√
7 *Brake hoses • Check for cracks or damage.
√√√√√
• Replace. Every 4 years
8 *Brake flui d • Change. Every 2 years
9 *Wheels • Check runout and for damage.
• Replace if necessary. √√√√
10 *Tires • Check tread depth and for
damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary. √√√√√
11 *Wheel bearin gs • Check bearing for looseness or
damage. √√√√
12 *Swin
garm pivot
b earin gs • Check operation and for exces-
sive play. √√√√
13 Drive chain • Check chain slack, alignment
and condition.
• Adjust and lubricate chain with a special O-ring chain lubricant
thoroughly. Every 800 km (500 mi) and after
washing the motorcycle, riding
in the rain or riding in wet areasX 1000 km
CHECK OR
MAINTENANCE JOB
X 1000 mi ODOMETER
READINGSANNUAL CHECK
1 10203040
0.6 6 12 18 24
UB9AE0E0.book Page 4 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-5
6
14 *Steerin g b earin gs • Check bearing assemblies for
looseness. √√ √
• Moderately repack with lithium- soap-based grease. √√
15 *Chassis fasteners • Make sure that all nuts, bolts
and screws are properly tight-
ened. √√√√√
16 Brake lever pivot
shaft • Lubricate with silicone grease.
√√√√√
17 Brake ped
al pivot
shaft • Lubricate with lithium-soap-
based grease. √√√√√
18 Clutch lever pivot
shaft • Lubricate with lithium-soap-
based grease. √√√√√
19 Shift pe
dal pivot
shaft • Lubricate with lithium-soap-
based grease. √√√√√
20 Si destan d • Check operation.
• Lubricate with lithium-soap-
based grease. √√√√√
21 *Sidestan d switch • Check operation and replace if
necessary. √√√√√√
22 *Front fork • Check operation and for oil
leakage.
• Replace if necessary. √√√√
23 *Shock a
bsor ber
assem bly • Check operation and for oil
leakage.
• Replace if necessary. √√√√
24 En gine oil • Change (warm engine before
draining).
• Check oil level and vehicle for oil leakage. At the initial interval and
when the oil change indi-
cator flashes or comes on [every 5000km (3000 mi)]. √
25 En
gin
e oil filter
cartri dge • Replace.
√√√
26 *Coolin g system • Check coolant level and vehicle
for coolant leakage. √√√√√
• Change. Every 3 years
27 *Front an
d rear
b rake switches • Check operation.
√√√√√√
NO. ITEM
X 1000 km
CHECK OR
MAINTENANCE JOB
X 1000 mi
ODOMETER READINGS
ANNUAL CHECK
110203040
0.66121824
UB9AE0E0.book Page 5 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-10
6
TIP
Make sure that the O-ring is properly
seated.
8. Install the new oil filter cartridge
with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.
9. Install the engine oil drain bolt and its new gasket, and then tighten
the bolt to the specified torque.
TIP
Install the new gasket as shown.
10. Refill with the specified amount of the recommended engine oil, and
then install and tighten the oil filler
cap.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
NOTICE
ECA11621
zIn or der to prevent clutch slip-
pa ge (since the en gine oil also
lu bricates the clutch), do not
mix any chemical add itives. Do
not use oils with a d iesel speci-
fication of “CD” or oils of a hi gh-
er quality than specified . In
1. O-ring
1. Torque wrench
Tightenin g torque:
Oil filter cartridge: 17 N·m (1.7 kgf·m, 13 lb·ft)
1
1. Engine oil drain bolt
2. Gasket
Tightening torque:
Engine oil drain bolt: 20 N·m (2.0 kgf·m, 15 lb·ft)
Recommen ded en gine oil:
See page 8-1.
Oil quantity:
Oil change:1.80 L (1.90 US qt, 1.58 Imp.qt)
With oil filter removal:
2.10 L (2.22 US qt, 1.85 Imp.qt)
2
1
UB9AE0E0.book Page 10 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-18
6
EAU33893
A djustin g the clutch lever free
play
Measure the clutch lever free play as
shown.
Periodically check the clutch lever free
play and, if necessary, adjust it as fol-
lows.
To increase the clutch lever free play,
turn the clutch lever free play adjusting
bolt at the clutch lever in direction (a).
To decrease the clutch lever free play,
turn the adjusting bolt in direction (b).
TIP
If the specified clutch lever free play
cannot be obtained as described
above, proceed as follows.
1. Fully turn the adjusting bolt at the
clutch lever in direction (a) to loos-
en the clutch cable.
2. Loosen the locknut at the crank- case. 3. To increase the clutch lever free
play, turn the clutch lever free play
adjusting nut in direction (a). To
decrease the clutch lever free
play, turn the adjusting nut in di-
rection (b).
4. Tighten the locknut.
1. Clutch lever free play adjusting bolt
2. Locknut
3. Clutch lever free play
Clutch lever free play: 10.0–15.0 mm (0.39–0.59 in)
3
(a)
1
2
(b)
1. Locknut
2. Clutch lever free play adjusting nut
2
(b)
(a)
1
UB9AE0E0.book Page 18 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-26
6
EAU23144
Checkin g an d lu bricatin g the
b rake an d clutch levers
The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.
Brake lever
Clutch lever
EAU23203
Checkin g an d lu bricatin g the
si destan d
The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated
if necessary.
WARNING
EWA10732
If the si destan d d oes not move up
an d d own smoothly, have a Yamaha
d ealer check or repair it. Otherwise,
the si destan d coul d contact the
g roun d an d d istract the operator, re-
sultin g in a possi ble loss of control.
Recommen ded lu bricants:
Brake lever: Silicone grease
Clutch lever: Lithium-soap-based grease
Recommen ded lu bricant:
Lithium-soap-based grease
UB9AE0E0.book Page 26 Thursday, March 23, 2017 2:48 PM

Specifications
8-1
8
Dimensions:
Overall length:2090 mm (82.3 in)
Overall width:
745 mm (29.3 in)
Overall height: 1135 mm (44.7 in)
Seat height: 780 mm (30.7 in)
Wheelbase:
1380 mm (54.3 in)
Ground clearance: 160 mm (6.30 in)
Minimum turning radius: 2.7 m (8.86 ft)
Wei ght:
Curb weight:
169 kg (373 lb)
Engine:
Combustion cycle:
4-stroke
Cooling system:
Liquid cooled
Valve train: DOHC
Cylinder arrangement: Inline
Number of cylinders:
2-cylinder
Displacement: 321 cm³
Bore × stroke:
68.0 × 44.1 mm (2.68 × 1.74 in)
Compression ratio:
11.2 : 1
Starting system: Electric starter
Lubrication system: Wet sump
Engine oil:
Recommended brand:
YAMALUBE
SAE viscosity grades: 10W-40
Recommended engine oil grade: API service SG type or higher, JASO
standard MA Engine oil quantity:
Oil change:
1.80 L (1.90 US qt, 1.58 Imp.qt)
With oil filter removal: 2.10 L (2.22 US qt, 1.85 Imp.qt)
Coolant quantity:
Coolant reservoir (up to the maximum level
mark):0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator (including all routes):
0.81 L (0.86 US qt, 0.72 Imp.qt)
Air filter:
Air filter element:Oil-coated paper element
Fuel:
Recommended fuel:
Regular unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity:
14 L (3.7 US gal, 3.1 Imp.gal)
Fuel reserve amount: 3.0 L (0.79 US gal, 0.66 Imp.gal)
Fuel injection:
Throttle body:
ID mark: BR51 00
Spark plu g(s):
Manufacturer/model:
NGK/LMAR8A-9
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)
Clutch:
Clutch type:Wet, multiple-disc
Drivetrain:
Primary reduction ratio:
3.043 (70/23)
Final drive: Chain
Secondary reduction ratio: 3.071 (43/14)
Transmission type:
Constant mesh 6-speed
Gear ratio: 1st:
2.500 (35/14)
2nd: 1.824 (31/17)
3rd: 1.348 (31/23)
UB9AE0E0.book Page 1 Thursday, March 23, 2017 2:48 PM

10-1
10
Index
A
ABS ....................................................... 3-14
ABS warning light ................................... 3-3
Air filter element and check hose,
replacing and cleaning ....................... 6-13
Auxiliary light......................................... 6-33
B
Battery .................................................. 6-29
Brake and clutch levers, checking
and lubricating .................................... 6-26
Brake and shift pedals, checking and lubricating .................................... 6-25
Brake fluid, changing ............................ 6-22
Brake fluid level, checking .................... 6-21
Brake lever ............................................ 3-13
Brake lever free play, checking............. 6-19
Brake light switches.............................. 6-19
Brake pedal........................................... 3-14
C
Cables, checking and lubricating ......... 6-24
Canister................................................... 6-8
Care ........................................................ 7-1
Catalytic converter ................................ 3-18
Clutch lever ........................................... 3-12
Clutch lever free play, adjusting ........... 6-18
Coolant ................................................. 6-11
D
Data recording, vehicle ........................... 9-3
Diagnostic connector.............................. 9-2
Dimmer switch ...................................... 3-11
Drive chain, cleaning and lubricating .... 6-24
Drive chain slack................................... 6-22
E
Engine break-in....................................... 5-4
Engine oil and oil filter cartridge ............. 6-8
Engine serial number .............................. 9-1
Engine stop switch ............................... 3-12
Engine trouble warning light ................... 3-3
F
Front and rear brake pads, checking.... 6-20
Front fork, checking .............................. 6-27
Fuel ....................................................... 3-16
Fuel tank cap ........................................ 3-15
Fuel tank overflow hose ........................ 3-17
Fuses, replacing.................................... 6-30
H
Handlebar switches .............................. 3-11
Headlight bulb, replacing ...................... 6-32
Helmet holders...................................... 3-20
High beam indicator light........................ 3-2 Horn switch .......................................... 3-12
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system............... 3-23
Indicator lights and warning lights ......... 3-2
L
License plate light bulb, replacing........ 6-34
Luggage strap holders ......................... 3-22
M
Main switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission
control system ..................................... 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-4
N
Neutral indicator light ............................. 3-2
O
Oil pressure warning light ....................... 3-2
P
Parking ................................................... 5-4
Part locations ......................................... 2-1
Pass switch .......................................... 3-11
S
Safety information .................................. 1-1
Seats .................................................... 3-18
Shifting ................................................... 5-3
Shift pedal ............................................ 3-13
Shift timing indicator light....................... 3-4
Shock absorber assembly, adjusting............................................. 3-21
Sidestand ............................................. 3-23
Sidestand, checking and lubricating .... 6-26
Spark plugs, checking ............................ 6-7
Specifications ......................................... 8-1
Starting the engine ................................. 5-2
Start switch .......................................... 3-12
Steering, checking................................ 6-28
Storage ................................................... 7-4
Storage compartment .......................... 3-21
Supporting the motorcycle................... 6-35
Swingarm pivots, lubricating ................ 6-27
T
Tail/brake light ...................................... 6-33
Throttle grip and cable, checking and lubricating .................... 6-25
Throttle grip free play, checking........... 6-14
Tires ...................................................... 6-15
Tool kit.................................................... 6-2
UB9AE0E0.book Page 1 Thursday, March 23, 2017 2:48 PM